Panasonic Cpc+AII/B Digital Business System Release Notes Manual

Section 300~InstallationChapter 5. Peripheral Equipment
Figure S-2. SMDR Format for CPC-AII and CPC-B Version 3.1 or higher12
3567T MM/DD HH:MM:SS HH:&!.SS NNN DDDDDDDDDDDDDDDDDDDDDDDDDDDD B9V-V&V NN
ldall typeS=Extension number
S=Inbound DISA10-69,lOO-699nextensions
sroutbound DISACO number=DISA
I=Incoming
O-OutgoingB=Dialed digits or Caller ID
T=Transfer (See Note 1.1DD=digits O-9 or symbols * or#
N=DNIS(See Note 2.)
D=DID.
‘I=Account code
O=DateAn0-9999999999
RR=month
DD=day8=Verified account code or...

Chapter 5. Peripheral EquipmentSection 300~Installation
Remote Administration Interface (RAI)
Guidelines
lThe RAT is a modem card that installs on the XC card. The card is used to
remotely administer the system through a trunk line.
lTwo versions of the RAI card are available. Both versions use 1 Stop bit, 8
data bits, and no parity. The RAI-A card has a fixed baud rate of 300. The
RAI-B card supports both 300 and 1200 baud operation. The following
table shows the transmission rate of each card along...

Section 300~InstallationChapter 5. Peripheral Equipment
gure 5-3. RAI connection
RAI-A(VB-43706): 300 bps
RAl-B(VE43707)oriO0 or 1200 bpa
sob attmurtbn bvel.llm attenuation b therum of the ‘ON’ aettlnga.DES-70-300DBS Manual 
- Issued WV955-7 

Chapter 5. rerlpnerat Equipmentsection 300~Installation
Background Music/Music-On-Hold
Guidelines
lA single music source can be used for both background music (BGM) and
music-on-hold (MOH), or separate music sources can be used for each
feature.
lIf a single music source is used for both MOH and BGM, the music source
connects to CN5 on the Connector Panel. If separate sources are used, the
MOH source connects to CN5, and the BGM source connects to the BGM
connector on the SCC card.
lIf an FM radio is...

Section 300~InstallationChapter 5. Peripheral Equipment
Note: To change the volume levels of the music sources, adjust the
variable resistors on the SCC card.
Table 5-3. SCC variable resistors
Variable Resistor
ISCC-AI
Adjusts CO ringing tone volume.
( Adjust MOH and BGM volume.
VRlvR2
VR6
SCC-B
Adjusts MOH volume.
Adjust BGM volume.
Adjusts CO ringing tone volume.
Figure 5-4. Znstilation of music-on-hold and backwound music
RadioBGM only
Earphcne
Jack
IRadioBGMConnectort-
-see...

Chapter 5. Peripheral EquipmentSection 300~Installation
Off-Premises Adaptor (OPX)
Guidelines
lAnalog phones can be connected as off-premise stations through a direct
line to the DBS or through the central 
office, depending on how far the
stations are from ‘the OPX Adaptor.Table 5-4 shows how far the OPX stations can be from the adaptor without
going through a CO.
Table 5-4.Maximum distances for direct connection to OPX stations
Wiring
PW
Max. distance (in feet) between
the OPX Adaptor and the OPX...

Section 3004nstallationChapter 5. Peripheral Eauioment
Installation
The following procedures describe direct OPX connection and OPX
connection through a CO. Order an 
OL13C circuit for an OPX through a CO.
Refer to Figure 5-6 on page 5-13 when installing the OPX.
Installing an OPX Station Without Going Through a Central Office
1.Remove the cover from the OPX Adaptor.
2.Remove the cable punch-out plate (Figure 5-12) to make an opening for
the cables coming into the OPX Adaptor.
To remove the plate, cut...

Chapter 5. Peripheral EquipmentSection 300~Installation
4.Connect the “R” and “T” leads to a digital extension port on the DBS.
5.Connect the “GND” lead on the OPX Adaptor to the DBS Frame Ground
screw.
6.Connect the “TR” and “‘IT” leads to the OPX station.
7.Install the cover on the OPX Adaptor.
8.Turn the system off and back on, or unplug the cable connected to the
digital extension and then plug it back in.
Installing an OPX Station Through a Central Office
1.Perform Steps 1 through 5 of “Installing....

Section 300-InstallationChapter 5. Peripheral Equipment
Fimre S-6. OPX installation
To a DBS(0digital line
Poti
(Terminals
for externalE-RG+ringing 
SOUrCe) E-RG-
To the DBS
Frame Ground
TR
TT
screwI
CN3
Off-Premise
Extension Adaptor(VB-43702)To off-premise
SLT or _demarcation
block
DBS-70-300DBS Manual - Issued 8/l/955-l 3 

Lnaprer 3. rer~prlural cqulpmenr
Paging
The DBS allows extensions to be grouped into paging groups numbered OO-
07. When you issue a page (by dialing #IO-#07), you specify a paging group,
so that your announcement is heard over the key telephones and Digital
Single Line Telephones that are members of that group. Paging groups often
include people whose work is related.
Extelnal zone paging allows you to connect up to five speaker groups to the
DBS. Each speaker group is assigned to one of five paging...