NEC Neax2000 Ivs Small Platform System Manual

ND-46551 (E) CHAPTER 3
Page 19
Revision 2.0
CHAPTER 3 INSTALLATION PROCEDURE
1. PRECAUTIONS
1.1 Grounding Requirements
The system grounding must have a specific ground resistance and AC noise level, and is to be connected to a pre-
determined terminal in the PBX. Standard grounding requirements are as follows:
• Communication grounding: Less than 10 ohm
• Protective ground for PIM: Less than 10 ohm
Note :The AC ripple on these various grounds should be less than 0.5 Vp-p.
CAUTION:
Grounding circuit...

CHAPTER 3 ND-46551 (E)
Pag e 2 0
Revision 2.0
1.2 Static Electricity Guard
The installer must wear a grounded wrist strap to protect circuit cards from static electricity.
Figure 3-1   Static Electricity Guard
CARD FRONT
PBX
WRIST STRAP •  
WHEN PLUGGING/UNPLUGGING A CIRCUIT CARD
•  WHEN HOLDING A CIRCUIT CARD
FRAME GROUND SCREW
CONNECT THE GROUND WIRE TO THE 
FRAME EARTH OF THE EQUIPMENT.
NEVER TOUCH THE COMPONENTS 
OR SOLDERED SURFACE WITH
BARE HANDS. 

ND-46551 (E) CHAPTER 3
Page 21
Revision 2.0
Figure 3-1  Static Electricity Guard (Continued)
WEAR A WRIST STRAP AND PERFORM
THE WORK ON A GROUNDED
CONDUCTIVE WORK SURFACE.
WHEN CARRYING A CIRCUIT
CARD AROUND, KEEP THE
CARD IN A CONDUCTIVE
POLYETHYLENE BAG. CONDUCTIVE
POLYETHYLENE
BAG CIRCUIT
    CARDCIRCUIT
    CARD •  WHEN MAKING A SWITCH SETTING ON A CIRCUIT CARD
•  WHEN CARRYING A CIRCUIT CARD 

CHAPTER 3 ND-46551 (E)
Pag e 2 2
Revision 2.0
1.3 Removing/Inserting Circuit Cards
When removing a circuit card from the PIM or when inserting a circuit card in the PIM, follow the procedure in
Table 3-1. 
Table 3-1  Removing/Inserting Circuit Cards Procedure
CIRCUIT CARDPROCEDURE
CONDITION
INSERT REMOVE
•PN-CP03 (MP)
•PZ-PW86 (PWR)
• PN-PW00 (EXTPWR)Power off
¯
Insert
¯
Power onPower off
¯
Remove
¯
Power onAlways insert or remove these circuit cards 
with power off to prevent damage to the card 
or...

ND-46551 (E) CHAPTER 3
Page 23
Revision 2.0
CAUTION:Always hold the card name label area when inserting or removing a circuit card. Touching anoth-
er area may result in exposure to hazard voltages.
CARD FRONT
PBX
NEVER TOUCH THE COMPONENTS OR 
SOLDERED SURFACE WITH BARE 
HANDS. 

CHAPTER 3  ND -4 6551 ( E)
2. PR O CED URE
START
UNP ACKING
CA BLE RUNNING
SW ITCH  SETT ING
A
INST ALL AT IO N 

ND -4 6551 ( E)  CHAPTER 3
Fig u re 3-2    P ro ced ure F lo w ch art  (C ont inue d)
A
END
C LEANING
A TT EN TIO N 

CHAPTER 3 ND-46551 (E)
Pag e 2 6
Revision 2.0
NAP-200-001
Sheet 1/2
Unpacking
1. UNPACKING PROCEDURE
(1) Check the received quantity of packages containing the PBX system with the description on the shipping
document.
(2) Check the packaging for external damage done by transportation and record it as necessary.
(3) Unpack the packaging.
• For unpacking the packages containing circuit cards, a grounded wrist strap should be worn.
(4) Check the quantity of equipment and materials unpacked with the shipping...

ND-46551 (E) CHAPTER 3
Page 27
Revision 2.0
NAP-200-001
Sheet 2/2
Unpacking
Figure 001-1  Unpacking of Main Equipment
ACCESSORIES
PIM 

CHAPTER 3  ND -4 6551 ( E)
NAP-2 00-0 02
3 5 6  m m  (1 4.0  in ch)
4 3 0  m m  (1 6.9  in ch)
\
\
\
\
\
\
F R ONT
RACK PARTS
37  m m ( 1 .6  in ch)
40  m m ( 1 .6  in ch)
W ALL