Nitsuko Digital System Administrators Guide

FOR FEATURE INFORMATION:   See Direct Inward Lines on page 64.
Class of Service
Use this option to set Class of Service for outside lines (normally COS 01). If you
want an outside line to have Distinctive Ringing, assign it COS 20.
FOR FEATURE INFORMATION:   See Ringing Patterns (Distinctive Ringing) on 
page 156. 
Do not assign Distinctive Ringing if
any extensions have headsets.
Filling Out the Program Record Form
1.Select a Line (01-16). 
In this box . . .Enter this data . . .
CPG (Call Pickup Group)...

Entering Data Into Memory
To enter Program 12 data:1.Enter program mode. 
-Press # + dial SP + dial 5312 + press #. 
2.Press key 12 to enter Program 12. 
3.Dial Line No., press #. 
4.Dial abbreviation for desired feature, press #. 
5.To accept the displayed data:  Press #. 
OR 
To change or enter data:  Dial data, press #. 
-To accept DTD or DTN data, you may have to press
SAVE instead. 
-To erase a data entry before you press #: Dial *. 
6.Repeat steps 4-5 for all features. 
7.Press SAVE. 
8.Select an...

Program 4To set the Rings Before Recall timer (how long the DIL
rings before diverting)
To set the Camp-On timer for DILs to UCD Hunt Groups
Program 10To assign a name to a DIL
Program 16To give an extension (other than the terminated extension)
access to the DIL so they can answer it if it diverts to their
extension
Program 18 (II)To assign ringing to the DIL at extensions other than the
terminated extension 
Line Options Program 12: Line Features
Part II:  DIGITAL SYSTEM Programs 237 

– For your notes –
Program 12: Line Features Line Options
238 DIGITAL SYSTEM Administrator’s Guide 

Progra mming Ex te nsion Options
P rogram 14: Exte nsion Port Cha r.
&
Program 14 is initially set as follows for each station (extension)
port: 
·Extension Numbering Plan for Ports 00-47 = extensions 300-347,
respectively 
·Extension Circuit Type = X (not installed)
·DSS Owner Extension = 300 
·DSS Block Number = 01 
·Extension Name = Unassigned 
Program 14 lets you define the following characteristics for each extension port
(00-47):
Extension Numbering Plan for Ports 00-47 
Use this option to assign...

DeviceCircuit TypeLoad FactorNo. of Ports
XAUX Module - 0 Exp CEU #1
(w/3 CEUs)
Data Module
(see text below)Z/01
(no auto-ID)11
You can also install a Data Module (P/N 88400).  Before you install the Data
Module, you should do the required programming (see below).  If you install the
Data Module (with or without an extension) before you do the programming, you
must unplug the Data Module and extension (if any), then plug them back in. 
To program a stand-alone Data Module: 
Use Program 14 to assign...

FOR FEATURE INFORMATION:   See 
The Type of Phone You Have on page 6, Analog
Station Interface on page 31 and Data on page
61.
DSS Owner Extension (For DSS Consoles Only) 
Use this option to identify the extension that is paired with a DSS Console.
FOR FEATURE INFORMATION:   See Direct Station Selection, DSS Console on page 66.
DSS Block Number (For DSS Console Only) 
Use this option to assign a memory block (01-04) to a Console for its key
configuration.
FOR FEATURE INFORMATION:   See Direct Station...

Example 
Port 03 is set up as follows:  It has extension number 307, an Electronic Single Line
Phone connected to it, and the name MR. SMITH.
Entering Data Into Memory
To enter Program 14 data:1.Enter program mode. 
-Press # + dial SP + dial 5312 + press #. 
2.Press key 14 to enter Program 14. 
3.Dial Port No., press #. 
4.To accept the displayed data:  Press #. 
OR 
To change or enter data:  Dial data, press #. 
-To erase a data entry before you press #:  Dial *.
-To enter a circuit type of X:  Press...

-After exiting, you can select another program.
Understanding Related Programming
For a Data Module installed with an extension: 
Program 18 (I)To program the extension as a Dataset
Extension Options Program 14: Extension Port Char.
Part II:  DIGITAL SYSTEM Programs 243 

P rogram 15: Ac ce ss Le vel
&
Program 15 is initially set as follows: 
·Extension 300 has access level 05.
·Extensions 301-305 have access level 04.
·Extensions 306-347 have access level 01. 
Program 15 lets you assign a programming access level (00-04) to extensions
(301-347).  Extension 300 permanently has access level 05, and you cannot assign
level 05 to any other extension.  The access level determines:
·Whether you can use the extension to do system programming.  You can always
do system...