NEC Neax2000 Ivs Small Platform System Manual

ND-46551 (E) REGULATORY INFORMATION
Page ix
Revision 2.0
(b) This equipment returns answer supervision on all DID calls forwarded to the PSTN. Permissible ex-
ceptions are:
• A call is unanswered
• A busy tone is received
• A reorder tone is received.
EQUAL ACCESS REQUIREMENTS
This equipment is capable of providing users access to interstate providers of operator services through the use of
access codes. Modification of this equipment by call aggregators to block access dialing codes is a violation of...

REGULATORY INFORMATION ND-46551 (E)
Pag e x
Revision 2.0
Repairs to certified equipment should be made by an authorized Canadian maintenance facility designated by the
supplier. Any repairs or installations made by the user to this equipment, or equipment malfunctions, may give the
telecommunications company cause to request that the user disconnect the equipment.
Users should ensure for their own protection that the electrical ground connections of the power utility, telephone
lines, and internal...

ND-46551 (E) REGULATORY INFORMATION
Page xi
Revision 2.0
(10) Slots and openings in the cabinet and the back or bottom are provided for ventilation, to protect it from
overheating, these openings must not be blocked or covered. The openings should never be blocked by plac-
ing the product on a bed, sofa, rug, or other similar surface. This product should never be placed near or
over a radiator or heat register. This product should not be placed in a built-in installation unless proper
ventilation is...

ND-46551 (E) CHAPTER 1
Page 1
Revision 2.0
CHAPTER 1 INTRODUCTION
1. PURPOSE
This manual explains the installation procedure for the NEAX2000 IVS (PBX) Small Platform System.
2. REFERENCE MANUAL
During installation, refer also to the NEAX2000 IVS manuals below:
Figure 1-1   Reference Manuals for Installation
CIRCUIT CARD MANUALCOMMAND DESCRIPTION MAINTENANCE PROCEDURE
MAINTENANCE MANUAL REFERENCE MANUALS
COMMAND MANUAL
CIRCUIT CARD DESCRIPTION
CIRCUIT CARD MOUNTING CONDITIONS
SWITCH SETTING OF CIRCUIT...

CHAPTER 1 ND-46551 (E)
Pag e 2
Revision 2.0
3. HOW TO FOLLOW THIS MANUAL
The Installation Procedure is shown by means of flowcharts with an NAP (NEC Action Procedure) Number.  The
detail of the work for each step is described in corresponding NAP.
4. SCOPE OF INSTALLATION PROCEDURES
This manual covers the installation shown in Figure 1-2.
Figure 1-2   Scope of Installation Procedures
MDF
MDF CABLESN610
ATTCON
Multiline Terminal
NAP-200-003:
INSTALLATION OF MAIN EQUIPMENT
NAP-200-007:
SWITCH SETTING OF...

ND-46551 (E) CHAPTER 2
Page 3
Revision 2.0
CHAPTER 2 GENERAL INFORMATION
1. TRUNKING DIAGRAM
Figure 2-1 shows a typical trunking diagram for the PBX.
Figure 2-1   PBX Trunking Diagram
MODEM
Note 1:An external Modem is not required when the Built-In Modem on the MP is used.
Note 2:The equipment marked with (*) is provided by the customer.
4W E&M
2W E&M
RS 232C
V. 1 1
TCP/IP
V. 1 1
RS-232C
RS 232C
LONG LINE STATION
SINGLE LINE
TELEPHONE
VOICE MAI L
SYSTEM
Multiline Terminal
DSS
Multiline TerminalLONG LINE...

CHAPTER 2  ND -4 6551 ( E)
N ote :  Refe r to  NAP -200-0 08  a nd  th e C ir c ui t C ard M anua l for d eta il s  of c ir c ui t c a rd s. 

ND-46551 (E) CHAPTER 2
Page 5
Revision 2.0
2. SYSTEM CONFIGURATIONS
The PBX system provides four installation methods as follows:
• Floor Standing Installation
• Wall-Mounting Installation
• 19-Inch Rack-Mounting Installation
• Desk Top Installation
This equipment can only be serviced by a qualified service person.
Examples of system configurations for each installation method are shown in Figure 2-2 through Figure 2-5.
Figure 2-2   Floor Standing Installation
BASE PIM
FRONT 

CHAPTER 2 ND-46551 (E)
Pag e 6
Revision 2.0
Figure 2-3   Wall-Mounting Installation
PIM
RACK PARTS 

ND-46551 (E) CHAPTER 2
Page 7
Revision 2.0
Figure 2-4   19-Inch Rack-Mounting Installation
PIM
19”BRACKET (F)
 


 


•
•
•
•