Panasonic Cpc+AII/B Digital Business System Release Notes Manual

Section 300~InstallationChapter 5. Peripheral Equipment
Table S-11. Maximum distrurces for SLTA installation
WiringMax. distance (in feet) betweenMax. distance (in feet) between
fF”!.Fthe DBS and SLTAthe SLTA and the SLT
AWG22300’or10n3000’or100SI
AWG24190’or10Sz1900’or100rZ
AWG 26120’ or 10 Q1200’ or 100 n
4.
5.
6.
7.
8.
9.
If the DBS is powered up, turn off the power.
Connect the GND and 
+24V leads on the SLTA to the DBS connector
panel. 
Be sure the wires do not touch each other or touch the metal...

Chapter 5. Peripheral EquipmentSection 3004nstalIation
Figure S-21. SLTA installation
To +24Von DES CN2
Connector \!c--
To GND on2DBSCN2 -Connector
QfSLTA(W-43709)
,To SLT A and B
.To SLT C and D
CN3II
T PSLT‘A’
’ SLT ’‘B
CN4
%ISLT ’
5-36DES Manual - Issued 8/l/95DBS-70-300 

Chapter 6. Double-Cabinet Systems
Two DBS cabinets can be connected in order to increase capacity. This
chapter includes connection procedures, as well as capacities for two-cabinet
systems.
See Chapter 4 for instructions on installing Tls in two-cabinet systems.
This chapter covers the following topics:
TopicPage
Guidelines6-3
Installation6-10
DBS-70-300DBS Manual - issued 8/l/956-1 

6-2DBS Manual - Issued 8/l/95DBS-70-300 

Section 300~InstallationChapter 6. Double-Cabinet Systems
Guidelines
lTwo DBS cabinets can be connected to increase line size. The maximum
line size consists of 
two DBS 96 cabinets, which provide 192 ports.
lCPC-B and SCC-B are required for two-cabinet systems.
lIf ground start or DID trunks are used in both cabinets, separate -48V
supplies must be supplied for each cabinet. 
If AECs are used in both
cabinets, separate SLT ringer boxes must be supplied for each cabinet.
lThe following table shows the...

Chapter 6. Double-Cabinet SystemsSection 300~Installation
F imre6-I. Slotusagefortwo-cabinetsvstems.DRS 40 + DRS 40
DBS 40 (Slave)
TRKl EC1 EC2 EC3 EC/TRKSCC CPC AUXl AUX2
8EC2 EC3 
EC/IRKsee CPC
Notes:
*See “Tl Interface” on page 4-11 for EC/TRK port numbers for Tl.
#A maximum of two MFR cards can be installed in a two-cabinet system. With Cable Kit
Version 1.1, one MFR is installed in the Master 
AUXl, and one MFR is installed in the
Slave 
AUXl. With Cable Kit Version 1.2, both MFR cards are installed...

Section 300~installationChapter 6. Double-Cabinet Systems
Figure 6-2. Slot usage for two-cabinet systems, DBS 72 + DBS 40
DBS40(Slave)EC3 
EC/l-RKSCC CPC AUXl AUX2
?
s
42 2
7
255;;:0
T’RKl lEC1 IEC2
DBS 72 (Master)
-IRK1IRK2EC1EC2EC3EC4EC5:C/TRK
Notes:
*A maximum of two MFR cards can be installed in a two-cabinet system.With Cable Kit
Version 1.1, one MFR is installed in the Master 
AUXl, and one MFR is installed in the
Slave 
AUXl. Wrth Cable Kit Version 1.2, both MFR cards are installed in the slave...

Chapter 6. Double-Cabinet Systems
Section 3004nstallation
F iaure6-3. Slotusdwefortwo-cabinetsvstems.DBS 72 + DBS 72
DBS 72 (Slave)
TRK TRK EC1 EC2 EC3 EC4 EC5 EC6 EC/
SCC CPC AUX AUX
12TRK12
s
74%
4
2
G
g
DBS 72 (Master)
TRK TRK EC1 EC2 EC3 EC4 EC5 EC6 EC/
SCC CPC AUX AUX1 2
TRK1 2
%
Notes:
*See “Tl Interface” on page 4-11 for EC/TRK port numbers for Tl.
Beginning with CPC-B Version 4, the EC/TRK slot in the slave DBS 72 can be used for
trunks or lines. Prior to CPC-B Version 4, this slot could only be...

Section 300~InstallationChapter 6. Double-Cabinet Systems
igure 6-4. SZot usage for two-cabinet systems, DBS 96 + DBS 40
DBS 40 (Slave)
KC CPC
-T-
EC1EC2AUX
1
AUX
2
DBS 96 (Master)
EC1EC2EC3EC4EC7 1 ECISCCICPCIAUX IAUX
Notes:
*See 
“Tl Interface” on page 4-l 1 for ECflRK port numbers for Tl.
#A maximum of twoMFR cards can be installed in a two-cabinet system. With Cable Kit
Version 1.1, one MFR is installed in the Master AUXl t and one MFR is installed in the Slave
AUXl. With Cable Kit Version 1.2, both...

Chapter 6. Double-Cabinet Systems
Section 3004nstallation
Figure 6-5. Slot usage for two-cabinet systems, DBS 96 + DBS 72DBS 72 (Slave)
DBS 96 (Master)
IRK TRK -TRK EC1 EC2 EC3 EC4 EC5 EC6 EC7 EC8 EC/SCC CPC AUX AUX
1 2 3TRK1 2
9
\o3
)r: 7.r:o\
ii
+g
Notes:
*See “Tl Interface” on page 4-l 1 for EC/TRK port numbers for Tl.
“A maximum of two MFR cards can be installed in a two-cabinet system. With Cable Kit
Version 1.1, one MFR is installed in the Master 
AUXl, and one MFR is installed in the Slave
AUXl....