Panasonic Aj Spd850p Operating Instructions Manual

71
Error messages (continued)
“WARNING ” information display
•A warning message is displayed whenever a warning occurs.
When warnings have not been detected,  “NO WARNING ” is displayed.
• When multiple warning occur, the descriptions for each warning can be ch\
ecked by turning the search dial.
If  “T&S&M ” is selected in the setup menu No. 008 (DISPLAY SEL), a message appear\
s in the mode display whenever a
warning or error occurs. When multiple events occur, the event with the highest priority is...

72
TURN POWER OFF   Displayed when trouble has occurred in reading data from the card or
writing data onto the card. To continue operation, turn the power off an\
d
then back on.
E-30
stop
Error messages (continued)
Message
Error
Description
No. Deck
operation
COMM ERROR    Displayed when the orders issued by the system control command have
not been followed even after 3 seconds have elapsed. To continue
operation, turn the power off and then back on.
E-37
stop
SYSTEM ERROR   Displayed when trouble has...

73
“HOURS METER ” information display
Turn the search dial to move the cursor ( ). The description for the item where the cursor is located is shown on\
 the
counter display.

Item Description
No.
Counter display

Displays the deck’s serial No.
Ser
OPERATION Displays the time that the power has been supplied in one-hour
units.
H00
0H - 99999H
LCD ONDisplays the time during which the LCD monitor has been
lighted in 1-hour increments.
H20
0H - 99999H
POWER ONThe number of times the power has been turned...

74
The underlining indicates the factory settings.
Any changes to the settings can be made using the
setup menu items listed below.
RS-232C interface
The memory card recorder can be operated by commands
when the RS-232C interface is used.
(See command table on pages 75, 76)
Conditions for acknowledging commands
from RS-232C interface
• The front panel REMOTE button is lit
• The setup menu No. 204 (RS232C SEL) must be ON.
If the above conditions are not met, [ACK] + [STX] ER001
[EXT] is returned to the...

75
SHTL
FORWARD[STX] OSF:data [ETX] \b[STX] OSF [ETX]
This is the forward direction shuttle
command.
data = n : speed data 0 : STILL
1 : 
×0.03
2 : 
×0.1
3 : 
×0.2
4 : 
×0.5
5 : 
×1
6 : 
×2
7 : 
×4
8 : 
×8
9 : 
×16
A : 
×32
Note:
The x16 and x32 speed differ according to
the setting selected for setup menu No. 101
(SHTL MAX).
SHTL
REVERSE [STX] OSR:data [ETX] \b[STX] OSR [ETX]
This is the reverse direction shuttle
command.
data = n : speed data 0 : STILL
1 : 
×0.03
2 : ×0.1
3 : ×0.2
4 : ×0.5
5 : ×1
6 :...

76
RS-232C interface (continued)
Commands relating to inquiries
Notes:•As for the return (completion) message, [ACK] is
first returned when data is received, and the
execution message is subsequently returned. It is
only the execution message which is listed in this
table.
• In the case of commands not listed in the table,
ER001 (invalid command) is returned after [ACK]
has been returned.
CTL/TC
DATA
REQUEST [STX] QCD [ETX] \b[STX] CD data [ETX]
This command is for inquiring about the
counter value....

77
Connector signals
VIDEO IN
SDI IN 
(DIGITAL)
Y, PB, PR
(ANALOG)
VIDEO IN
REF VIDEO
INBNC × 2, Active through
(Board, option)
BNC 
× 3 
(Board, option)
BNC 
× 2, Loop-through,
75  Ωtermination switch provided 
BNC 
× 2, Loop-through,
75  Ωtermination switch provided
RS-422A REMOTE (9P)
(REMOTE)
Pin No.
1
2
3
4
5
6
7
8
9 Signal
FRAME GROUND
TRANSMIT A
RECEIVE B
RECEIVE COMMON
—
TRANSMIT COMMON
TRANSMIT B
RECEIVE A
FRAME GROUND
RS-232C
D-SUB 25-pin (crossover cable supported)
Pin No.
1
2
3
4
5
6
7
20...

78
Specifications
Power supply: AC 100 – 240 V, 50 / 60 Hz
Power consumption: 
80 W, 105 W (with all options)
Operating ambient temperature:
5 °C to 40  °C
Operating ambient humidity: 10 % to 80 % (no condensation)
Mass: 15 kg (30.8 lb)
Dimensions (W x H x D): 424 mm x 175.2 mm x 430 mm
(16 3/4 inches x 6 15/16 inches x 16 15/16 inches)
(Not including the support legs, connectors, and
SEARCH dial)
Recording format: DVCPRO50/DVCPRO/DV format selectable
Recording video signal: 525i/625i system selectable...

79
Specifications (continued)
AUDIO
Digital Audio
Sampling frequencies:48 kHz (synchronous with video)
Quantizing: 16 bits
Frequency response: 20 Hz to 20 kHz ±1.0 dB (at the reference level)
Dynamic range: Better than 90 dB 
(1 kHz, emphasis OFF,  “A ” weighted)
Distortion: Less than 0.05% 
(1 kHz, emphasis OFF, reference level)
Crosstalk: Less than  –80 dB (1 kHz, between 2 channels)
Headroom: For AJ-SPD850P: 20 dB
For AJ-SPD850E: 18 dB
De-emphasis: T1 = 50 µsec, T2 = 15 µsec (auto on/off)
Audio Input...

Information on Disposal for Users of Waste Electrical & Electronic Equip\
ment (private households)
This symbol on the products and/or accompanying documents means that use\
d electrical and electronic productsshould not be mixed with general household waste.
For proper treatment, recovery and recycling, please take these products\
 to designated collection points, where they
will be accepted on a free of charge basis. Alternatively, in some count\
ries you may be able to return your products
to your...