Panasonic Aj Spd850p Operating Instructions Manual

21
Jog/Shuttle (Search dial)
(1) Press the search dial so that it remainspressed in
Check that the JOG lamp lights.
(2) Turn the search dial
The dial ’s click-stops are released, and the card data is
played back at the speed ( –1x to +1x) corresponding to
the speed at which the dial is turned.
When you stop turning the dial, a still picture is shown.
(3) To transfer the memory card recorder from the jog mode to another mode, press the button
corresponding to the mode
Note:
The factory setting is that...

22
Working with clip thumbnails
A clip is a piece of data containing video and audio from a single video\
 recording, as well as additional information
such as voice memos and meta-data. 
This unit allows the following operations to be performed using the sear\
ch dial, FF button, REW button, SHIFT
button and SET button while you are checking out the thumbnails of clips\
 displayed on the LCD monitor.• Playing, deleting, and repairing clips
• Adding/removing shot marks to/from clip thumbnails
• Playing...

23
Working with clip thumbnails (continued)
Thumbnail screenPress the THUMBNAIL button to display the thumbnail
screen on the LCD. Press the THUMBNAIL button again
to return to the normal display. 
Press the MENU BAR button on the thumbnail screen to
change the pointer to a menu bar. In this state, menu
actions can be performed on thumbnails.
Thumbnail selection operationsMultiple thumbnails can be selected as desired on the
thumbnail screen.
(1) Use the search dial to move the pointer (yellowbox) to...

24
Working with clip thumbnails (continued)
Menu bar
The menu bar contains menu items for performing clip
operations, switching/setting the thumbnail display, etc.
To use the menu bar, press the MENU BAR button on
the thumbnail screen. Menu items are selected with the
search dial, FF button, REW button or SET button. 
THUMBNAIL :This menu is used to switch the
thumbnail display or set the display
method.
OPERATION : This menu is used to delete clips and
format P2 cards.
PROPERTY : This menu is used to...

25
Working with clip thumbnails (continued)
Switching the thumbnail display
It is possible to switch the thumbnail screen so that only
clips meeting certain conditions are displayed.
(1) Press the THUMBNAIL button.
The thumbnail screen is displayed on the LCD.
(2) Press the MENU BAR button.
The pointer moves to the menu bar.
(3) Move the pointer to THUMBNAIL, and thenpress the SET button to select it.
A submenu is displayed. Select one of the submenu
options to switch the thumbnail display.
ALL CLIP:...

26
Working with clip thumbnails (continued)

Voice memos
A voice memo is audio data which is separate from the
original recorded audio and can be added to a clip
independently of the original recorded audio. Voice
memos added using a camera recorder can be played.
Playing voice memos
(1) Press the THUMBNAIL button. 
The thumbnail screen is displayed on the LCD. 
(2) Press the MENU BAR button.
The pointer moves to the menu bar.
(3) On the menu bar, select [THUMBNAIL], then select [VOICE MEMO CLIPS].
Clip...

27
Working with clip thumbnails (continued)
Repairing clips 
This section describes how to repair bad clips which were
have been damaged for reasons such as a sudden
power outage during recording. 
(1) Press the THUMBNAIL button. 
The thumbnail screen is displayed on the LCD. 
(2) Use the search dial to move the pointer to theclip you want to repair (if a clip is bad, it has a
bad clip mark on it).
(3) Press the SET button to select the clip. 
(4) Press the MENU BAR button. On the menu bar, select...

28
Working with clip thumbnails (continued)
Thumbnail display settings
Thumbnail display options can be customized as suitable
for the intended use.
(1) Press the THUMBNAIL button.
The thumbnail screen is displayed on the LCD.
(2) Press the MENU BAR button.
The pointer moves to the menu bar.
(3) On the menu bar, select [THUMBNAIL], then[SETUP].
The following screen is displayed.
MARKER IND.: Toggles the shot mark indicator display ON/OFF. The
default setting is display ON.
VOICE MEMO IND.: Toggles the...

29
From the menu bar, select [OPERATION]  →[DEVICE
SETUP]  →[META DATA]  →[USER CLIP NAME] item.
Either [TYPE1] or [TYPE2] can be selected as the USER
CLIP NAME recording method.
[TYPE1]
[TYPE2]
1  Concerning the COUNT value
The COUNT value is indicated as a 4-digit number.
When the clip metadata has been loaded and [TYPE2]
has been selected as the recording method, the COUNT
value is incremented by 1 each time a shot is taken and a
new clip is generated.
It can be reset by following the sequence of...

30
Clip number 
Thumbnail
Clip information
Various indicators added to the clip, and the number
of added voice memos are displayed. If the P2 card
containing the clip is write-protected, a  mark is
also displayed in this area. Slot number

Working with clip thumbnails (continued)
Example: IP 192.168.000.002 MASK 255.255.255.000
GATE 192.168.000.xxx
“ xxx ” must be a value which does not exist on the
network connected.
DVD settings (optional)
Set whether to use the DVD drive. When not using the
DVD drive...