Nitsuko Ds2000 Software Manual

0400 - Timers
0402  - Trunk Timers
DS2000 Software Manual Chapter 2: Programming383
Far End DisconnectUse this timer to set the loop disconnect 
interval for trunk calls. If the system detects 
a loop current interruption longer than this 
interval it assumes the telco has discon-
nected the trunk. It then returns the trunk 
trunk to idle.
Set this interval for compatibility with the 
connected telco or PBX/Centrex. If you set 
this interval too short, the system may inad-
vertently disconnect valid...

0400 - Timers
0402  - Trunk Timers
384Chapter 2: ProgrammingDS2000 Software Manual
Caller ID Detection TimerCaller ID is currently not available. Do not 
change this timer from its default setting.
The Caller ID Timer is the amount of time a 
system DSP is turned on, “listening” for 
Caller ID digits on a trunk. The listen mode 
starts 100 mS after the first ring burst and 
continues until the AC Impedance Timer 
times out. Only change this timer is you are 
having errors in the displayed Caller ID dig-...

0400 - Timers
0402  - Trunk Timers
DS2000 Software Manual Chapter 2: Programming385
Telephone Programming Instructions
1. Enter the programming mode.
2. 0402 + 
HOLD
3. Enter data for the displayed timer + HOLD.
OR
Press 
VO L  or VO L  to scroll to the timer you want to change + HOLD
4. Enter data for the displayed timer + HOLD
5. Press VO L  or VO L  to scroll to another timer.
OR
Press 
HOLD to return to step 2 and enter another program number.
0402:TRUNK TIMERS
CAMP ON? 

0400 - Timers
0403 - Station Timers
386Chapter 2: ProgrammingDS2000 Software Manual
0403 - Station Timers
Description
Use Program 0403- Station Timers to enter the values for station timers.
Conditions
NoneLCCPU 01.00.00 Available.
Table 24:  Program 0403 - Station Timers
OptionDescriptionEntriesDefault
Hold Recall
Use this timer to set how long a call stays on 
Hold before it recalls the extension that ini-
tially placed it on Hold.
• See Hold on page 156 for more.HOLD RECALL?0-9999 sec.60 sec....

0400 - Timers
0403 - Station Timers
DS2000 Software Manual Chapter 2: Programming387
Call Waiting Tone  IntervalUse this timer to set the interval between 
Call Waiting tones.
• See Call Waiting / Camp-On on page 51 
for more.
Also use this timer to set the interval 
between Off Hook Signaling alert tones.
• See Off-Hook Signaling on page 205 for 
more.CL WAIT  INTIRVL?0-9999 sec.10 sec.
Call Coverage DelayFor extensions with Delayed Ringing Call 
Coverage keys, this timer sets how long a 
call flashes...

0400 - Timers
0403 - Station Timers
388Chapter 2: ProgrammingDS2000 Software Manual
Telephone Programming Instructions
1. Enter the programming mode.
2. 0403 + 
HOLD
3. Enter data for the displayed timer + HOLD.
OR
Press 
VO L  or VO L  to scroll to the timer you want to change + HOLD
4. Enter data for the displayed timer + HOLD
5. Press VO L  or VO L  to scroll to another timer.
OR
Press 
HOLD to return to step 2 and enter another program number.
Ring No Answer HuntUse this timer to set the...

0400 - Timers
0404 - Analog Station Timers
DS2000 Software Manual Chapter 2: Programming389
0404 - Analog Station Timers
Description
Use 0404: Analog  Station Timers to set parameters and timers for ASTU PCBs.
Conditions
NoneLCCPU 01.00.00 Available.
OptionDescriptionEntriesDefault
Country Data
Use this option to define the country of use 
and the codec digitizing method for ASTU 
PCBs. This timer consists of two bits (xy), 
with bit x defining the country and bit y 
defining the digitization method. For...

0400 - Timers
0404 - Analog Station Timers
390Chapter 2: ProgrammingDS2000 Software Manual
Minimum Make TimeThis timer defines the minimum amount of 
time the loop must be closed to properly 
decode the dial pulse digits sent from analog 
devices connected to ASTU PCBs. Change 
this value only if the connected analog 
devices are set to dial at a rate other than 
10 PPS.MIN MAKE TIME?1-255
(5-1275 mS in 5 mS 
increments [e.g., 2 = 
10mS, 3 = 15 mS, 4 = 20 
mS)2 (10 mS)
Maximum Make TimeThis timer defines...

0400 - Timers
0404 - Analog Station Timers
DS2000 Software Manual Chapter 2: Programming391
Telephone Programming Instructions
1. Enter the programming mode.
2. 0404 + 
HOLD
3. Enter data for the displayed timer + HOLD.
OR
Press 
VO L  or VO L  to scroll to the timer you want to change + HOLD
4. Enter data for the displayed timer + HOLD
5. Press VO L  or VO L  to scroll to another timer.
OR
Press 
HOLD to return to step 2 and enter another program number.
Dial Pulse Guard TimerThe ASTU PCB waits...

0500 - System Numbering
0501 - Numbering Plan
392Chapter 2: ProgrammingDS2000 Software Manual
0500 - System Numbering
0501 - Numbering Plan
Description
Use Program 0501- Numbering Plan to customize the system’s number plan. For each dialed 
digit (0-9, excluding # and *), assign a Function Type and an Expected Digits entry. Function Type 
defines the digit’s function in the system (see the table below).
Expected Digits sets how many digits the system expects to receive when the digit string begins 
with...