Panasonic Dbs 824 Instructions Manual

Remote MaintenanceSystem Features6Follow the directions on the screen to access the desired programs (See
“Terminal Programming Commands 
“)Note: The Serial Interface Unit (SIU) supports three functions, 
1) Bus
IMonitor, 2) SMDR, and 3) Remote Programming However only one function
can operate at a time When not in remote programming, either SMDR or a
Bus Monitor is active When the remote programming mode is entered (by
#99xxxx), the other function stops When finished, the SMDR or Bus
Monitor function...

System FeaturesStation Class of ServiceStation Class of Service(CPC-S and CPC-M)
DescriptionStation Class of Service provides a way to restrict access to certain extension
features Station Class of Service 0 provides access to all features By default,
all extensions are assigned to this class of service Classes of Service l-8 can
be modified to allow and restrict access to specific features The following
table shows the features that can be enabled/disabled for station classes of
service
Table I-IStation...

Station HuntingSystem FeaturesStation Hunting(CPC-S and CPC-M)
Station hunting allows calls to be automatically transferred among a
preselected group of phonesWhen a call terminates to a busy extension in a hunt group, the call
automatically transfers to another extension in the group If the second
extension is busy, the call automatically transfers to another member of the
groupThree types of hunt groups are available Terminal, Distributed, and Longest
Idle In addition, a software-defined pilot...

System FeaturesStation HuntinglFF4 (Ringing and Hunt Groups) Hunt Group Pilot Number
lFF4 (Ringing and Hunt Groups) Hunt Group Transfer Timer
lFF4 (Ringing and Hunt Groups) Hunt Group Member
lFF4 (Ringing and Hunt Groups) Transfer Extensionl
FF4 (Ringing and Hunt Groups) CO Delayed Day Ring Assignments for
Hunt Groups
lFF4 (Ringing and Hunt Groups) CO Delayed Night Ring Assignments for
Hunt Groupsl
FF4 (Ringing and Hunt Groups) CO Delayed Night 2 Ring Assignments
for Hunt Groupsl
FF4 (Ringing and Hunt...

Station HuntingSystem Features
lA call arriving at the the pilot number of a hunt group will hunt to a
member that has call forwarding set, unless call forwarding is set to an
outside number The following call types will hunt to a member that has
call forwarding set- Intercom calls
- Transferred intercom calls
- Incoming CO calls
- Transferred CO calls
- DISA calls
lIn order for an extension to be permanently call forwarded to the pilot
number of a hunt group, the hunt group pilot number must be 244 or...

System FeaturesStation Message Detail Recording (SMDR)Station Message Detail Recording
(SMDR)
(CPC-S and CPC-M)
Description
Station Message Detail Recording (SMDR) provides detailed call records of
outgoing callsSMDR records can be output to a printer or an external call
accounting system Figure l-2 shows the SMDR format for the CPC-S and
CPC-M
Figure 1-2 SMDR Format CPC-S and CPC-M
0123456I012345678901234567890123456789012345678901234567~901234567~901234567~901234567
12345678 9
T BM/DD HH:WM:SS HH:MM SS...

Toll RestrictionSystem FeatureslFFl (System) SMDR Start Timer for CO Calls
l 
FFl (System) SMDR Printing Mode 1 Outbound and Inbound
lFFl (System) SMDR Printing Mode 2 Long Distance and Local Calls
l 
FFl (System) SMDR Printing Mode 3 Header Title
lFF3 (Extension) Station Message Detail Recorder (SMDR) Report
Hardware Requirements
lA printer or external call accounting system is required to output SMDR
data
Toll Restriction(CPC-S and CPC-M)
DescriptionAccess levels, including the prohibition of long...

System FeaturesToll Restriction2Local calls allowed
l-800 calls allowed
Inbound trunk calls can be answered and transferred from a Type 2 phone
Full restriction of international calls
Full restriction of operator calls
Speed dial number selectable restriction
3
Nil code selectable restriction except 911
Restriction of up to 50 sevendigit numbers
Inter-digit timing is set to 6 seconds
1 800 calls allowed
Full restriction of operator calls
Selectable restriction of international calls
SeIectable...

Trunk GroupsSystem Features
l Forced LCR Restriction
The LCR feature controls outside callsRelated Programming
lFFl (System) Override Toll Restrictions with SSD Numbers
l FF3 (Extension) Extension Lockout Code
l FF7 (Toll Restriction) Toll Restriction Settings (all)
Considerations
lThe dialing restrictions included in this feature help prevent unauthorized
outgoing calls It is possible, however, to program your system to allow
System Speed Dialing to override Toll Restrictions
Trunk Groups(CPC-S and...

System FeaturesTrunk Name AssignmentlTrunks can appear in more than one trunk group
lIf Least Cost Routing is enabled, the trunk group “9” automatically
accesses the LCR features
Trunk Name Assignment(CPC-S and CPC-M)
DescriptionYou can display a name, number, or message of up to six characters on the
LCD in place of your CO trunk line number The name will appear when a
CO call is ringing or connectedFor example, you can assign specific CO lines to different individuals or
departments Then, when an...