NEC Neax 2400 Ipx Wireless System Manual

CHAPTER 4 NDA-24301
Pag e 1 04
Revision 1.0
OFFICE DATA ASSIGNMENT
1. ZT Initial Start-Up
1) ASYD (Assignment of System Data)
CCIS ISDN function simultaneously becomes valid when the ZT operation is attempted to be in 
service, as the ZT is regarded as a terminal of the ISDN.
SYS1
SI186 
Note 1
b6=1 (CCIS function in service)
SI220 
Note 1
b6=0 (ISDN function in service)
Note 1:ISDN and CCIS data become valid, but where the ISDN and CCIS functions are not to be
used, optional software concerning ISDN and...

NDA-24301 CHAPTER 4
Page 105
Revision 1.0
OFFICE DATA ASSIGNMENT
2. Procedure to Add Operating ZT7) ACSDN (Assignment of CS/ZT Data for Network Data Memory)
This command is used to assign the ZT related data including the PHS Community No., Fusion 
Point Code, Calling Area No., Group No., ZT No., ZT LENS, ZT KIND.
When this data assignment is finished, 3B+D channels of the CSINT circuit card start-up.
 PHS Community Number : 1~1024
 FPC : Fusion Point Code
 Calling Area Number : 1-32
 Group Number :...

CHAPTER 4 NDA-24301
Pag e 1 06
Revision 1.0
OFFICE DATA ASSIGNMENT
3. ZT Deletion Procedure
1) MBCSN ( MAKE BUSY CS/ZT for Network Data Memory)
2) ACSDN (Assignment of CS/ZT Data for Network Data Memory)
Delete the ZT Data.
 START
 END 

NDA-24301 CHAPTER 4
Page 107
Revision 1.0
OFFICE DATA ASSIGNMENT
2.3 PS OFFICE DATA ASSIGNMENT
Below are explanations about assigning office data to place the PS in operation in the Built-in PCS system.

The port is automatically occupied for each PS assignment from the bigger numbered port (MG=31,U=3, G=23,
Level=7) to the smaller. When adding UNIT to the system later, you must concern about the number of assigned
PS (for example, if 192 PSs are assigned, the biggest numbered UNIT can not be used for...

CHAPTER 4 NDA-24301
Pag e 1 08
Revision 1.0
OFFICE DATA ASSIGNMENT
1) AFMU
Note:When a PS is assigned by APSD command, logically it occupies a port from module group
(MG) 31 to 26, from larger number of MG to smaller. Using AFMU command, those MGs must
be assigned for Fusion Network.
Since One MG can contain up to 768 PSs in it, for instance. If you need maximum of 4000 PSs
in a node, MG31, 30, 29, 28, 27 and 26 must be assigned.
At the beginning of installation, you do not have to allocate all six MGs...

NDA-24301 CHAPTER 4
Page 109
Revision 1.0
OFFICE DATA ASSIGNMENT
3. Deletion of the PS data
1) ALGSN (Assignment of Telephone Number Data for Network Data Memory)
Delete the Telephone Number and LENS related.
2) APSD (Assignment of the PS Operation Data for DM)
Using this command, delete the PS data to be cleared such as tenant No., station No., SFC and 
RSC.
Note:If CBCN has never been done in Fusion Network after the last initialization, please do CBCN
before ALGSN.
 END
 START 

CHAPTER 4 NDA-24301
Pag e 1 10
Revision 1.0
OFFICE DATA ASSIGNMENT
3.  ASSIGNM ENT  OF  SER VICE  F E ATURE  DATA
This section describes how to assign  the data for the  following serv ice features.
 Automatic Announcement-PS Out of Zone/C.F.-PS Incoming Incomplete
 Automatic Announcement-Disconnected PS Out of Zone
 Name Display
 Name Display-CCIS
 Number Sharing
PCS Roaming
 TTC Q. 931a protocol Tie Line with PCS Roaming
 Two-Line Operation
 Voice Mail Indication (VMI)
 ZT Program Download
...

NDA-24301 CHAPTER 4
Page 111
Revision 1.0
OFFICE DATA ASSIGNMENT
AUTOMATIC ANNOUNCEMENT-PS OUT OF ZONE/C.F.-PS INCOMING INCOMPLETE
1. GENERAL DESCRIPTION
When a call cannot terminate to a PS which is Out of Zone or whose power is OFF, the system automatically
answers the call and provides an announcement to notify the calling party that the called PS is Out  of Zone or
if the C.F.-PS Incoming Incomplete is set to a given destination, the aborted call can be transferred to the
preprogrammed station or...

CHAPTER 4 NDA-24301
Pag e 1 12
Revision 1.0
OFFICE DATA ASSIGNMENT
10. The incoming incomplete call to PS can be transferred to other PSs, stations, Attendant Consoles, Central
Office and TIE lines when the C.F.-INCOMING INCOMPLETE is in service.
11. The timer value of incoming incomplete call is approximately eight seconds, time duration until the system
recognizes that the PS is Out of Zone from an incoming call attempt to the PS.
Priority is given to the C.F.-INCOMING INCOMPLETE over the C.F.-DON’T...

NDA-24301 CHAPTER 4
Page 113
Revision 1.0
OFFICE DATA ASSIGNMENT
4. PROGRAMMING
4-1 Automatic Announcement-PS Out of Zone
 Entry Procedure
1) ARTD (Route Class Data)
Assign the Route Class Data for announcement trunk.
RT : Route Number
OSGS (CDN: 1) = 2
ONSG (CDN: 2) = 2
TF (CDN: 5) = 1
TCL (CDN: 6) = 4
L/T (CDN: 7) = 1
ANS (CDN28) = 1
Assign “0” for other parameters.
2) ALRTN (Assignment of Logical RT for Network Data Memory)
LGRT : Logical Route Number
FPC : Fusion Point Code
RT : Route Number...