Nitsuko Ds2000 Software Manual

0300 - System Options
0302 - System Identification
DS2000 Software Manual Chapter 2: Programming373
Telephone Programming Instructions
1. Enter the programming mode.
2. 0302 + 
HOLD
3. Enter the system name (up to 14 characters) + VO L .
(Refer to Programming Names and Text Messages on page 361 if you need help in entering 
names)
OR
Press 
VO L  to scroll to the next option.
After pressing 
VO L  to scroll to the next entry, you can press CONF to exit the pro-
gram.
4. Enter the site phone number (up...

0300 - System Options
0302 - System Identification
374Chapter 2: ProgrammingDS2000 Software Manual
OR
Press 
CONF to exit the program. 

0400 - Timers
0401 - System Timers
DS2000 Software Manual Chapter 2: Programming375
0400 - Timers
0401 - System Timers
Description
Use Program 0401- System Timers to enter the values for system-wide timers. Conditions
NoneLCCPU 01.00.00 Available.
Table 22:  Program 0401 - System Timers
OptionDescriptionEntriesDefault
Park Orbit
Use this timer to set how long a call stays in 
System Park Orbit before it recalls the exten-
sion that parked it. This timer if for orbits 
60-67 only. The recall for orbits...

0400 - Timers
0401 - System Timers
376Chapter 2: ProgrammingDS2000 Software Manual
Dialing PauseFor Automatic Route Selection, the system 
waits this interval when it encounters a 
pause in an ARS Dial Treatment.
• See Automatic Route Selection on 
page 34 for more.
For Speed Dial, the system waits this inter-
val when it encounters a pause in a Speed 
Dial bin.
• See Speed Dial on page 263 for more.DIALING PAUSE?1-9999 sec.
0 = Disabled1 sec.
Page DurationUse this timer to set the maximum length of...

0400 - Timers
0401 - System Timers
DS2000 Software Manual Chapter 2: Programming377
Telephone Programming Instructions
1. Enter the programming mode.
2. 0401 + 
HOLD
3. Enter data for the displayed timer + HOLD.
OR
Press 
VO L  or VO L  to scroll to the timer you want to change + HOLD
4. Enter data for the displayed timer + HOLD
5. Press VO L  or VO L  to scroll to another timer.
OR
Press 
HOLD to return to step 2 and enter another program number.
Centrex Type  Feature 
Key DelayThis timer sets how...

0400 - Timers
0402  - Trunk Timers
378Chapter 2: ProgrammingDS2000 Software Manual
0402  - Trunk Timers
Description
Use Program 0402- Trunk Timers to enter the values for trunk timers.Conditions
NoneLCCPU 01.00.00 Available.
Table 23:  Program 0402 - Trunk Timers
OptionDescriptionEntriesDefault
Camp-On
• Information to be provided.CAMP ON?0-9999 sec.60 sec.
Line ResponseWhen the system fails to detect loop current 
on a trunk, it will wait this interval before 
marking the trunk as defective.
Be sure...

0400 - Timers
0402  - Trunk Timers
DS2000 Software Manual Chapter 2: Programming379
PBX/Centrex FlashUse this timer to set the Flash interval. When 
a user flashes a trunk, the system opens the 
trunk circuit for this interval. For accurate 
flash function, be sure to set this interval for 
compatibility with the connected telco or 
PBX/Centrex.
If you set this interval too short, the telco 
may not always register the flash. If too long, 
inadvertent disconnects may occur.
• See Flash on page 132 for...

0400 - Timers
0402  - Trunk Timers
380Chapter 2: ProgrammingDS2000 Software Manual
Minimum Ring Detection 
TimerUse this timer to set the threshold for ring 
detection. If the ring signal is longer than 
this interval, the system interprets the signal 
as valid ringing. If the signal is equal to or 
shorter than this interval, the system ignores 
the ringing.
Be sure the value you enter is compatible 
with the local telco. If you set this value too 
short, the system may detect line spikes and...

0400 - Timers
0402  - Trunk Timers
DS2000 Software Manual Chapter 2: Programming381
Manual DTMF Tone OnThis timer sets the duration of DTMF digits 
for trunk calls manually dialed by an exten-
sion user. This is required because the sys-
tem buffers the digits the user dials.
Set this timer for compatibility with the con-
nected telco or PBX/Centrex. If you set this 
interval too short, the telco or PBX/Centrex 
may not be able to properly detect the 
DTMF digit. If too long, outbound dialing is...

0400 - Timers
0402  - Trunk Timers
382Chapter 2: ProgrammingDS2000 Software Manual
Speed Dial DTMF Tone 
OffThis timer sets the duration the quiet time 
between DTMF digits for Speed Dial trunk 
calls automatically dialed by the system. 
Set this timer for compatibility with the con-
nected telco or PBX/Centrex. If you set this 
interval too short, the telco or PBX/Centrex 
may not be able to set up to receive the next 
DTMF digit. If too long, outbound dialing is 
unnecessarily slowed down.
• See Speed...