Panasonic Aj Spd850p Operating Instructions Manual

61
Setup menus (continued)
Number of lines which can be set for TELETEXT
•When 25 Mbps is the recording/playback format.
No. 800: 
ADD LINE 
25 setting value Number of lines which can be set
[525i system] [625i system]
660:
UMID REC setting value
660:
UMID REC setting value
OFF ON OFF
ON
OFF
YC422
YC411
Y1_B/W
Y1_BPF
C1
Y2_B/W
Y2_BPF
C2
13
5
8
13
5
10
4
5
10
4
14
7
10
14
7
12
5
8
12
5
• When 50 Mbps is the recording/playback format.
No. 801: 
ADD LINE 
50 setting value Number of lines which can be set...

62
Setup menus (continued)
No./Item Description
USER menu 
A00
LOADThis selects the user file whose
contents will be loaded into USER1.
0000
USER2: 
The USER2 file contents are loaded.
0001 USER3 : The USER3 file contents are loaded.
0002 USER4 : The USER4 file contents are loaded.
0003 USER5 : The USER5 file contents are loaded.
Note:
When the SET button is pressed after
loading, the setting will be stored in the
memory. When the MENU button is
pressed, the setting will not be changed.
A01
SAVE This...

63
Time code, user bit and CTL
Time code
The time code is used when the time code signal generated
by the time code generator (time code signal generator) is to
be recorded.
The time code values are indicated using the display
and superimpose functions.TCR 00 : 07 : 04 : 24 ↑↑↑↑
Hours Minutes Seconds Frames
User bit
“ User bit ” refers to the 32-bit (8-digit) data frame among the
time code signals which has been released to users. It
enables operator numbers values to be recorded.
The alphanumeric...

64
Superimpose screen
The control signals, time code, etc. are displayed using
abbreviations.TV monitor

TCR:::
TCR:::TCR:::

Abbreviations:
CTL :Control signal count value
TCR : Time code data recorded in the SBC area
UBR : User bit data recorded in the SBC area
TCG : Time code data of the time code generator
UBG : User bit data of the time code generator
Note: “TR ” or  “UR ” appears when the data could not be
read properly from the card.

Characters displayed
The background of characters superimposed...

65
Video output signals and servo reference signal
This section explains how the output signals and servo
reference signal are selected.
External synchronization of video output signals
The video output signals are output in synchronization with
the REF VIDEO input signal or video input signal.
As shown in the figure below, this signal is selected in
accordance with the setup menu settings, deck mode and
availability of the video input signal.Notes:
Synchronization is determined as follows depending
on...

66
Audio V fade function
When the settings below are selected for audio processing
between clips or events (setup menu No.727: PB FADE) at
times such as during clip selection and playback or play list
playback, V fade or cut processing is performed for these
sections during playback.
The clips recorded over a multiple number of P2 cards and
the clips created by edit copying are shown in the figure
below.Clips extending over more than one P2 card or
automatically divided and recorded clips using a P2...

67
Monitor output channel
The monitor output channels are selected using the
MONITOR SELECT and MONITOR MIX button as shown
below.
Audio recording channel and monitor output selection
Audio recording channel
The audio is selected as shown below by using the
AUDIO MIX switch, REC CH1/CH3 and REC CH2/CH4
buttons on the front panel.
Recordingtrack
CH1
CH2
CH3
CH4Recording signal
CH1 input/CH2 input/CH1 input+CH2 input
CH1 input/CH2 input/CH1 input+CH2 input
CH3 input/CH4 input/CH3 input+CH4 input
CH3...

68
Rack mounting
The memory card recorder can be mounted into a 19-inch
standard rack using the optional rack-mounting adaptors
(AJ-MA75P).
For the installation rails, it is recommended that the 18-inch
rail and bracket (model number CC3061-99-0400) by
Chassis Trak be used. (The complete slide rail and bracket
deck is not available from Panasonic.)
For further details, consult your dealer.
(1) Attach the inner members of the slide rails
Refer to the figure below for the locations where the
screws are to...

69
Condensation
Condensation occurs due to the same principle involved
when droplets of water form on a window pane of a heated
room. It occurs when the deck or card is moved between
places where the temperature or humidity varies greatly or
when, for instance:
•It is moved to a very humid place full of steam or a room
immediately after it has been heated up.
• It is suddenly moved from a cold location to a hot or humid
location. When moving the deck to locations such as these, leave it
standing for...

70
Error messages
When a warning occurs in this unit, the error number is
indicated on the counter display.
Open the DIAG menu to display a description of the error on
the counter display or monitor TV. When an operational
malfunction has occurred in the unit, the error number flashes
on the counter display.
DIAG menu
This displays the deck information.
Deck information includes “WARNING ” information,
“ HOURS METER ” (usage time) information and  “UMID
(Unique Material Identifier) ” information.
A DIAG...