Panasonic Kx Ta824 Programming Manual

7.3 Screen Customize
Programming Manual 111
3.Re-enter the same code for verification.
If the entered codes do not match, an error message will be displayed.
Click OK to return to step 2 above.
4.Click OK.
7.3 Screen Customize
Allows you to specify which system data setting screens and menu options can be accessed when logged 
in to Maintenance Console at User level.
This option is only available at Installer level.
To customize the displayed options
1.
From the View menu, select Screen Customize.
A...

7.4 System Data Setting Menu
112 Programming Manual 

Programming Manual 113
Section 8
PC Programming—Utility
This section describes the Utility menu, which contains 
options for performing system maintenance on the PBX. 

8.1 Firmware Upgrade
114 Programming Manual
8.1 Firmware Upgrade
Allows installation of upgrades to the system software stored within the PBX. Only install upgrades provided 
by certified Panasonic dealers.
To upgrade system software
1.
From the Utility menu, select Firmware Upgrade.
The Firmware Upgrade screen will be displayed.
2.Click Select.
The Open dialog box will be displayed.
3.Navigate to the folder containing the system software file you want to install.
4.Select the file.
5.Click Open.
 If...

8.2 Quick Setup
Programming Manual 115
 While downloading system data from the PBX
The Firmware Upgrade screen will be displayed automatically. Reselect the system 
software file and perform the upgrade again.
 While writing the new software to the PBX
The PBX will be unable to start properly. The Firmware Upgrade screen will be 
displayed automatically. Reselect the system software file and perform the upgrade 
again.
 While restoring system data to the PBX
The Firmware Upgrade process will be...

8.2 Quick Setup
116 Programming Manual
To set up basic items for the PBX
1.
From the Utility menu, click Quick Setup.
The Automatic Configuration for CO Line Type screen will be displayed.
 If you do not want to automatically configure outside (CO) line types, deselect the check box.
2.Click Next
The Step 2 screen will be displayed.
3.Select the jack number you wish to register as the operator extension, or Disable.
 If you do not want to configure the operator extension, deselect the check box. 

8.2 Quick Setup
Programming Manual 117
4.Click Next.
The Step 3 screen will be displayed.
5.Enter the desired extension number and name (if required) for each jack to configure in the table.
 If you do not want to configure extension numbers and names, deselect the check box.
6.Click Next.
The Step 4 screen will be displayed.
7.For each outside (CO) line, select the ringing assignment.
 Select All extensions to have all extensions ring for calls from that outside (CO) line.
 Select a jack number to...

8.3 System Reset
118 Programming Manual
8.Click Next.
The Step 5 screen will be displayed.
9.Enter the date and time.
 By default, the date and time of the PC are shown in these boxes.
10.Enter the desired system password, to be used to log on to the PBX.
 The password must be from 4 to 7 digits long.
 You must enter the same password 2 times, for confirmation.
 Be sure to make a note of the password entered here, as it will be required to log on to the PBX.
11.Click Finish.
 The data items set in...

8.4 System Data Clear
Programming Manual 119
2.Click Ye s.
The PBX will be disconnected from Maintenance Console, and will reset.
8.3.2 Default
Resets the PBX, and returns programming settings to their default values.
This option clears all settings within the PBX. Use this feature only when necessary, as all setting data within 
the PBX will be lost. If required, take a backup of system data in advance, using 5.7 File Transfer PBX to PC.
To clear all settings and reset the PBX
1.
From the Utility menu,...

8.5 DISA OGM Clear
120 Programming Manual
A completion message will be displayed.
4.Click OK.
8.5 DISA OGM Clear
Initializes the outgoing messages (OGMs) for the DISA feature.
DISA OGMs on both the preinstalled OGM card and the optional OGM card (if present) will be deleted.
Notes
It is necessary to perform the procedure below to clear outgoing messages (OGMs) for DISA when 
starting the PBX for the first time.
To clear all DISA OGMs
1.
From the Utility menu, select DISA OGM Clear.
A confirmation message...