Panasonic DLP Projector PT-DZ870U PT-DW830U PT-DX100U Operating Instructions

Chapter 4 Settings — [POSITION] menu
ENGLISH - 81
[CORNER CORRECTION]Adjusts any distortion in the four corners of the projected image.
[CURVED] Adjusts any curved distortion in the projected image.
[PC-1]
*1
Uses the computer to perform geometric adjustment.
[PC-2]*1
[PC-3]*1
*1 Advanced skills are necessary to use a computer to control geometric adjustment. Consult your dealer . Up to three geometric adjustments 
performed using the computer can be saved.
Setting [KEYSTONE] or [CURVED]
1) Press  as to...

Chapter 4 Settings — [POSITION] menu
82 - ENGLISH
[CURVED]
[VERTICAL BALANCE]
[HORIZONTAL BALANCE]
[MAINTAIN ASPECT RATIO]
Select [ON] to correct while keeping the aspect ratio.
Setting [CORNER CORRECTION]
1) Press  as to select [GEOMETRY(2D)].
2)  
Press 
 qw to select [CORNER CORRECTION].
3)
 
Press the  button.
 f The  [GEOMETRY:CORNER CORRECTION] screen is displayed.
4) Press  as to select the item to adjust, and press the  button.
5)  
Press 
 asqw to adjust.
[CORNER CORRECTION]
[UPPER LEFT]
[UPPER...

Chapter 4 Settings — [POSITION] menu
ENGLISH - 83
[KEYSTONE][SUB KEYSTONE]
[LINEARITY]
Note
 fThe menu or logo may run of f the screen when adjustments are performed with [KEYSTONE(3D)]. fCorrecting up to ±40° for the tilt in the vertical direction is available in the adjustments with [KEYST ONE(3D)]. However
, the image quality 
will degrade and it will get harder to focus with more correction. Install the projector so that the correction will be as small as possible. (The 
correction is ±30° when the...

Chapter 4 Settings — [ADVANCED MENU] menu
84 - ENGLISH
[ADVANCED MENU] menu
On the menu screen, select [ADVANCED MENU] from the main menu, and select an item from 
the sub-menu.
Refer to “Navigating through the menu” (x
  page   65) for the operation of the menu screen.
 fAfter selecting the item, press 

asqw to adjust.
[DIGITAL CINEMA REALITY]
You can increase the vertical resolution and enhance the image quality by performing cinema processing when the PAL (or SECAM) 576i 
signal, the NTSC 480i...

Chapter 4 Settings — [ADVANCED MENU] menu
ENGLISH - 85
Blanking correction Item OperationAdjustmentRange of adjustment
Top of the screen [UPPER] Press the q 
button. The blanking zone 
moves upward.
PT-
DZ870U: Top to bottom 
0 - 599
PT
-

DW830U: Top to bottom  0 - 399
PT
-

DX100U: Top to bottom  0 - 383
Press the w 
button. The blanking zone 
moves downward.
Bottom of the  screen [LOWER]Press the w 
button. The blanking zone 
moves upward.
Press the q 
button. The blanking zone 
moves downward.
Left...

Chapter 4 Settings — [ADVANCED MENU] menu
86 - ENGLISH
[EDGE BLENDING]
The edge blending function allows multiple projector images to be seamlessly overlapped by using the inclination of the brightness at the 
overlapped area.
1) Press as to select [EDGE BLENDING].
2)  
Press 
 qw to switch the item.
 fThe items will switch each time you press the button.
[OFF] Sets the edge blending function to off.
[ON] Use the setting value of the internal distortion of the set for the inclination of the edge blending...

Chapter 4 Settings — [ADVANCED MENU] menu
ENGLISH - 87
15) Press as to select [UPPER], [LOWER], [LEFT], or [RIGHT] in [BLACK BORDER WIDTH]
16)  
Press 
 qw to set the region (width) of the [BLACK BORDER WIDTH] adjustment.
 fWhen PT- DZ870U is used, proceed to Step  17).
 fWhen PT-

DW830U or PT
-
 DX100U is used, proceed to Step  19).
17) Press as to select [UPPER KEYSTONE AREA], [LOWER KEYSTONE AREA], [LEFT KEYSTONE 
AREA], or [RIGHT KEYSTONE AREA].
18)
 
Press 
 qw to adjust the tilt of the border...

Chapter 4 Settings — [ADVANCED MENU] menu
88 - ENGLISH
[FRAME LOCK]
Set this to view 3D display when the vertical scanning frequency of the signal is 25 Hz, 50 Hz, and 100 Hz.
1) Press as to select [FRAME LOCK].
2)  
Press 
 qw to switch the item.
 fThe items will switch each time you press the button.
[OFF] Decreases the flickering of the display.
[ON] Synchronizes the display to the vertical scanning frequency of the input signal.
Note
 f[FRAME LOCK] is not displayed when the vertical scanning...

Chapter 4 Settings — [DISPLAY LANGUAGE] menu
ENGLISH - 89
[DISPLAY LANGUAGE] menu
On the menu screen, select [DISPLAY LANGUAGE] from the main menu, and display the sub-
menu.
Refer to “Navigating through the menu” (x
  page   65) for the operation of the menu screen.
 fPress 

as to select a language, and press the  button to set.
Changing the display language
You can select the language of the on-screen display.
ENTER
DISPLAY LANGUAGE
SELECT
SET
 fVarious menus, settings, adjustment screens, control...

Chapter 4 Settings — [3D SETTINGS] menu
90 - ENGLISH
[3D SETTINGS] menu
On the menu screen, select [3D SETTINGS] from the main menu, and select \
an item from the 
sub-menu.
Refer to “Navigating through the menu” (x
  page   65) for the operation of the menu screen.
 fAfter selecting the item, press 

asqw to set.
[3D SYSTEM SETTING]
Set a picture display method for use during 3D signal input as necessary for the 3D system in use.
1) Press  as to select [3D SYSTEM SETTING].
2)  
Press 
 qw to switch the...