Oce ColorWave 600 User Manual

Configure the 'Media request time-out'
Introduction
The printer operator panel displays a media request when a media is requested that is not
available on the printer.• When the
 'Media request time-out' setting is disabled, the media request will be dis-
played 
on the printer operator panel until it is resolved.
• When 
the 'Media request time-out' setting is enabled (default), you can enter a media
request time-out value in seconds. If the media request is not resolved within...

Configure the 'Printer panel time-out'
Introduction
The printer operator panel can automatically return to the Home screen. When this setting
is disabled, the panel never returns to the Home screen automatically.Note:
When enabled, the printer operator panel returns to the Home screen when the keys
and the
 scroll wheel are 
not activated during the specified time-out period. When to do
Enable the setting and define a suitable time-out period that does not interfere 
with the
print productivity....

Configure the energy save modes of the Océ ColorWave 600
Introduction
The Océ ColorWave 600 offers two energy save modes that you can set if the printer is
idle 
for a defined period. The configuration of the timers prevents unnecessary power
consumption. 
You can adjust the value of the timers.
When 
to do Sleep mode timer (Default value 1 
hour).
The 
Océ ColorWave 600 uses minimal energy, because the power supply of the printer
is turned
 off. The power supply of the embedded Océ ColorWave 600...

Note:
When the Océ ColorWave 600 is in the energy save mode, there are two ways to activate
the system.• press a

 key on the printer operator panel.
• send 
a job. Chapter 4
 - Configure the printing system124Configure the energy save
 modes of the Océ ColorWave 600
Downloaded From ManualsPrinter.com Manuals 

Configure the media sizes
Introduction
You must indicate in the Océ Express WebTools the following settings.
• The 
core size of the media rolls
• The 
media sizes How to define the core size of the media
Attention:
Access the Océ Express WebTools. This setting is editable for the Key operator and the
Power user. 1.
Navigate 
to 'Configuration' - 'Printer setup'.
2. Click 
'Edit' in the 'Media' bar or click the value of the 'Two-inch core used' setting if
you 
also...

#
Media sizes
Media series
42x60 inch, E, D, C, B.
'ANSI small'
42x60
 inch, E+, A0, B1, A1, B2, A2, A3
'DIN'
42x60
 inch, F+, E+, E, D+, D, C+, C, B+, B.
'ANSI
 mixed'
42x60
 inch, 500x700 mm, 700x1000 mm, 800x1189 mm, A0,
A1, A2, A3, B0, E+.
'DIN

 Carto'
...
'Custom'
Note:
You cannot disable media sizes that are currently loaded on the printer.
Note:
When you load a media roll the printer automatically detects the roll width. If the detected
roll width is not a...

The 'Configuration' tab in the Océ Express
WebTools
Configure the network settings in the Océ Express WebTools
Introduction
Some of the network settings are configured during the installation of your system. If
you 
want to change the initial configuration or if you want to define more network settings,
you 
can do so in the 'Configuration' - tab.
How 
to configure the network settings in the Océ Express WebTools 1. Click 
'Configuration' - 'Connectivity'.
2. Click...

Set the 'Network duplex mode'
Introduction
Use the Océ Express WebTools to set 'Network duplex mode' for your network adapter.
The list of values you can select depends on the type of network card.
Before
 you begin This 
setting is editable for the System administrator or Power user.
How 
to set the 'Network duplex mode' 1. Click 'Configuration' - 'Connectivity'.
2. Click 

'Edit' in the 'Network adapter' bar or click the value of the 'Network...

Set the 'Network speed'
Introduction
Use the Océ Express WebTools to set 'Network speed' for your network adapter.
The 
list of values you can select depends on the type of network card.
Before
 you begin This 
setting is editable for the System administrator or the Power user.
Attention:
Gigabit ethernet (1000 Mbit/s) is supported, but only by automatic detection.
How to set the 'Network speed'
1.Click 
'Configuration' - 'Connectivity'.
2. Click 
'Edit' in...

Relevant settings on the printer operator panel
Change the display language of the printer
Introduction
The Océ Express WebTools allows you to define the 'First language' (the default display
language) and the 'Second language' (the alternative display language) for the printer
operator panel.
The 

'First language' and the 'Second language' you defined in the Océ Express WebTools
are 
also the display languages that are available on the printer operator panel. You can...