NEC Neax2000 Ivs Small Platform System Manual

ND-46551 (E) CHAPTER 3
Page 39
Revision 2.0
NAP-200-003
Sheet 9/21
Installation of Main Equipment
3. 19-INCH RACK-MOUNTING INSTALLATION
(1) Before mounting the PIM, connect the TOP COVER, BOTTOM COVER and AC CORD-A-U to the PIM.
The AC CORD-A-U is pre-installed with the BOTTOM COVER.
Figure 003-8  Connecting the Covers and AC CORD to the PIM
TOP COVER
TO PZ-PW86 PIM
AC CORD-A-U
BOTTOM COVER
LOCAL CABLE DUCT 

CHAPTER 3  ND -4 6551 ( E)
NAP-2 00-0 03
B
C
A
\
 
\
\
B
C
FR ONT
PIM 

ND-46551 (E) CHAPTER 3
Page 41
Revision 2.0
NAP-200-003
Sheet 11/21
Installation of Main Equipment
4. DESK TOP INSTALLATION
(1) Connect the TOP COVER, BOTTOM COVER and AC CORD-A-U to the PIM. The AC CORD-A-U is
pre-installed with the BOTTOM COVER.
Figure 003-10  Connecting the Covers and AC CORD to the PIM
TOP COVER
TO PZ-PW86 PIM
AC CORD-A-U
BOTTOM COVER
LOCAL CABLE DUCT 

CHAPTER 3 ND-46551 (E)
Pag e 4 2
Revision 2.0
NAP-200-003
Sheet 12/21
Installation of Main Equipment
(2) Connect the RUBBER FOOT to the PIM.
Figure 003-11  Connecting the RUBBER FOOT to the PIM
 

PUSHPIN
RUBBER FOOT BOTTOMPIM 

ND-46551 (E) CHAPTER 3
Page 43
Revision 2.0
NAP-200-003
Sheet 13/21
Installation of Main Equipment
5. AC POWER CABLING
(1) The cable connections on the PZ-PW86 card are shown below.
Figure 003-12  Cable Connection on the PZ-PW86
PZ-PW86
MJ
MN
ON BATTERY MODE SWITCH
GND  
Note 2
FG
-27V
PWR CNT CA-A
PWR CA-A
BATTERY CABLE/PWR CA-A TO PWR 1
TO OT HER
AC C ORD -A
TO AC MAINS INPUT TO  POWER OUTPUT
POWER OUTPUT
TO PWR0A CONNECTOR
TO PWR0B CONNECTOR CABLE (+5V, -27V,E)
CABLE (CR, E)
CONNECTOR
PZ-PW86 TO...

CHAPTER 3  ND -4 6551 ( E)
NAP-2 00-0 03
PZ- PW 86(D)
PW R CNT C A-A
AC CORD-B
TO  THE  TER MINAL  B LOCK  AT  BASE
N ote 1 :Follo w th e La bel  on F ro n t  P lat e o f  P Z-
1
TE R M INAL  O N THE  
TO P WR0D  CONNEC TOR
P O WER  OUTPUT CAB LE  (+ 90 V,E)
T O  B ATTE R Y O R
BAT TE RY CAB LE/ PWR  CA-A
CHAS SIS  (F O R  1-PIM  S Y STE MS)
L
•
 P Z-P W86 (D)
CAU TION :Set the  ap p ro p ria te  volt- 

ND-46551 (E) CHAPTER 3
Page 45
Revision 2.0
NAP-200-003
Sheet 15/21
Installation of Main Equipment
(2) Confirm the connection of the PWR CNT CA-A and power output cables (These cables are pre-installed).
Figure 003-13  Cable Connection between the PZ-PW86 and the BWB
LTC CONNECTOR AREA
PIM
BWB (Back Wiring Board)PZ-PW86
PWR0BPWR0APWR1
POWER OUTPUTPOWER OUTPUT CARD SLOT AREA
PWR0C
PWR0D
PWR CNT CA-A
CABLE (+5V, -27V, E)
CABLE (CR, E)
POWER OUTPUT
CABLE (+80 V, E) FOR MESSAGE WAITING 

CHAPTER 3  ND -4 6551 ( E)
NAP-2 00-0 03
TO  
     
GROUND  TERMINAL
FR ONT
3P  AC PO WER CA BLE
PIM
AC CORD-B 

ND-46551 (E) CHAPTER 3
Page 47
Revision 2.0
NAP-200-003
Sheet 17/21
Installation of Main Equipment
(b) Secure the AC CORD-B cables to the FG, NEUTRAL and LINE terminals. The 3P AC Power Cable
and the FG Cable are pre-installed with the BASE.
Figure 003-15  Screwing the AC CORD-B to the Terminals
FG
NEUTRAL
LINE
BASE
3P AC POWER CABLE
TO 120/240 V AC  
SOURCE POWER
AC POWER 
KNOCK OUT HOLE
(PROVIDED WITH BASE)
FG CABLE
(PROVIDED WITH BASE)
PIMAC CORD-B 
PUSH 
PULL:  INSERT THE AC CORD 
:  FIXED THE AC...

CHAPTER 3 ND-46551 (E)
Pag e 4 8
Revision 2.0
NAP-200-003
Sheet 18/21
Installation of Main Equipment
6. MDFM/BATTM INSTALLATION
When installing the MDFM and BATTM, follow the installation below.
(1) Connect the RACK PARTS to the rear side of the BASE using the M5 Machine screws (provided).
Note :This installation procedure is required when the system is 3 modules (PIM + MDFM + BATTM).
Figure 003-16  Connection of RACK PARTS and BASE
RACK PARTS
BASE
REAR
M5 MACHINE SCREW-C 
(X2/JOINT AREA) 
(PROVIDED WITH...