NEC Visualink 128/384 Director Guide

							NDA-24248 Revision 1.0Page 11-5
VisuaLink 128/384 Director Guide Chapter 11
11.1.3  Data Setting
Use this function to set the data communication speed. 
Select Maintenance
 | Environment
 to display Environment
 dialog, then Data 
tab.
Figure 11-5:   Data Setting
A. MLP Speed
You can set the MLP speed that is used for the data conference, NEC proprietary 
conference, and NEC proprietary camera control. Default value is 4.0 kbps.
B. LSD Speed
You can set the LSD speed that is used for the data transfer, and ITU-T standard 
camera control. Default value is 1.2 kbps.
A
B 
						

							Page 11-6NDA-24248 Revision 1.0
Chapter 11 VisuaLink 128/384 Director Guide
11.1.4  User 1 Setting
Use this function to set the user information and call receiving. 
Select Maintenance
 | Environment
 to display Environment
 dialog, then User 1 
tab.
Figure 11-6:   User 1 Setting
A. Phone Number
You can enter your own phone number (dial/sub address). Only numerical texts 
are available for the phone number entry. Maximum characters are 20 for the 
phone number and 8 for the sub address. No registered data appears for the 
default.
B. Location
You can enter own location. Data entry is not available when you activate Delete 
Own Information
. No registered data appears for the default.
C. Delete Own Information
Check this checkbox when you wish to delete your registered phone number and 
location.
D. Reception
 Mode
Use this section to specify the call receiving mode. Default value is Auto.
E. Call Notification
Check this checkbox to activate a buzzer when you receive a call. Default is 
unchecked.
F.   Number of Rings
Set the number of rings that are required before call is answered.
A
BC
D
E
F 
						

							NDA-24248 Revision 1.0Page 11-7
VisuaLink 128/384 Director Guide Chapter 11
Note:
You cannot set Phone Number
, Receiving Mode
, and Call Notification
 
when the basic proprietary line.
11.1.5  User 2 Setting
Use this function to set the start-up information setting for VisuaLink Director.
Select Maintenance
 | Environment
 to display Environment
 dialog, then User 2 
tab.
Figure 11-7:   User 2 Setting
A. Display Password
 dialog
Check this checkbox to display Confirm Password
 dialog for each VisuaLink 
Director start-up operation. Default is unchecked (hide Confirm Password
 
dialog).
B. Display Run
 dialog
Check this checkbox to display Run
 dialog for each VisuaLink Director start-up 
operation. Default is checked (display Run
 dialog).
C. Video Capture Application
Check this checkbox to start the video capture application from a default path. 
Default is unchecked (deactivate video capture application).
D. Video Capture Application Path
To change a path, you can manually type a path of the video capture application. 
E. Data Conference Application
Check this checkbox to start the data conference application from a default path. 
Default is unchecked (deactivate data conference application).
F.  Data Conference Application Path
To change a path, you can manually type a path of the data conference application.
A
B
C
D
E
FG
H 
						

							Page 11-8NDA-24248 Revision 1.0
Chapter 11 VisuaLink 128/384 Director Guide
G. [Reference…]
 button
To change a path, you can also click this button to display Select Path
 dialog that 
allows you to select a path visually.
H. PC COM Port for VisuaLink
 buttons
Select the correct COM port that is connected to the VisuaLink.
11.1.6  Line Setting
Use this function to set the start-up information setting for VisuaLink Director.
Select Maintenance
 | Environment
 to display Environment
 dialog, then Line 
tab.
Figure 11-8:   Line Setting
A. Network
Use this field to select a network type for the conference capability of call 
receiving. Default is Px64.
B. Communication Speed
Use this field to select a communication speed for the conference capability of call 
receiving. Default is 2B.
C. Line Type
Use this field to select a line type for the conference capability of call receiving. 
Default is National ISDN (NI1).
A
B
C 
						

							NDA-24248 Revision 1.0Page 11-9
VisuaLink 128/384 Director Guide Chapter 11
11.1.7  Serial Setting
Use this function to set the Serial Port 1.
Select Maintenance
 | Environment
 to display Environment
 dialog, then Serial 
tab.
Figure 11-9:   Serial Setting
A. Serial Port 1
Use this field to select a hardware that you wish to connect to VisuaLink. Default 
is Camera (EVI-D30).
B. Camera Control
Use this field to select a remote camera control method. To activate this item, you 
need to select Camera (EVI-D30) or Camera (VC-C1) on Serial Port 1
 field. 
Default is Auto.
AB 
						

							Page 11-10NDA-24248 Revision 1.0
Chapter 11 VisuaLink 128/384 Director Guide
11.2 Changing Your 
PasswordFollow the operation below to change the registered password.
Operation
Select Maintenance
 | Change Password 
from the Main Menu
.
Figure 11-10:   Change Password Menu
Change Password
 dialog appears.
Figure 11-11:   Change Password
A. Current Password
Type the currently registered password. “*” will appear as you type. 
B. New Password
Type new password that you wish to register. You can enter up to 16 characters. 
“*” will appear as you type. Spacing is not available.
C. Cancel
 button
Click this button to close Change Password
 dialog and quit this function.
Type both Current Password
 and New Password
, then click OK
. Password 
Confirmation
 dialog appears when current password and registered password 
match. If you enter an incorrect password, you are prompted to reenter the 
password correctly.
Type the new password that you registered, then click OK
. When the new and 
registered password are matched, system updates the password and closes both 
A
B
C 
						

							NDA-24248 Revision 1.0Page 11-11
VisuaLink 128/384 Director Guide Chapter 11
Password Confirmation
 dialog and Change Password
. 
If entered password is incorrect, you need to reenter the correct password. 
Click Cancel
 to close Password Confirmation
 dialog, then quit this function. 
						

							Page 11-12NDA-24248 Revision 1.0
Chapter 11 VisuaLink 128/384 Director Guide
11.3 Starting a 
Loopback TestYou can test the system operation by executing the remote/local loopback test.
Follow the operation below to start the loopback test.
Operation
Select Maintenance
 | Loopback Test 
from the Main Menu
.
Figure 11-12:   Maintenance Menu
Loopback Test
 dialog appears. 
Select a test method that you wish to manipulate.
Figure 11-13:   Loopback Test
A. Local Loopback Test
You can select the test items. You cannot start this test when the conference is in 
process.
B. Remote Loopback Test
You can start the Remote Loopback Test. You cannot start this test when the 
conference is not in process.
C. Test Window
Displays the progress of the loopback test being performed.
D.  Release 
button
Press the Release button to cancel the loopback test.
A
CD
EB 
						

							NDA-24248 Revision 1.0Page 11-13
VisuaLink 128/384 Director Guide Chapter 11
E.  Finish
 button
Click Finish
. If you click this button during the testing, the system aborts the test 
and closes Loopback Test
 dialog. 
						

							Page 11-14NDA-24248 Revision 1.0
Chapter 11 VisuaLink 128/384 Director Guide
11.4 Viewing a 
Communication 
HistoryYou can confirm the previous communication history. 
Follow the operation below to view the history.
Operation
Select Maintenance
 | Communication History View 
from the Main menu
.
Figure 11-14:   Maintenance Menu