NEC Neax 2400 Ipx Wireless System Manual

CHAPTER 4 NDA-24301
Pag e 1 64
Revision 1.0
CALL FORWARDING - DROPPED CALLS
1. GENERAL
This feature provides a call forwarding function when a PS encounters a Squelch Disconnection (such as PS
moving out of zone, failing to hand over a call, or a sudden power down of the PS) during a two-way connection
with a station/trunk. If this feature is set, the PS can forward the unexpectedly disconnected call to a pre-assigned
forwarding destination, such as a PS, a user of voice mail system, or an analog/D
term...

NDA-24301 CHAPTER 4
Page 165
Revision 1.0
3. SERVICE CONDITIONS
1. This feature can be set at each PS, that is already provided with the C.F.-PS INCOMING INCOMPLETE
feature.
2. The forwarding destination of C.F.-PS INCOMING INCOMPLETE is also designated as the destination of
this feature.
3. This feature can be cancelled also by cancelling C.F.-PS INCOMING INCOMPLETE. However, if the
following is set, C.F.-PS INCOMING INCOMPLETE is cancelled, while this feature is maintained:
ASYD command, SYS 1, Index...

CHAPTER 4 NDA-24301
Pag e 1 66
Revision 1.0
- After a certain period of no answer, the call is shifted to the destination of CALL FORWARDING - DON’T
ANSWER.
[When CALL FORWARDING - DON’T ANSWER is not assigned at the forwarded party]
- Recall to the Squelch PS is not made, and the forwarded party continues to ring. 
15. When a call is forwarded by this feature and also is shifted to another destination, the forwarding kind to be
notified to the destination is “C.F.-PS INCOMING INCOMPLETE”.
16. When this...

NDA-24301 CHAPTER 4
Page 167
Revision 1.0
4. The Call Waiting service is available for the call forwarded by this feature.
5. When a PS moves to a visitor PBX (when roaming) and it encounters a Squelch Disconnection, this feature
is not activated.

None
5. PROGRAMMING
 Entry Procedures
1) ANPD (Assignment of Numbering Plan Data) 
Assign 1st digit code (1st DC) and number of necessary digits (NND) for feature access and 
cancel. 
2) ASPA (Assignment of Special Access Code Data) 
Assign the access code...

CHAPTER 4 NDA-24301
Pag e 1 68
Revision 1.0
AUTHORIZATION CODE 
1. GENERAL DESCRIPTION
An AUTHORIZATION CODE is a numerical code dialed by PS users (up to ten digits), which will override the
station CLASS OF SERVICE - INDIVIDUAL [C-15] for facility access restriction. 
2. OPERATING PROCEDURE
Procedure 1
 With a feature Access Code
1) Go off-hook and receive Dial Tone. 
2) Enter the feature Access Code and receive Service Set Tone.
3) Enter the AUTHORIZATION CODE (up to ten digits).
4) Receive Dial...

NDA-24301 CHAPTER 4
Page 169
Revision 1.0
3. SERVICE CONDITIONS
1. The following service feature restriction classes cannot be overrided by using feature.
 SFI=125(PAD LOCK)
 SFI=137(Authorization Code Display Elimination)
2. The followings are conditions of this feature when using My Line (L1) and Sub Line (L2) simultaneously.
(Tow-Line Operation)
 When holding a line, the held line becomes class before changeover, and then after return to original
call, the class becomes changed class.
 When both...

CHAPTER 4 NDA-24301
Pag e 1 70
Revision 1.0
System Data 1, Index 13. Each Bit in Index 13 directly correlates to a digit in the 
AUTHORIZATION CODE assigned in AATC, and will determine the second digit of the 
Checksum method. Pick any Bits 0 - 4, but not the same combination of Bits as picked in Index 12.
System Data 1, Index 14 determines the algorithm used to calculate the last two digits of every 
AUTHORIZATION CODE. (Only decimal numbers may be used in this index, therefore, 
hexadecimal values A to...

NDA-24301 CHAPTER 4
Page 171
Revision 1.0
ASYD - System Data 1, Index 43, Bit 2, is Service Set Tone sent after AUTHORIZATION CODE.
ASPA access code? 0/1: No/Yes. Assign data “1”.
System Data 1, Index 43, bit 0, is AUTHORIZATION CODE required for DISA? 0/1: required/
not required. Normally assign data “0.”
System Data 1, Index 93, Bit 6. Are the AMND tables Separate or Common for tenants in the 
system? 0/1: Separate/Common. Assign data “0” for separate tables. 
System Data 2, Index 3, Bit 4: Is Account...

CHAPTER 4 NDA-24301
Pag e 1 72
Revision 1.0
CALL PARK
1. GENERAL DESCRIPTION
This feature enables a PS user to “Park” a call (C. O. line, Tie line, station, PS) by hooking and dialing a Call
Park Access Code, and by dialing the Call Park retrieval code and a station number that parked the call, the
parked call can easily be retrieved from any station/PS within the system. If the user forgets to retrieve the
parked call, automatic recall function informs the user.
2. OPERATION PROCEDURE
To park a call...

NDA-24301 CHAPTER 4
Page 173
Revision 1.0
When access code operation that using enbloc sending is valid. (SYS1 INDEX420 bit 0=1)
1) Dial the Call Park remote retrieval code (SID=63) and the number of the station that parked the call.
2) Go off-hook.
3) The parked call is reconnected.
3. SERVICE CONDITIONS
1. This feature is also available for Sub Line (L2) of a two-line Dterm PS. (By using Two-Line Operation)
2. The parked PS cannot hold a terminal.
3. A PS can park only one call at the same time.
4. A...