Panasonic Digital Disk Recorders Wj Hd316 Operating Instructions

111
w[Monitor 2] Switcher function of monitor 2
Perform the settings for the switcher function of monitor
2.
●Live Sequence
The settings for Live Sequence are the same as for
Monitor1. Refer to page 109 for further information.
●Sequence Timing
The settings for Sequence Timing are the same as for
Monitor1. Refer to page 110 for further information.
Notes:
•EXT is selectable only when an external device that
can transmit a sequence signal is connected.
•The sequence changeover I/O (pin no.21) of the...

[Screenshot 2]
The camera title pop-up window will be displayed.
xMove the cursor to CAM1 using the arrows button.
[Screenshot 3]
The cursor moves to  CAM1.
cSelect a character to be entered by rotating the jog dial.
Up to 16 characters can be entered.
vMove the cursor to the right side of the entered charac-
ter using the arrows button. 
Repeat steps 3 and 4 to enter the camera title.
Notes:
•To correct the entered characters, move the cursor
to the character to be corrected and press the
STOP button to...

113
3. Move the cursor to OK using the arrows button
and press the SET button. The camera title will
be copied.
•The following characters can be entered for a cam-
era title:
0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P
Q R S T U V W X Y Z a b c d e f g h i j k l m n o p q r
s t u v w x y z À Ä Â Æ Ç É Ì Ñ Ò Ö Ù Ü Ø ß à á â ä
å æ ç è é ê ë ì í î ï ñ ò ó ô ö ù ú ü ø < > = ? ” # & ( )
* + , - . / : ; SP
[Screenshot 4]
The camera title is entered.
bPress the arrows button to move the cursor to OK...

114
●Camera Title Display
Select ON and OFF whether or not to display the camera
title.
ON:Displays the camera title.
OFF:Does not function.
●Alarm Display
Select ON and OFF whether or not to activate the alarm dis-
play at an event occurrence.
ON:Displays the alarm display at an event occurrence.
OFF:Does not function.
e[Monitor2] Settings on monitor 2 display
Perform the display settings for monitor 2 such as the
display mode (task bar style), time display position
on/off, camera title display...

115
It is necessary to adjust the communication speed and use
the same communication protocol with external devices
such as a controller when connecting those external
devices to the DATA port or the SERIAL connector
(RS232C).
It is also necessary to perform the settings for the network
such as the IP address and the gateway address when
operating this unit a PC via a network such as a LAN.
These are the descriptions of how to perform the required
settings for communication with external devices....

116
●Baud Rate
Select the communication speed for data transmission with
a connected device from the following.
2 400/4 800/9 600/19 200/38 400 bps
●Data Bit
It is impossible to change the value for this setting.
8 bit
●Parity
Select a method to check a transmission error at communi-
cation from the following.
NONE:No parity check
EVEN:Even parity
ODD:Odd parity
●Stop Bit
Select a stop bit from the following.
1 bit/2 bit
●Retry Timing
Select a retransmission interval for when data reception is
not...

117
●Baud Rate
Select the communication speed for data transmission with
a connected device from the following.
4 800/9 600/19 200 bps
●Control Camera CH
It is possible to assign camera channels to the RS485 ports
1 and 2 as shown below.
[Screenshot 1]
Start operation from the RS485 Setup menu.
zMove the cursor to Control Camera CH using the
arrows button (
CD) and press the SET button.
[Screenshot 2]
The Control Camera CH pop-up window will be displayed.
xMove the cursor to a desired cell in the TERM...

118
●Data Bit
Select a data length for communication from the following.
7/8 bit
●Parity
Select a method to check a transmission error at communi-
cation from the following.
NONE:No parity check
EVEN:Even parity
ODD:Odd parity
●Stop Bit
Select a stop bit from the following.
1/2 bit
●Retry Timing
Select a retransmission interval for when data reception is
not confirmed from the following.
OFF/100 ms/200 ms/400 ms/1 000 ms
t[NW Setup 1] Basic network settings
Perform the following basic network settings to...

119
●DNS
Select MANUAL or AUTO to enable searching an IP
address by its host name using DNS. When OFF is select-
ed for DHCP (no use of the DHCP server), select MANU-
AL and enter the domain name and the DNS server
address. If ON is selected for DHCP (use of the DHCP
server), select AUTO. When DNS is not used, select OFF.
When MANUAL is selected for DNS, enter the DNS server
address for Primary and Secondary.
●DDNS
Select ON and OFF whether or not to use the DDNS
(Dynamic Domain Name Server).
Selecting...

120
Perform the following system settings required to operate
this unit.
q[Basic Setup] Basic system settings
Perform the following settings for basic operation.
●ADMIN Password
Set the password for an administrator.
Enter 4-32 alphanumeric characters.
The same method is used to enter, insert and delete char-
acters as for attaching text information to images. Refer to
page 55 about available characters.
●PSD User
When a user operates a controller compatible with PS·Data,
operation will be restricted by...