Panasonic DLP Projector PT-DZ870U PT-DW830U PT-DX100U Operating Instructions

Chapter 4 Settings — [PROJECTOR SETUP] menu
ENGLISH - 111
[LAMP POWER]
Switch the brightness of the lamp according to the operating environment of the projector or the purpose.
1) Press as to select [LAMP POWER].
2)  
Press 
 qw to switch the item.
[NORMAL] Select when high luminance is required.
[ECO] Select when high luminance is not required.
Note
 fWhen [ECO] is set, you can reduce power consumption and operation noise, and extend the life of the lamp.
[BRIGHTNESS CONTROL]
The projector is equipped...

Chapter 4 Settings — [PROJECTOR SETUP] menu
112 - ENGLISH
Setting [BRIGHTNESS CONTROL SETUP]
Set brightness control operation.
1) Press as to select [BRIGHTNESS CONTROL].
2)  
Press the  button.
 f The  [BRIGHTNESS CONTROL] screen is displayed.
3) Press  as to select [BRIGHTNESS CONTROL SETUP].
4)  
Press the  button.
 f The  [BRIGHTNESS CONTROL SETUP] screen is displayed.
5) Press  as to select [MODE].
6)  
Press 
 qw to switch the item.
 fThe items will switch each time you press the button.
[OFF] Does...

Chapter 4 Settings — [PROJECTOR SETUP] menu
ENGLISH - 113
16) Press the  button.
 fThe set [MODE] and [LINK] are enabled, and LAMP  RELAY screen alert is displayed when the [LAMP RELAY] setting is [OFF]. When 
[CALIBRATION MESSAGE] is set to [ON], a calibration running message is displayed which will automatically disappear 30 seconds 
after calibration completes.
 f If the  button is pressed with [MODE] in [BRIGHTNESS CONTROL  SETUP] set to other than [OFF], the brightness of the 
lamp at the time the...

Chapter 4 Settings — [PROJECTOR SETUP] menu
114 - ENGLISH
When [MODE] of [BRIGHTNESS CONTROL SETUP] is set to 
[AUTO] and [LINK] is set from [GROUP A] to [GROUP D]
The screen shows the status of the brightness control of 
synchronized projectors (up to eight units), including the projector 
being controlled through the on-screen menu.
2 1
3
4
5 
7
8
1:
2:
3:
4:
5:
6:
7:192. 168. 30.   2
192. 168. 30.   3
192. 168. 30.   4
LINK
UPDATE PROJECTOR
GROUP A
PROJECTOR2
PROJECTOR3
BRIGHTNESS CONTROL STATUS
MENU...

Chapter 4 Settings — [PROJECTOR SETUP] menu
ENGLISH - 115
Brightness control adjustment procedure example
The steps exemplify an adjustment to link the brightness of eight projectors connected in a network.
1) Connect all projectors to the hub using LAN cables. (x   page   137)
2)  
Switch on all projectors and start projection.
3)

 
Set [LAMP
  SELECT] to either [DUAL] or [SINGLE] for all projectors.
4)
 
Set [MODE] of [BRIGHTNESS CONTROL
  SETUP] to [OFF], and select [APPLY], and then press the...

Chapter 4 Settings — [PROJECTOR SETUP] menu
116 - ENGLISH
[STANDBY MODE]
Set the power consumption during the standby.
1) Press as to select [STANDBY MODE].
2)  
Press 
 qw to switch the item.
 fThe items will switch each time you press the button.
[NORMAL] Use this setting to use the network function during standby.
[ECO] Use this setting to reduce power consumption during standby.
Note
 fIn the [ECO] setting, the network function, the  terminal, and some RS - 232C commands become inoperable during...

Chapter 4 Settings — [PROJECTOR SETUP] menu
ENGLISH - 117
7) Press qw to select “hour” or “minute”, and press as or the number ( - ) buttons to set a 
time, and then press the  button.
8)
 
Press 
 asqw to select [COMMAND].
9)
 
Press the  button.
 f The  [COMMAND] detailed screen is displayed.
10) Press  as to select a [COMMAND].
 fFor [COMMAND] which requires detailed settings, the items of the detailed settings will switch each time you press  qw .
 fWhen [INPUT] is selected, press the  button, and...

Chapter 4 Settings — [PROJECTOR SETUP] menu
118 - ENGLISH
3) Press asqw to select an input.
 fThe items will switch each time you press the button.
[LAST USED] Keeps the input selected last.
[VIDEO] Sets the input to VIDEO.
[RGB1] Sets the input to RGB1.
[RGB2] Sets the input to RGB2.
[DVI
- D] Sets the input to DVI
- D.
[HDMI] Sets the input to HDMI.
[DIGITAL LINK] Sets the input to DIGITAL LINK.
[SDI]
*1Sets the input to SDI.
[INPUT1] - [INPUT10]
*2Sets the input to DIGITAL LINK, and switch the input...

Chapter 4 Settings — [PROJECTOR SETUP] menu
ENGLISH - 119
4) Press qw to switch the item.
[9600]
Select the proper speed.
[19200]
[38400]
5) Press  as to select [(OUT) PARITY].
6)  
Press 
 qw to switch the item.
 fThe items will switch each time you press the button.
[NONE]
Select the parity condition.
[EVEN]
[ODD]
Setting the response
1) Press  as to select [RS-232C].
2)  
Press the  button.
 f The  [RS-232C]  screen is displayed.
3) Press  as to select [RESPONSE(ID ALL)].
4)  
Press 
 qw to switch the...

Chapter 4 Settings — [PROJECTOR SETUP] menu
120 - ENGLISH
[SIGNAL FREQUENCY]Displays the frequency of the input signal.
[PROJECTOR RUNTIME] Displays the operation times of the projector.
[LAMP1]
*3Displays the runtime and status of Lamp 1.
[LAMP2]
*3Displays the runtime and status of Lamp 2.
[INTAKE AIR TEMP.]
*2Displays the status of the air intake temperature of the projector .
[OPTICS MODULE TEMP.]
*2Displays the status of the internal temperature of the projector .
[AROUND LAMP TEMP.]
*2Displays the...