NEC Neax 2400 Ipx Wireless System Manual

CHAPTER 4 NDA-24301
Pag e 1 54
Revision 1.0
Figure 4-3  ATRK for 24DTI + 2DCH
 When #0 DCH of 2DCH card is used.
Note:Slot X and Slot Y must be in the same HW.
Odd
Number
Group
Even
Number
GroupLevel Slot X Slot YLV  7
6
5
4
3
2
1
LV  0
LV  7
6
5
4
3
2
1
LV  0
Bch   8
7
6
5
4
3
2
Bch   1
 Dch    1
Bch  23
22
21
20
19
18
17
16
15
14
13
12
11
10
Bch    9
IF 16 PORTS/SLOTGroup
  n+3
Group
  n+1
Group
  nLevel Slot
LV  7
6
5
4
3
2
1
LV  0
LV  7
6
5
4
3
2
1
LV  0LV  7
6
5
4
3
2
1
LV  0
LV  7
6
5
4
3
2
1
LV...

NDA-24301 CHAPTER 4
Page 155
Revision 1.0
Figure 4-4  ATRK for 30PRT
Note:Slot X and Slot Y must be in the same HW.
Odd
Number
Group
Even
Number
GroupLevel Slot X Slot YLV  7
6
5
4
3
2
1
LV  0
LV  7
6
5
4
3
2
1
LV  0
Bch   15
 
Bch    1
Dch    2Bch   30
Bch   16
Dch     1
IF 16 PORTS/SLOT Group
  n+3
Group
  n+1
Group
  nLevel Slot
LV  7
6
5
4
3
2
1
LV  0
LV  7
6
5
4
3
2
1
LV  0LV  7
6
5
4
3
2
1
LV  0
LV  7
6
5
4
3
2
1
LV  0Bch   30
Bch  16
Dch    1
Bch  15
Bch    1
Dch    2
IF 32 PORTS/SLOT  Group...

CHAPTER 4 NDA-24301
Pag e 1 56
Revision 1.0
Figure 4-5  ATRK for 30DTI + 2DCH
 When #0 DCH of 2DCH card is used.
Note:Slot X and Slot Y must be in the same HW.
Odd
Number
Group
Even
Number
GroupLevelLV  7
6
5
4
3
2
1
LV  0
LV  7
6
5
4
3
2
1
LV  0
IF 16 PORTS/SLOTGroup
  n+3
Group
  n+1
Group
  nLevel Slot
LV  7
6
5
4
3
2
1
LV  0
LV  7
6
5
4
3
2
1
LV  0LV  7
6
5
4
3
2
1
LV  0
LV  7
6
5
4
3
2
1
LV  0Dch   2
IF 32 PORTS/SLOT  Group
  n+2
Slot 
Dch   2Slot X Slot Y
Bch   15
 
Bch    1Bch   30
Bch   16
Dch...

NDA-24301 CHAPTER 4
Page 157
Revision 1.0
4) ADPC (Destination Point Code Data)
- Assign Point Code for both Bch route and Dch route.
- The values for a Point Code is 1 through 16383. You can assign any number as the Point Code  
for them, however, do not duplicate the Point Code which is used for No. 7 CCIS.
5) ACSC (CSC Data)
- Assign Dch and Bch location for CSCG.
- The values for CSCG is 130 through 255.
- Even number CSCGs are used for Dch location and odd number CSCGs are used for Bch 
location....

CHAPTER 4 NDA-24301
Pag e 1 58
Revision 1.0
2) Condition: 24DTI/30DTI is mounted in Slot 07 of PIM0 and 2DCH is mounted in Slot 05 of 
PIM0. ACSC data is as follows.
Note 1:The location of DCH (Dch Handler) must be assigned in parameter “CCH” of this
command.
Note 2:Above is an example when #0 DCH of PA-2DCH circuit card is used.
6) ACIC1 (CIC Code Data1)
- With respect to PC assigned in the ADPC command, assign CSCG of the Dch assigned in the 
ACSC command.
7) ATRK (Trunk Data)
- Assign Dch trunk data...

NDA-24301 CHAPTER 4
Page 159
Revision 1.0
TWO-LINE OPERATION
1. GENERAL DESCRIPTION
This feature allows for the appearance of two lines on the line (L1 and L2) keys of the PS.
2. OPERATING PROCEDURE
No manual operation is required.
3. SERVICE CONDITIONS
1. This feature is available for Series 7300 or later software.
2. Two kinds of lines can appear on the PS: My Line and  Sub Line.  These lines are associated with the station
numbers assigned to the port on the interface circuit.
L1 key: My Line
L2 key:...

CHAPTER 4 NDA-24301
Pag e 1 60
Revision 1.0
5. PROGRAMMING
1) APSD (Assignment of the PS Operation Data for DM)
This command assigns the PS operation data including its tenant No., station No., Service Feature 
Restriction Class (SFC) and the Route Restriction Class (RSC) in consideration of the numbering 
plan/restriction data. Assign My Line and Sub Line data of the PS.
 TN : Tenant
 PSTN : PS STN
 KIND : PS KIND : Assign 6 (D
term-PSII) for My Line.
Assign 7 (Dterm-PSII Sub Line) for Sub Line.
...

NDA-24301 CHAPTER 4
Page 161
Revision 1.0
VOICE MAIL INDICATION (VMI)
1. GENERAL DESCRIPTION
This feature provides ON/OFF control of the Voice Mail Message (VMM) indication of the PS (including the
PS in a visitor node) via Message Center Interface (MCI). This feature is also available in the CCIS and
Netfusing networks.
There are two types of notification methods: active notification and passive notification.
Active notification:The notification is given when a voice message is received.
Passive...

CHAPTER 4 NDA-24301
Pag e 1 62
Revision 1.0
ZT PROGRAM DOWNLOAD
1. GENERAL DESCRIPTION
This feature allows maintenance personnel to update the ZT program by command operation. Accordingly, only
one ZT needs to be updated by the dedicated tool.
2. OPERATING PROCEDURE
1. Using the dedicated tool, write new program into a ZT. This ZT is called “Program Master ZT”.
2. Connect “Program Master ZT” to the system.
3. Download new program from “Program Master ZT” to the other ZTs, called “PROGRAM DOWNLOAD
ZTs”,...

NDA-24301 CHAPTER 4
Page 163
Revision 1.0
4. PROGRAMMING
1) ACSDL (Assignment for CS/ZT Data for LDM)/ACSDN (Assignment for CS/ZT Data for NDM)
This command is used to assign the ZT related data including the PHS Community Number,
Calling Area No., Group No., ZT NO., ZT LENS, and ZT KIND.
When this data assignment is finished, 3B+D channels of the CSINT circuit card start up.
 PHS Community Number: 1-1024
 Calling Area Number: 1-32
 Group Number: 1-8
 ZT Number: 1-32
 TN: Tenant Number
 LENS: ZT...