Panasonic DLP Projector PT-DZ870U PT-DW830U PT-DX100U Operating Instructions

Chapter 4 Settings — [NETWORK] menu
ENGLISH - 141
Error information page
When [Error (Detail)] or [Warning (Detail)] is displayed in the self-diagnosis display of the [Projector status] screen, click it to display the 
error/warning details.
 f The projector may go into the standby status to protect the projector depending on the contents of the error .
1
1 Self-diagnosis result display
Displays the item check results.
[OK]:
Indicates that operation is normal.
[F
AILED]:
Indicates that there is a...

Chapter 4 Settings — [NETWORK] menu
142 - ENGLISH
ParameterDescription
[AIR FILTER] There is too much dust accumulated in the air filter. Turn the  switch 
 (
x
  page   57), and clean the air filter. (x   page   160)
 r[WARNING] items
Parameter Description
[AC POWER] AC input voltage is weak. Use electric wiring that can sufficiently withstand the power 
consumption of the projector.
[LOW-TEMPERATURE] The temperature around the optics module inside the projector is low
. Projection cannot 
be started...

Chapter 4 Settings — [NETWORK] menu
ENGLISH - 143
[Mail error log] page
Click [Status] → [Mail error log].
Display E-mail error information if failed to send periodic E-mails.
Note
 f[Access error log] and [Mail error log] display the recent few thousand accesses/requests.  All information may not be displayed when many 
accesses/requests are made at one time.
 f When [Access error log] and [Mail error log] exceeds a certain amount, older information is erased. fCheck [Access error log] and [Mail error...

Chapter 4 Settings — [NETWORK] menu
144 - ENGLISH
[Detail control] page
Click [Projector control] → [Detail control].
6 5
4
3
2
1
10
9
8
7
1 Control of the projector
The projector is controlled by clicking the buttons in the same 
way as the buttons on the remote control. After control, the on-
screen display of the projector at the right of the control page is 
updated.
2
 
[SUB MEMOR
 Y]
Switches the sub memory.
3
 
[SYSTEM DA
 YLIGHT VIEW]
Switches to system daylight view settings.
4
 
[FREEZE]
T...

Chapter 4 Settings — [NETWORK] menu
ENGLISH - 145
[Network config] page
Click [Detailed set up] → [Network config].
 fClick [Network config] to display the  [CAUTION!]

 screen.
 fThe current settings are displayed by pressing the [Next] button.
 fClick [Change] to display the setting change screen.
1
2
3
4
5
6
7
8
1 [PROJECT OR NAME]
Enter the name of the projector. Enter the host name if it is 
required when using a DHCP server etc.
2
 
[DHCP
  ON], [DHCP OFF]
To enable the DHCP client function, set to...

Chapter 4 Settings — [NETWORK] menu
146 - ENGLISH
[Adjust clock] page
Click [Detailed set up] → [Adjust clock].
1
2
3
4
5
6
7
1 [Time Zone]
Select the time zone.
2
 
[Set time zone]
Updates the time zone setting.
3

 
[NTP
  SYNCHRONIZATION]
Set to [ON] to adjust the date and time automatically.
4
 
[NTP
  SERVER NAME]
Enter the IP address or server name of the NTP server when 
you set to adjust the date and time manually.
(To enter the server name, the DNS server needs to be set up.) 5
 [Date]
Enter the...

Chapter 4 Settings — [NETWORK] menu
ENGLISH - 147
[E-mail set up] page
When there is a problem or the runtime of a lamp reaches a set value, an E-mail can be sent to preset E-mail addresses (up to two 
addresses).
Click [Detailed set up] → [E-mail set up].
1
2
3
4
5
6
1 [ENABLE]
Select [ENABLE] to use the E-mail function.
2
 
[SMTP
  SERVER NAME]
Enter the IP address or the server name of the E-mail server 
(SMTP). To enter the server name, the DNS server needs to be 
set up.
3
 
[MAIL
  FROM]
Enter the...

Chapter 4 Settings — [NETWORK] menu
148 - ENGLISH
8
787
9
7 [E-MAIL ADDRESS 1], [E-MAIL ADDRESS 2]
Enter the E-mail address to be sent. Leave [E-MAIL ADDRESS 
2] blank when two E-mail addresses are not to be used. 8
 Settings of the conditions to send E-mail
Select the conditions to send E-mail.
[MAIL
 CONTENTS]: 
Select either [NORMAL] or [SIMPLE].
[ERROR]: 
Send an E-mail when an error occurred in the self-diagnosis.
[LAMP1 RUNTIME]:
An E-mail message is sent when the remaining lamp on time for 
the...

Chapter 4 Settings — [NETWORK] menu
ENGLISH - 149
[Authentication set up] page
Set the authentication items when POP authentication or SMTP authentication is necessary to send an E-mail.
Click [Detailed set up] → [Authentication set up].
1
2
3
4
5
6
7
8
1 [Auth]
Select the authentication method specified by your Internet 
service provider
.
2
 
[SMTP
  Auth]
Set when the SMTP authentication is selected.
3
 
[POP
  server name]
Enter the POP server name.
Allowed characters:
Alphanumerics (A - Z, a - z, 0...

Chapter 4 Settings — [NETWORK] menu
150 - ENGLISH
Contents of E-mail sent
Example of E-mail sent when E-mail is set
The following E-mail is sent when the E-mail settings have been established.
=== P anas onic  pr ojec t or  r epor t ( CO NF I G URE )  ===
P r ojec t or  T y pe  :  DZ 870
S er ial No  :  S H1234567
-----  E-mail set up dat a -----
T EMPERAT URE WARNING  SET UP 
MINIMUM TIME at  [  60]  m inut es  int er v al 
I NT A K E  A I R T E M P E RA T URE   O v er  [  46 degC /  114 degF  ]  
E RRO...