Nitsuko 124i/384i Software Manual

Programming (Cont’d)
Continued
from
previous
page.
For ringing extensions,
should extension ring
when line key starts
flashing or wait for the
system ring cycle?
In 0306, enter 1 to
enable pre-ringing for
trunk calls.In 0306, enter 0 to
disable pre-ringing for
trunk calls.When line
key flashesWait for
ring cycle
In 0405:7, set the
Ring No Answer
Alarm Time interval.
Do you want one-button
incoming access to
each trunk?In 1006, program function
keys as line keys (codes
0001-0128).
Do you want loop
keys...

Programming (Cont’d)
No
Yes
Yes NoUniversal Answer
Stop
Stop
In 1005, assign Class of
Service to extensions.
In 0406 Item 126, enter 0.In 0406 Item 126, enter 1.
Should extension be able
to dial the Universal
Answer code? Universal Answer will answer the trunk if it is in the
extensions programmed route.
In 1015, assign extensions to
the routes set up in 0906.
Using Trunk Groups
assigned in 0905, in 0906
set up a routing table.
Do you want Universal
Answer capability?
Continued
from previous
page....

Programming (Cont’d)
➣
0111 - Trunk Ring Tone
Customize the ring tones within each Ring Tone Range. Assign Ring Tone Ranges to trunks in 0902.
Trunks ring extensions according to the Ring Tone Range selected in 0902 and the user settings made
with Service Code 820.
➣0117 - Trunk CODEC Gain Type Settings
Customize the transmit and receive levels of the CODEC Gain Types assigned in 0901 Item 3.
➣(384i Only) 0129 - Analog Trunk (ATRU PCB) Sidetone Setting
Set the side level for analog trunks connected to...

Programming (Cont’d)
➣
1001 - Basic Extension Port Setup (Part A), Item 2: Trunk Ring Tone
Trunks ring extensions according to the Ring Tone Range selected in 0902 and the settings made with
either Service Code 820 or Program 1001 Item 2. Also see Program 0902.
➣1001 - Basic Extension Port Setup (Part A), Item 4: CODEC Gain Type
Adjust the gain settings for single line telephones.
➣1001 - Basic Extension Port Setup (Part A), Item 6: Incoming Ring for 
500/2500 Sets
Use this option along with Program 1008...

Operation
To answer an incoming trunk call:
1. Lift handset.
2. At keyset, press flashing line key.
If you don’t have a line or loop key for a trunk call ringing your phone, it rings an idle CALL key.
If you have Ringing Line Preference, lifting the handset answers the call.
You can dial after answering the call. This allows you, for example, to respond to computer-gen-
erated incoming calls.
To use Universal Answer to answer a call ringing over the Paging system:
1. At keyset, press idle CALL key
OR
At...

Central Office Calls, Placing
Description
 124i Available — 52 trunks. 384i Available — 128 trunks. 
- Customizing CODEC Gains and
setting up Alternate Trunk Access
Codes require Base 2.13, EXCPRU
2.18 or higher.- Customizing CODEC Gains and
setting up Alternate Trunk Access
Codes require system software 3.04
or higher.
- The ability to turn DTMF tones for
outgoing trunk calls on and off
requires Base 2.13, EXCPRU 2.18 or
higher.- The ability to turn DTMF tones for
outgoing trunk calls on and off is...

Programming
Start
Should system users be
able to place outgoing
calls on trunks?In 0406:62, enter 1 to
enable outgoing calls for
Tenant Group.In 0406:62, enter 0 to
disable outgoing calls for
Tenant Group.YesNo
StopIn 1005, assign
Class of Service to
extensions.
Are outgoing
calls allowed on
specific trunks?In 0901:18, enter 1 to
allow outgoing calls.In 0901:18, enter 0 to
prevent outgoing calls.YesNo
Do you need to restrict
certain extensions
from placing calls on
certain trunks?Build an outgoing...

Programming (Cont’d)
Continued
from
previous
page.
If a user preselects a line, how
long should the system
remember the preselection?In 0405:15, enter the
preselection interval.
Should extension users
have one-button placing
of outside calls?In 1006, assign function
keys as line keys (codes
0001-0128).In 1006, do not assign
function keys as line keys
(codes 0001-0128).
Should extension users
have one-button access
to trunk groups for
placing calls?In 1006, assign Trunk Group
Routing/dial 9 keys (code...

Programming (Cont’d)
Stop
Continued
from
previous
page.
Check the Analog Trunk
Timers in 0114 and 0135 for
compatibility with the telco.
If desired, assign names
to trunks in 0903.
Do you want to set up
an Alternate Trunk
Route Access Code
(384i only)?
StopIn 0501, set up a Service
Code for Alternate Trunk
Route Access. For example, to make
50 the Alternate Trunk
Route Access Code:
DIAL = 5
Digit = 2
Kind = 8
In 0518, assign the
Service Code set up in the
previous step for Alternate
Trunk Route Access....

Programming (Cont’d)
➣
0114 - Analog Trunk (ATRU PCB) Timers (Part A)
0135 - Analog Trunk (ATRU PCB) Timers (Part B)
Review the Analog Trunk Timers for compatibility with the connected telco.
➣0117 - Trunk CODEC Gain Type Settings
Customize the transmit and receive levels of the CODEC Gain Types assigned in 0901 Item 3. 
➣(384i Only) 0129 - Analog Trunk (ATRU PCB) Side tone Setting
Set the side tone level for analog trunks connected to ATRU PCB ports.
➣0405 - System Timers (Part A), Item 15: Preselection...