Panasonic Kx Ta824 Programming Manual

2.2 PT Programming—Procedures
Programming Manual 61
[618] Message Waiting for Another Extension
Specifies whether an extension can use the Message Waiting for Another Extension feature. If this program 
is disabled, an extension user cannot use a button as a Message for Another Extension button.
Feature Manual References
1.1.83 Message Waiting for Another Extension
[619] SLT Message Waiting
Enables the PBX to send dial tone 3 as a message waiting notification to an SLT.
Feature Manual References
1.1.82...

2.2 PT Programming—Procedures
62 Programming Manual
Feature Manual References
1.1.77 Live Call Screening (LCS) (Voice Mail APT Integration only)
1.1.120 Voice Mail APT Integration
[621] BV Resource
Selects the BV resource to which the extension belongs.
Feature Manual References
1.1.8 Built-in Voice Message (BV)
[622] BV for Extension
Enables the BV feature for each extension.
Feature Manual References
1.1.8 Built-in Voice Message (BV)
621NEXTextension jack no.
extension jack no.01-02=
Resource 1...

2.2 PT Programming—Procedures
Programming Manual 63
[625] BV Access Code through CO Line
Specifies a voice message access code used to play back and/or erase voice messages through outside 
(CO) lines.
Conditions
 A voice message access code should be different from the corresponding extension number. If the 
voice message access code is the same as an extension number, dialing that number will access 
the extension, not the voice message area. 
 A code that starts with a number already assigned as...

2.2 PT Programming—Procedures
64 Programming Manual
[627] SLT Ring Wait Time for New Call
Selects the length of time the ringing for a call is delayed when the call follows immediately after the previous 
unanswered call. When receiving 2 calls in quick succession, for example, when a call waiting in a queue is 
directed to an extension immediately after the previous call stops ringing, some SLTs require a pause, after 
the first call stops ringing, to receive the second calls Caller ID information....

2.2 PT Programming—Procedures
Programming Manual 65
[700-702] Doorphone Ringing—Day/Night/Lunch
Enables doorphone call reception in each time service mode.
Feature Manual References
1.1.48 Doorphone Call
[703-705] Door Opener—Day/Night/Lunch
Enables door opening in each time service mode.
Feature Manual References
1.1.46 Door Open
7XNEXTSTOREEND
(1…
4/    ) (01…
24/    )
SELECT
or
SELECT#
Go to another jack number
Go to another doorphone number
Go to next or prev.
jack number
➞
Go to next or prev....

2.2 PT Programming—Procedures
66 Programming Manual
[706] Doorphone Ring Tone Pattern
Selects the ring tone pattern for incoming doorphone calls.
Conditions
 It is recommended that you set a different ring tone pattern from the ring tone patterns specified in 
[115] Extension Ring Tone Pattern and [423] CO Line Ring Tone Pattern.
Programming Manual References
[115] Extension Ring Tone Pattern
[423] CO Line Ring Tone Pattern
Feature Manual References
1.1.48 Doorphone Call
1.1.108 Ring Tone Pattern...

2.2 PT Programming—Procedures
Programming Manual 67
[708] Doorphone Ring Time
Selects the length of time until the ringing stops and the call is canceled when there is no answer.
Feature Manual References
1.1.48 Doorphone Call
[709] Door Open Duration
Specifies the length of time the door stays unlocked.
Feature Manual References
1.1.46 Door Open
[710] Doorphone Ring/Chime
Selects whether doorphone calls ring at extensions or at dedicated door chimes.
Programming Manual References
[700-702] Doorphone...

2.2 PT Programming—Procedures
68 Programming Manual
[711] Doorphone Chime Assignment
Selects the relay to which a doorbell or a door chime is connected, for use when Chime or Ring & Chime 
is selected in [710] Doorphone Ring/Chime. 
Conditions
 A relay not connected to a door opener should be selected.
Programming Manual References
[710] Doorphone Ring/Chime
Feature Manual References
1.1.47 Doorbell/Door Chime
1.1.48 Doorphone Call
[712] Doorphone Chime Pattern
Selects the doorphone chime pattern for...

2.2 PT Programming—Procedures
Programming Manual 69
d.Parity Bit: Parity bit indicates what type of parity is used to detect errors in the string of bits 
composing a character. Make an appropriate selection depending on the requirements of the PC 
or printer.
e.Stop Bit Length: Stop bit indicates the end of a bit string that composes a character. Select an 
appropriate value depending on the requirements of the PC or printer.
Conditions
 * Select None when the printer does not require error checking.
...

2.2 PT Programming—Procedures
70 Programming Manual
Feature Manual References
1.1.112 Station Message Detail Recording (SMDR)
[802] Incoming/Outgoing Call Selection for Printing
Selects whether the dialed digits of incoming and outgoing outside (CO) line calls are printed.
Notes
Outgoing Call: On (Print all calls)/Off (No printing)/Toll (Print toll calls only)
Incoming Call: On (Print all calls)/Off (No printing)
Programming Manual References
[302-305] TRS—COS 2-5 Denied Code
Feature Manual References...