Oce ColorWave 600 User Manual

The toner states
#
Description
Icon
Toner OK Toner low, empty or cartridge not present.
Chapter 5
 - Use the printing system 171The system monitor and the system states
Downloaded From ManualsPrinter.com Manuals 

Control the printer
Switch on or switch off the printer
How to switch on or switch off the printer
#
Illustration
On / off switch.
'On / Off switch' [19]The 'On / Off switch' at the front side of
the printer.
Use 
this switch in your daily work to
switch
 
on and switch off the printer. The green main power switch at the rear
side 
of the printer.
Use 
this switch only if you must connect
or disconnect the mains supply of the
printer.
To disconnect

 the mains supply:
• Use 
the green...

Pause or resume the printer
Introduction
If you do not want the printer to start printing you can pause the printer. If the printer
can 
start printing again you can resume the printer.
How 
to 'Pause' or 'Resume' the printer #
Remarks
Action To pause the printer:
In 

the 'Queue' screen use the 'Lower left softkey' key on the
printer operator panel to pause the printer.
The 
following message is displayed.
• 'Printer pause
 requested'
• 'The 

printer stops...

Solve problems with the printer
Introduction
Introduction
If there is a problem with the printer that the operator can solve, the printer operator
panel displays
 the following message. Please follow the instructions on the printer operator panel step by step. For additional
information about

 some instructions or the location of specific covers or doors, please
refer to

 the following modules:
• ‘Cover or

 door opened’  
on page 175.
• ‘Pull
 up 
the 'Top delivery tray' and open the 'Top...

Cover or door opened
Introduction
The media drawers and certain covers must only be opened if you are asked to do so in
a
 wizard on the printer operator panel.
Attention:
When you open one of the indicated covers or drawers while you are not in a wizard, the
system produces a warning signal. The red LED on the printer operator panel illuminates.
Attention:
When you open one of these covers or drawers during printing, the printer stops and the
printer operator panel shows one of the warnings that are...

Position of the component
Displayed warning
'Front cover' [6]
Note:
Normally you open the front cover in case
of a media jam. 'Top cover' [14]
Note:
Normally you open the top cover in case
of
 a media jam, to 
check the guide flap
(see
 
‘Check and clean the guide flap’  on
page  184
) or to check the print surface (see
‘Check and clean the print surface’  on page
181
). Chapter 5
 - Use the printing system176Cover or door opened
Downloaded From ManualsPrinter.com Manuals
6  
14   

Position of the component
Displayed warning
'Top back cover' [9]Note:
Normally you open the top back cover in
case 
of a media jam. Chapter 5
 - Use the printing system 177Cover or door opened
Downloaded From ManualsPrinter.com Manuals
9   

Pull up the 'Top delivery tray' and open the 'Top cover'
How to pull up the 'Top delivery tray' and open the 'Top cover'
#
Illustration
Action Pull up the left part of the top
delivery tray.
1 Lock 
the left part of the top de-
livery
 tray with the metal locking
mechanism.
Repeat step 1 and 2 for the right
part 
of the top delivery tray.
2 Open the 'Top cover'.3
Chapter 5
 - Use the printing system178Pull up the 'Top delivery tray' and open the 'Top...

Illustration
Action ‘Check and clean the print surface’
on page 181 [1] or ‘Check and
clean 
the guide flap’ on page  184
[2]. 4
Chapter 5
 - Use the printing system 179Pull up the 'Top delivery tray' and open the 'Top cover'
Downloaded From ManualsPrinter.com Manuals 

Close the 'Top cover' and flap back the 'Top delivery tray'
If you are ready
#
Illustration
Action Close the 'Top cover'.
1 Unlock the metal locking mech-
anisms of the left and the right
part of the top delivery tray.
2 Flap 
back the left part and the
right part
 of the top delivery.
Note:
If the left part and the
right 
part of the top de-
livery tray are not in the
same position, you can
adjust

 the top delivery
tray.

 (see  ‘Adjust the 'Top
delivery 
tray'’  on...