NEC Visualink 128/384 Engineering Guide
Have a look at the manual NEC Visualink 128/384 Engineering Guide online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1168 NEC manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
NDA-24233 Issue 2Page 3-55 VisuaLink 128/384 Engineering Guide Console Command List 3.20 Camera Control Command CAMS Request for Camera Direction Change 20-1 Description: Sets camera head swing control. This command is valid only when an preset or auto mode camera is in use. A control of Camera 2 is only valid when the camera is the EVI-D30 type. Command Format: CMAS p1 p2 p1: L1-2 : local camera 1/ 2 control R1-2 : remote camera 1/ 2 control p2: 1-9 : preset number Z x : zoom change F x : focus change P x : pan change T x : tilt change UP x : diagonally upper direction DP x : diagonally lower direction H : center Note: x: + : positive direction - : negative direction 0 : stop moving (changing) Response: Normal Response OK Error Response: ERR01 ERR11 ERR12 ERR16 ERR20 ERR27 T+ UP+UP- P+ P- DP- T- DP+
Page 3-56NDA-24233 Issue 2 Console Command List VisuaLink 128/384 Engineering Guide 3.21 Option Control Command POCS Pointer Control 21-1 VCTS Talker Detection Control 21-2 Description: Activates or deactivates the on-screen pointer . The pointer is displayed at the remote monitor. This pointer can only be activated when both systems (Remote/Local) are set to a NEC mode. Command Format: POCS p1 p2 p3 p1: ON/OFF : control on/off p2: 1-99 : X-axis p3: 1-99 : Y-axis Response: Normal Response: When Parameter is Omitted: p1 p2 p3 OK p1: ON/OFF : control on/off p2: 1-99 : X-axis p3: 1-99 : Y-axis When Parameter is Specified: OK Error Response: ERR01 ERR36 Description: Activates or deactivates talker detection. When audio is detected the camera will move to a selected preset (1-3). This command is valid only with preset or auto mode camera. Command Format: VCTS p1 p1: ON : speaker detection control ON p2: OFF : speaker detection control OFF Response: Normal Response: When Parameter is Omitted: p1OK p1: ON/OFF : control ON/OFF When Parameter is Specified: OK Error Response: ERR01
NDA-24233 Issue 2Page 3-57 VisuaLink 128/384 Engineering Guide Console Command List STPR SnapShot Transmission Request 21-3 SXMR Standard Display Screen Setting Request 21-4 Description: Sends a snapshot (still graphic) image to the remote site. Command Format: STRP Response: Normal Response OK Error Response: ERR01 Description: Requests for a display setting change when going through the MCU. This command is only valid when going through an NEC multi-point control unit, that has multi-screen control capability. Command Format: SXMR p1 p1: S : single screen M : multiple composite screen Response: Normal Response: When Parameter is Omitted: p1 OK p1: S : single screen M : multiple composite screen When Parameter is Specified: OK Error Response: ERR01
Page 3-58NDA-24233 Issue 2 Console Command List VisuaLink 128/384 Engineering Guide SXST Request to Acquire Composite Screen Setting 21-5 Description: Request for status on the various video screens displays. This command is only valid when going through an NEC multi-point control unit MCU5000A, that has multi-screen control capability. Command Format: SXST p1 p2 p3 p1: Composite Screen Status D7-D5 : 0 fixed D4-D3 : re-lineup 00: none 10: in the order of terminal number D2 : speaker display 0: none 1: yes D1-D0 : 0 fixed p2 : Number of Composite Screen : 04: 4 screens 09: 9 screens 16: 16 screens p3 : Composite Pattern : A fixed Response: Normal Response: When Parameter is specified: OK When Parameter is omitted: p1 p2/p3 p4=p5; p6 OK p1: Composite Screen Status D7-D5 : 0 fixed D4-D3 : re-lineup 00: none 10: in the order of terminal number D2 : speaker display 0: none 1: yes D1-D0 : 0 fixed p2 : Number of Composite Screen : 04: 4 screens 09: 9 screens 16: 16 screens p3 : Composite Pattern : A fixed p4 : Composite Screen Position :01~16 p5 : MCU number : 00-FF p6 : Terminal number : 00-FF Example: SXST 00 04/A 01=01:01 02=01:02 03=01:03 OK Error Response: ERR01 D7 D6D5 D4D3 D2D1 D0 D7 D6D5 D4D3 D2D1 D0
NDA-24233 Issue 2Page 3-59 VisuaLink 128/384 Engineering Guide Console Command List 3.22 Multi-point Conference Control COPR Request to Chairman Control 22-1 Description: Acquires or deletes chairman control. Command is only valid when the VisuaLink is in a multi-point conference. Command Format: COPR p1 p2 p1: 1-14 : conference room number (specified only in a NEC specific multi-point conference) p2: ON : acquire OFF : release Note 1: When p1 is omitted, it becomes a local office conference room number. Note 2: p1 is omitted in H.243 multi-point conference. Response: Normal Response OK Error Response: ERR01 ERR20 ERR22 ERR23 ERR24 ERR26
Page 3-60NDA-24233 Issue 2 Console Command List VisuaLink 128/384 Engineering Guide CSPR Multiple Address Transmission Request 22-2 Description: Acquires the simulcast transmission. Command Format: CSPR p1 p1: 0-255 : conference room number to be received * : composite screen display Note 1: When p1 is omitted, it becomes a local office conference room number. Also in a NEC specific multi-point conference, 1-14 only can be specified. Note 2: In p1, * is valid only when a MCU to connect has a capability of screen composition. Note 3: In p1, “0” is valid in H.243 multi-point conference. It means a release of simulcast transmission. Response: Normal Response OK Error Response: ERR01 ERR20 ERR22 ERR23 ERR24 ERR26
NDA-24233 Issue 2Page 3-61 VisuaLink 128/384 Engineering Guide Console Command List CRPR Specific Picture Reception Request 22-3 CMPR Request to Switch Multiple Address Originator Monitor 22-4 Description: Activates or deactivates selective receive mode. Command Format: CRPR p1 p2 p3 p1: 1-255 : reception side conference room number p2: 1-255 : transmission side conference room number * : composite screen display p3: ON : reception selection setting/ release OFF : reception selection release Note 1: When p1 is omitted, it becomes a local office conference room number. Note 2: p1 is omitted in H.243 multi-point conference. Note 3: In p2, * is valid only when a MCU to connect has a capability of screen composition. Also in a NEC specific multi-point conference, 1-14 only can be specified. Response: Normal Response OK Error Response: ERR01 ERR20 ERR22 ERR23 ERR24 ERR26 Description: Request to switch the broadcasting video image at the originator’s monitor. This command is only available when it is in a NEC specific conference mode. Command Format: CMPR p1 p1: 1-14 : conference room number Response: Normal Response OK Error Response: ERR01 ERR20 ERR22 ERR23 ERR24 ERR26
Page 3-62NDA-24233 Issue 2 Console Command List VisuaLink 128/384 Engineering Guide 3.23 Opening Control Command OMES Opening Message at Unit Activation 23-1 Description: Report opening message at power up. This is reported when the unit is automatically re-start due to some failure. In the case of automatic reset, please perform necessary procedures to reconnect the line. Command Format: OMES p1 p2 p1: TC2000-EC : VL128 TC2000-6B : VL384 p2: F/W version (ex) V01.00.00
NDA-24233 Issue 2Page 3-63 VisuaLink 128/384 Engineering Guide Console Command List 3.24 Communication Status Report Command H221 H.221 Synchronous Status Report 24-1 IMAC Manufacturer Code Report 24-2 Description: H.221 reporting status change. Command Format: H221 p1 p1: AI : synchronization established DI : out of synchronization Description: Reports a manufacturer code for the remote site. Command Format: IMAC p1 p2 p3 p4 p5 OK p1: 00-FF : Manufacturer code 49 : NEC Else : other vendor p2: 00-FF : Division code 00 : NEC Else : other division of NEC p3: 00-FF : Unit code 00 : TC5000EX7 01 : TC5000EX10 02 : MMVC 03 : VL128/384 10 : MCU5000A Else : Reserved p4: 00-FF : Own Capability code D0: Kanji Display Capability 0: Off 1: On D1: Composite Screen Display Capability 0: Off 1: On D2: H281 Camera Control Capability 0: Off 1: On p5: 00-FF : Reserved D7 D6D5 D4D3 D2D1 D0
Page 3-64NDA-24233 Issue 2 Console Command List VisuaLink 128/384 Engineering Guide IMOD Report of Common Mode in Communication 24-3 Description: Reports the negotiated mode during a communication. Command Format: RMOD p1 p2 p3 p4 p5 p6 p7 p8 p1: B/2B/3B/4B/5B/6B : communication speed p2: 56/64 : network TYPE p3: QCIF/FCIF : video format p4: ULW/ SBA/ LDC/ OFF : audio mode p5: 4.0/6.4/14.4/24.0/VMLP/OFF : MLP speed p6: ON/OFF : MBE capability p7: ON/OFF : T120 capability P8: 1.2/4.8/9.6/14.4/OFF : LSD SPEED