NEC Neax 2400 Ipx Wireless System Manual

CHAPTER 5 NDA-24301
Pag e 1 94
Revision 1.0
COMMANDS
*ANSDNAssignment of Number Sharing Data for Network Data Memory
APMDAssignment of Trunk Line Appearance Maximum Necessary Digit for DM
APMLLAssignment of PS Multiline Data for Local Data Memory
APMLNAssignment of PS Multiline Data for Network Data Memory
APSPAssignment of Trunk Line Appearance for DM
AZDLZT Program Download
AHLGAssignment of CFT Hot Line Group
AHLGLAssignment of CFT Hot Line Group for LDM
AHLGNAssignment of CFT Hot Line Group for NDM...

NDA-24301 CHAPTER 5
Page 195
Revision 1.0
COMMANDS
1. COMMAND DESCRIPTION AND DA T A   S H E E T   F O R   A S S I G N M E N T
This chapter explains assignment commands and their parameters for this system. The contents of each
assignment command description are illustrated in Figure 5-1.
Figure 5-1  Command Descriptions
Command name
The assigned data dump  into the designated file by the 
list up command shown here.Command name (full name)
The purpose of command and the related service
feature are...

CHAPTER 5 NDA-24301
Pag e 1 96
Revision 1.0
ACSDL  : Assignment of CS/ZT Data for Local Data Memory
1. GENERAL
This command is used to assign, delete, and display the CS/ZT-related data. A CSINT circuit card can
accommodate four CSs/ZTs, allowing each two groups of the Levels 0 and 4 to be assigned for one circuit card.
List Up Command: LCSDL
2. PRECAUTIONS
1. This command is used for the Local Node.
2. When assigning LENS, CS/ZT should be assigned in the Group of less than 24 and the Levels to be...

NDA-24301 CHAPTER 5
Page 197
Revision 1.0
4. DATA SHEET
CS/ZT Data Assignment Sheet
PHS 
COMMUNITY 
NUMBER
(PCN)
1-1024CALLING 
AREA NO.
(ERN)
1-32GROUP 
NO.
(GRN)
1-8CS/ZT 
NO.
(CSN/
ZTN)
1-32TENANT 
NUMBER
(TN)
1-
SYSTEM 
MAXLENS
CS/ZT 
KIND
(KIND)
3, 4 MG 
00-07U
0-3G
00-23LV  
0/4 

CHAPTER 5 NDA-24301
Pag e 1 98
Revision 1.0
ACSDN  : Assignment of CS/ZT Data for Network Data Memory
1. GENERAL
This command is used to assign, delete and display the CS/ZT-related data of the Network Control Node (NCN).
A CSINT circuit card can accommodate four CSs/ZTs, allowing each two groups of the Levels 0 and 4 to be
assigned for one circuit card.
List Up Command: LCSDN
2. PRECAUTIONS
1. This command is used for the Network Control Node.
2. When assigning LENS, CS/ZT should be assigned in the...

NDA-24301 CHAPTER 5
Page 199
Revision 1.0
3. DATA ENTRY INSTRUCTIONS
PCN
GRN
Enter the PCN (PHS Community Number)
Note: Group NO. available for inter-node
           of the Fusion Network
Enter the GRN (Group 
Number)TN
Enter the TN (Tenant Number)
PHS
COMMUNITY
NUMBER
 ( PCN )
1 - 1024FUSION
POINT CODE
( FPC )
1 - 253CALLING 
AREA
NUMBER
 ( ERN )
1 - 32GROUP
NUMBER
 ( GRN )
1 - 8TENANT
NUMBER
( TN )
1-SYSTEM MAX
EQUIPMENT
NUMBER
( LENS ) CS / ZT  
NUMBER
 ( CSN / ZTN )
1 - 32CS / ZT  KIND
 ( KIND )
1 -...

CHAPTER 5 NDA-24301
Pag e 2 00
Revision 1.0
4. DATA SHEET
CS/ZT Data Assignment Sheet
PHS 
COMMUNITY
NUMBER
(PCN)
1-1024FUSION
POINT CODE
(FPC)
1-253CALLING 
AREA 
NO.
(ERN)
1-32GROU
P NO.
(GRN)
1-8CS/
ZT 
NO.
(CSN
/
ZTN)
1-32TENANT 
NUMBER
(TN)
1-
SYSTEM 
MAXLENS
CS/
ZT
KIND
(KIND)
3, 4 MG 
00-07U
0-3G
00-23LV
0/4 

NDA-24301 CHAPTER 5
Page 201
Revision 1.0
ACSEL  : Assignment of Expansion CS/ZT System Data for Local Data Memory
1. GENERAL
This command is used to assign, delete and display the expansion CS/ZT System data in Local Node.
List Up Command : LCSEL
2. PRECAUTIONS
1. This command is used to the Local Node.
2. Enter “0” when you make the corresponding parameter invalid (NWNO., ADERA, CTRN).
3. This command can be used to change the data.
3. DATA ENTRY INSTRUCTIONS
 
PCN
ADERAEnter the PCN (PHS Community...

CHAPTER 5 NDA-24301
Pag e 2 02
Revision 1.0
4. DATA SHEET
Expansion CS/ZT System Data Assignment Sheet
PHS COMMUNITY 
NUMBER
(PCN)
1-1024NETWORK NO.
(NWNO.) 
0001-FFFFADD AREA
(ADERA) 
01-FFCOUNTRY NO. 
(CTRN)NUMBER OF
PHS-MANAGER CODE 
(NPCD)
0-4
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0 

NDA-24301 CHAPTER 5
Page 203
Revision 1.0
ACSEN  : Assignment of Expansion CS/ZT System Data for Network Data Memory
1. GENERAL
This commands is used to assign, delete, and display the expansion CS/ZT System data in Network Data
Memory.
2. PRECAUTIONS
1. This Command is used for the Network Control Node.
2.  Enter “0” when you make the corresponding parameter invalid (NWNO, ADERA, CTRN).
3. This command can be used to change the data.
3. DATA ENTRY INSTRUCTIONS
PCN
ADERAEnter the PCN (PHS Community...