NEC Neax2000 Ivs Small Platform System Manual

ND-46551 (E) CHAPTER 3
Page 49
Revision 2.0
NAP-200-003
Sheet 19/21
Installation of Main Equipment
(2) Connect the RACK PARTS to each other.
Note :This installation procedure is required when the system is 3 modules (PIM + MDFM + BATTM).
Figure 003-17  Connection of RACK PARTS
RACK PARTS
REAR
RACK PARTS
BASE 

CHAPTER 3 ND-46551 (E)
Pag e 5 0
Revision 2.0
NAP-200-003
Sheet 20/21
Installation of Main Equipment
(3) Connect the PIM to the RACK PARTS using the 4 screws provided with the RACK PARTS.
Note :This installation procedure is required when the system is 3 modules (PIM + MDFM + BATTM).
Figure 003-18  Connection of the PIM and the RACK PARTS
REAR
PIM  Note
BASE
Note :The BATTM and the MDFM can be installed in the same manner as the PIM. 

ND -4 6551 ( E)  CHAPTER 3
NAP-200-0 03
MD FMN ote 

CHAPTER 3 ND-46551 (E)
Pag e 5 2
Revision 2.0
NAP-200-004
Sheet 1/5
Connection of Battery
1. BATTERY CONNECTION
CAUTION 1:24V batteries must be used in this system.
CAUTION 2:If battery terminals (+, –) contact with the module under connecting the battery cable to the PZ-
PW86 card, the PZ-PW86 card or the BWB may be broken. Therefore, the installer must per-
form work in accordance with the following steps when mounting or removing the batteries.
• When mounting batteries:
(1) Connect the battery cable...

ND-46551 (E) CHAPTER 3
Page 53
Revision 2.0
NAP-200-004
Sheet 2/5
Connection of Battery
CAUTION 3:Battery Replacement Table and Battery Warnings
The label, which shows battery replacement table and battery warnings, is attached to the re-
verse side of Front Cover for PIM and BATTM.
During the battery installation process, always observe the warning statements. When replacing
batteries, adhere to the battery replacement table to increase battery life and to insure safe op-
eration.
25° C ~ 30° C
2.0 ~...

CHAPTER 3 ND-46551 (E)
Pag e 5 4
Revision 2.0
NAP-200-004
Sheet 3/5
Connection of Battery
1.1 Internal Battery Connection
(1) Mount the battery unit (24 V DC, 3.4 AH) into the PIM.
Figure 004-1  Internal Battery Mounting
FRONT 67mmDIMENSION OF BATTERY
BATTERY UNIT
(24V DC, 3.4AH)
(LOCALLY PROVIDED)
(2.6 inch)
134mm
(5.3 inch) 60mm
(2.4 inch)
PIM
BASE 

ND -4 6551 ( E)  CHAPTER 3
NAP-200-0 04
P LUG IN  TO B ATT  1
BASE 

CHAPTER 3  ND -4 6551 ( E)
NAP-2 00-0 04
T O PZ -PW 86 IN P IM 

ND -4 6551 ( E)  CHAPTER 3
NAP-200-005
T O PIM
TWI STE D 25  PA IR CAB LES
TO  MDF 

CHAPTER 3 ND-46551 (E)
Pag e 5 8
Revision 2.0
NAP-200-005
Sheet 2/5
Cable Running to the MDF
2. INSTALLATION OF EXTERNAL MDF
• Secure the external MDF onto the floor or mount the MDF onto the wall.
• Mount the required MDF components.
• If required, install the cable ducts for the cables to be laid between the MDF and the Main Equipment. In
this case, confirm the locations of the cable holes for the Main Equipment. See Figure 005-2.
Figure 005-2  Cable Hole Location
FRONT
430 mm (16.9 inch)
RACK PARTS...