Nitsuko Digital System Administrators Guide

4.To program the keys at extension XXX:  Dial extension
XXX again, press #. 
OR 
To copy keys from extension YYY onto XXX:  Dial
YYY, press #, then go to step 8 if you do not need to
change certain keys after you copy; otherwise, go to
step 5.
-If you are programming assignments for your DSS
Console, enter your extension number. 
-This procedure does not copy: 
  Speed Dial (stored) numbers.
  Ring Assign. (Program 18 [II])
  Line Access (Program 16) 
5.Press key you wish to program. 
-For DSS Consoles,...

P rogram 18: Exte nsion Fe atures (I)
&
Program 18 is initially set as follows for each extension: 
·Do Not Disturb = Y 
·Class of Service =
- 30 for ext. 300
- 01 for ext. 301-347 
·Ring Group Member = 00 (not a member)
·Call Pickup Group Member= 00 (not a member)
·Privacy Release Group Member = 00 (not a member) 
·Off-Hook Ringing = N 
·Busy Lamp Field (BLF) and Direct Station Selection (DSS) for Keys 1-15
on a Multibutton Phone = Y 
·Line Dial-Up = Y 
·Page Zone Member = 00 (receives only All Call...

Privacy Release Group Member (PRG)
Use this option to assign a Multibutton extension to a Privacy Release Group (01-99).
FOR FEATURE INFORMATION:   See Privacy Release on page 149. 
Off-Hook Ringing (OHR) 
Use this option to enable/disable Off-Hook Ringing at an extension.  Enabling
Off-Hook Ringing for an extension also converts its Call Waiting beeps into
Off-Hook Ringing.  
Always assign Off-Hook Ring to an attendant.  Analog Station Interfaces do not
receive Off-Hook Ringing even if you enable it...

# System SpeedNumbersBlocks Used for SystemSpeed DialBlocks Available forPersonal Speed Dial
10 1/2 of 01 (1/2 of 01)-28
100 01-05 06-28
Three more things you need to know about assigning blocks are these: 
·A DSS uses four consecutive blocks. So if you assign block 05, for example, the
DSS Console actually uses 05, 06, 07, and 08. 
·You can assign the same block to more than one extension when, for example,
there are more extensions than blocks.  The extension users would share access
to the 20 bins in...

In this box . . .Enter this data . . .
DND (Do Not Disturb) Y - enable
N - disable
COS (Class of Service) 00-30
RG (Ring Group) 00-08
Note:
  00 = Not a member
CPG (Call Pickup Group) 00-07
Note:
  00 = Not a member
PRG (Privacy Release Group) 00-99
Note:
  00 = Not a member
OHR (Off-Hook Ring) Y - enable
N - disable
BLF (DSS/BLF Lamps) Y - enable
N - disable
LDU (Line Dial-Up) Y - enable
N - disable
PZ (Page Zone) 00 - Receives All Call only
01-07 - Receives All Call and
pages to Zones 01-07
SO (Station...

 Filling Out the Program Record Form
Example 
Extension 305 has Do Not Disturb disabled (no other options will be shown).
Entering Data Into Memory
To enter Program 18 (Part
I) data:
1.Enter program mode. 
-Press # + dial SP + dial 5312 + press #. 
2.Press key 18 (CONF key) to enter Program 18. 
3.Dial extension number, press #. 
4.Dial abbreviation for desired feature, press #.
-To dial PZ:  Dial P, then 0 (zero). 
5.To accept the displayed data:  Press #. 
OR 
To change or enter data:  Dial data, press...

Understanding Related Programming
For Class of Service:
Program 1To set up a Class of Service
For Privacy Release Groups:
Program 16To give an extension outgoing access to the lines intended
for Privacy Release
Program 17To assign a Privacy Release line to a key at an extension 
For DSS/BLF:
Program 18 (II)To determine which extensions the DSS keys call
For Line Dial-Up:
Program 16To give an extension outgoing access to lines
For Page Zones:
Program 18 (II)To enable/disable incoming pages at an...

For Door Box:
Program 18(I)Each Digital Door Box extension must have Class of
Service 28.
Program 18: Extension Features (I) Extension Options
262 DIGITAL SYSTEM Administrator’s Guide 

P rogram 18: Exte nsion Fe atures (II)
&
Program 18 is initially set as follows for each extension:
·Day/Night Ringing Assignments = Y for all lines at ext. 300; N for all
lines at all other extensions; N for all Call Coverage and Pickup keys 
·Night Ringing = N for all lines 
·Delayed Ringing Assignment = N for all lines; N for all Call Coverage
and Pickup keys
·Prime Line Assignment = N for all lines 
·Ringing Line Preference = N for all lines 
·Direct Station Selection Key Assignments = Keys 1-15 at a...

Prime Line Assignment (PLA)
Use this option to enable/disable a Prime Line key for a Multibutton phone.  When
you enable Prime Line for a Line key, the system automatically assigns Ringing Line
Preference (below) to that Line key.  Do not assign a Prime Line to an attendant or
Headset extension.
FOR FEATURE INFORMATION:   See Placing an Outside call (Using Prime Line) 
on page 134.
Ringing Line Preference (RLP)
Use this option to assign Ringing Line Preference to a Multibutton extension.  Do not
assign...