Oce ColorWave 600 User Manual

Check and clean the print surface
Introduction
This document describes how to check and clean the print surface.
When 
to do When a media jam occurs or when there is pollution on your printed output, one of the
steps 
to solve the problem is to clean the print surface.
Required 
tool
• Clean 
card
Illustration [207]
 Clean card
Chapter 5
 - Use the printing system 181Check and clean the print surface
Downloaded From ManualsPrinter.com Manuals 

How to check and clean the print surface
#
Illustration
Action Remove the top delivery tray and
open the 'Top cover'.
(see 
‘Pull up 
the 'Top delivery
tray'
 and open the 'Top cover'’  on
page 178)
1 Check if toner drops are 
on the
print surface.
2 Remove the toner with the clean
card. 
The pollution should be
removed
 from the print surface,
into the direction of the 'Top left
cover'. You can find 
the clean
card 
in the clean card holder at
the 
underside of the...

Illustration
Action Check if the holes in the print
surface are
 open.
If

 not: Use 
the pin of the clean
card 
to open the holes.
4
Put back
 the clean card 
in the
clean 
card holder.
5 Close the top cover and replace
the top

 delivery tray.
(see  ‘Close

 the 'Top cover' and flap
back the 'Top delivery 
tray'’  on
page 180) 6
Chapter 5
 - Use the printing system 183Check and clean the print surface
Downloaded From ManualsPrinter.com Manuals 

Check and clean the guide flap
Introduction
This document describes how the check and clean the guide flap.
When
 to do When a media jam occurs or when there is pollution on your printed output, one of the
steps 
to solve the problem is to clean the guide flap.
Required
 tool
• Clean 
card
Illustration [213]
 Clean card
Chapter 5
 - Use the printing system184Check and clean the guide flap
Downloaded From ManualsPrinter.com Manuals 

How to check and clean the guide flap
#
Illustration
Action Remove the top delivery tray and
open the 'Top cover'.
(see 
‘Pull up 
the 'Top delivery
tray'
 and open the 'Top cover'’  on
page 178)
1 Check if the guide flap is pollut-
ed with toner.
2 Remove the toner pollution with
the clean card 
from the guide
flap. 
The pollution, which is
dislodged, should
 be removed
from 
the print surface, into the
direction
 of the 'Top left cover'.
You can find 
the clean card in...

Illustration
Action Close the top cover and replace
the top
 delivery tray.
(see  ‘Close

 the 'Top cover' and flap
back the 'Top delivery 
tray'’  on
page 180) 5
Chapter 5
 - Use the printing system186Check and clean the guide flap
Downloaded From ManualsPrinter.com Manuals 

Adjust the 'Top delivery tray'
Introduction
This document describes how to adjust the 'Top delivery tray'.
When 
to do When you want 
to prevent printed output from curling.
Required
 tool
• Cross 
screwdriver
Illustration How to adjust the Top delivery tray
#
Illustration
Action Pull 
up the metal guide of the
'Top delivery
 tray'. 1
Chapter 5
 - Use the printing system 187Adjust the 'Top delivery tray'
Downloaded From ManualsPrinter.com Manuals 

Illustration
Action Use your finger or the cross
screwdriver 
to adjust the position
of the metal guide (both 
sides).
2 Flap 
back the metal guide to
check
 if the adjustment is cor-
rect.
3 Repeat step 1 to 3 for the second
metal guide.4
Chapter 5
 - Use the printing system188Adjust the 'Top delivery tray'
Downloaded From ManualsPrinter.com Manuals 

Illustration
Action Check if both metal guides are
in the same position and run
parallel 
to the top delivery plates
below the guides. Adjust the po-
sition if necessary. 5
Chapter 5
 - Use the printing system 189Adjust the 'Top delivery tray'
Downloaded From ManualsPrinter.com Manuals 

Cut the media
Introduction
When a media jam occurs, one of the steps to solve the problem is to cut the jammed
media. The
 printer operator panel displays the following message. How to cut the media
#
Illustration
Action Use 
your right hand to push
down the metal plate that guides
the media. Use your left hand to
cut 
the media from left to right
with
 
the knife behind the front
cover.
1
Again, push
 down the metal
plate 
that guides the media to
place 
the knife back into the
original
 
position. 2...