NEC Neax 2400 Ipx Wireless System Manual

CHAPTER 4 NDA-24301
Pag e 1 14
Revision 1.0
OFFICE DATA ASSIGNMENT
5) ARRC (Alternative Route Restriction Pattern Data)
Allow the restriction between the external trunk and the announcement trunk.
ICRT : Incoming Route Number
OGRT : Outgoing Route Number (Announcement trunk)
ARI-D_RES = 1 (Tandem Connection without an operator/station assistance is allowed)
6) AAED (Announcement Equipment Data)
Assign EQP=60 for the AUTOMATIC ANNOUNCEMENT-PS OUT OF ZONE
TN : Tenant Number
EQP = 60 (AUTOMATIC...

NDA-24301 CHAPTER 4
Page 115
Revision 1.0
OFFICE DATA ASSIGNMENT
4-2 C.F.-PS Incoming Incomplete
 Entry Procedures
1) ASYD (Assignment for System Data)
Assign whether to use a same access code for Call Forwarding-Busy Line, Call Forwarding-Don’t 
Answer and C.F.-PS Incoming Incomplete, or use separate access codes.
SYS1, INDEX5, bit 0
0=Same
1=Separate
2) ANPD (Numbering Plan Data)
Assign the necessary number of digits needed to determine the service which is required according 
to the first digit...

CHAPTER 4 NDA-24301
Pag e 1 16
Revision 1.0
OFFICE DATA ASSIGNMENT
AUTOMATIC ANNOUNCEMENT-DISCONNECTED PS OUT OF ZONE
1. GENERAL DESCRIPTION
When a PS user moves Out of Zone (out of the PCS service area) and the call is disconnected, the counterpart
hears the announcement stating the call was disconnected due to the the wireless user going Out of Zone.
2. OPERATING PROCEDURE
No manual operation
3. SERVICE CONDITIONS
1. This service is valid only in a two-party call.
This service cannot be used when a...

NDA-24301 CHAPTER 4
Page 117
Revision 1.0
OFFICE DATA ASSIGNMENT
4. PROGRAMMING
 Entry Procedures
1) ARTD (Route Class Data)
Assign the Route Class Data of the announcement trunk.
RT : Route Number
OSGS (CDN: 1) = 2
ONSG (CDN: 2)= 2
TF (CDN: 5) = 1
TCL (CDN: 6) = 4
L/T (CDN: 7) = 1
ANS (CDN: 28) = 1
Assign “0” for other data.
2) ALRTN (Assignment of Logical RT in Network Data Memory)
LGRT : Logical Route Number
FPC : Fusion Point Code
RT : Route Number
Note:Not necessary in a standalone type.
3) ATRK...

CHAPTER 4 NDA-24301
Pag e 1 18
Revision 1.0
OFFICE DATA ASSIGNMENT
3) MBTK (Make Busy of Trunk)
Set the announcement trunk in a make-busy cancel state
4) ARSC (Route Restriction Class Data)
Assign the Route Restriction Class of the station which allows access to the announcement trunk.
D/N : Day/Night Mode
TN : Tenant Number
RT : Route Number
RSC : Route Restriction Class (0-15)
RRI :  Route Restriction Index (0-3)
RES = 1 (Allowed)
5) ARRC (Alternative Route Restriction Pattern Data)
Allow the...

NDA-24301 CHAPTER 4
Page 119
Revision 1.0
OFFICE DATA ASSIGNMENT
NAME DISPLAY
1. GENERAL DESCRIPTION
This feature allows a PS to indicate the user information corresponding to the calling station number while
engaged in a station-to-station call.
2. OPERATING PROCEDURE
Examples of LCD display are shown below.
 When originating a station-to-station call:
LCD display of the calling station:
LCD display of the called station:
 When a station call has been transferred to another station by Call...

CHAPTER 4 NDA-24301
Pag e 1 20
Revision 1.0
OFFICE DATA ASSIGNMENT
3. SERVICE CONDITIONS
1. This feature is available for Series 7300 or later software.
2. User information corresponding to the station number that can be displayed on the LCD is a maximum of
16 digits.
3. User information is displayed on the LCD, intended to the left. The information may consist of upper case
letters, numeric characters, and most keyboard symbols.
4. When user information is 12 digits or more, the first or last part of...

NDA-24301 CHAPTER 4
Page 121
Revision 1.0
OFFICE DATA ASSIGNMENT
4. PROGRAMMING
1) ASYD (Assignment of System Data)
SYS1
SI 78
b5: 1 (Name Display In Service)
SI 79
b6: 0 (OAI In Service)
SI 241
b1: The number of digits displayed in NAME DISPLAY service
0/1: 8 digits/16 digits
2) ANDD (Assignment of Name Display Data)
Assign user’s information to Physical Station Number.
TN : Tenant Number
STN : Physical Station Number
NAME : User information (Maximum 16 digits)
 END
 START 

CHAPTER 4 NDA-24301
Pag e 1 22
Revision 1.0
OFFICE DATA ASSIGNMENT
NAME DISPLAY - CCIS
1. GENERAL DESCRIPTION
In between CCIS nodes, this feature allows calling or called party information to be displayed on the LCD of a
PS.
2. OPERATING PROCEDURE
Examples of LCD display are shown below.
 When originating a call:
LCD display of the calling station:
LCD display of the called station:
 When a call has been transferred to another station by Call Forwarding-All Calls/Busy Line/Don’t Answer/
PS-Incoming...

NDA-24301 CHAPTER 4
Page 123
Revision 1.0
OFFICE DATA ASSIGNMENT
3. SERVICE CONDITIONS
1. This feature is available for Series 7300 or later software.
2. User information corresponding to the station number that can be displayed on the LCD is a maximum of
16 digits.
3. User information is displayed on the LCD, intended to the left. The information may consist of upper case
letters, numeric characters, and most keyboard symbols.
4. When user information is 12 digits or more, the first or last part of...