NEC Neax2000 Ivs Small Platform System Manual

CHAPTER 2 ND-46551 (E)
Pag e 8
Revision 2.0
Figure 2-5   Desk Top Installation
PIM 

ND-46551 (E) CHAPTER 2
Page 9
Revision 2.0
3. FUNCTIONAL OUTLINE OF EQUIPMENT
This section explains the functional outline of the equipment (modules, installation hardware, circuit cards) used in
the PBX.
3.1 Functional Outline of Modules
Table 2-2 shows the functional outline of the modules.
Table 2-2  Functional Outline of Modules
MODULESFUNCTIONAL
NAMEFUNCTIONAL OUTLINE
SN1308 PIMQ-UA PIMPort Interface Module (PIM)
A PIM provides 13 card slot for common control, Line/Trunk, and Applica-
tion Processor...

CHAPTER 2 ND-46551 (E)
Pag e 1 0
Revision 2.0
3.2 Functional Outline of Installation Hardware
Table 2-3 shows the functional outline of installation hardware.
3.3 Functional Outline of Circuit Cards
3.3.1 Control Circuit Card
Table 2-4 shows the functional outline of each control circuit card.
Table 2-3  Functional Outline of Installation Hardware
INSTALLATION
HARDWAREFUNCTIONAL
NAMEFUNCTIONAL OUTLINE
SN1225 BASE-A BASEBase Unit (includes Top Cover)
The Base Unit and Top Cover is required for PIM.
RACK...

ND-46551 (E) CHAPTER 2
Page 11
Revision 2.0
3.3.2 Application Circuit Cards
Table 2-5 shows the functional outline of each application circuit card.
Table 2-5  Functional Outline of Application Circuit Cards  
CARD NAMEFUNCTIONAL 
NAMEFUNCTIONAL OUTLINE
PN-AP00-A AP00Application Processor card.
This card is equipped with four RS-232C ports, and is used for SMDR, H/M Printer, 
PMS functions and MCI.
This card is used on the basis of one per system.
PN-AP01 AP01Application Processor card. 
This card is...

CHAPTER 2  ND -4 6551 ( E)
3.3 .3   Lin e/T run k Ci rc ui t C ards 

ND -4 6551 ( E)  CHAPTER 2
PN-4DLCD/ 

CHAPTER 2  ND -4 6551 ( E)
Tab le  2-7   L ine  Con diti o n of E ach  T er mina ls 

ND -4 6551 ( E)  CHAPTER 2
*Th e v alue in th e [ ] s ho ws th e ca ble le ng th  wh en usin g th e long li ne  fun ction. 

CHAPTER 2 ND-46551 (E)
Pag e 1 6
Revision 2.0
4. CIRCUIT CARD INSTALLATION CONDITIONS
4.1 Circuit Card Mounting Slots
Figure 2-6 below shows circuit card mounting slots allocated in the PIM, on the basis of circuit card type.
Figure 2-6   Circuit Card Mounting Slots
LT00 - LT10 : Line/trunk circuit card mounting slots
• LT00 - LT08 : All of line/trunk circuit card can be mounted in these slots
• LT09 : All of line/trunk circuit card can be mounted in this slot
(But a maximum of 4 circuits can be assigned...

ND-46551 (E) CHAPTER 2
Page 17
Revision 2.0
4.2 Installation Conditions
(1) The application circuit cards PN-BRTA and PN-24DTA-A cannot be mounted in slots AP4 or AP5, since
neither of these slots has a connection to the MDF via the backplane.
(2) The application circuit card type PN-CC00 can be mounted in any LT/AP slot, but it occupies two slot po-
sitions; i.e. the slot immediately to its right must be vacant.
(3) The PN-PW00 can be mounted in any LT/AP slot, but it occupies two slot positions; i.e....