NEC Neax 2400 Ipx Wireless System Manual

CHAPTER 3 NDA-24301
Pag e 5 4
Revision 1.0
CIRCUIT CARDS
PA-4CSIC (CSINT) : ZT (Zone Transceiver) Interface
Table 3-1  Switch Setting Table
MODULE
NAMESLOTSWITCH 
NAMESWITCH SHAPE REMARKS
PIM MB ON : Make-busy set of circuit 
card 
OFF : Make-busy cancel of 
circuit card
MBR
MODE
SW10
SW11
SW12
SWL0
SWL1
SWL2
SWL3
ON (MB)
OFF
No. 3
No. 2
No. 1
No. 0OFF
ON
ON
12
34
ON
12
3456
78
ON
12
3456 78 

NDA-24301 CHAPTER 3
Page 55
Revision 1.0
CIRCUIT CARDS
6. External interface
Below are accommodation of the LT connector leads of this circuit card and connecting route diagram.
a. LT Connector Lead Accommodation when this circuit card is mounted in PIM.
Figure 3-3  LT Connector Leads Accommodation of PIM : PA-4CSIC
26272829303132333435363738394041
1234567891011121314151642434445464748
1718192021222349502425
Accommodated in *1
LT0, 2, 4, 6, 8, 10 Connector
LT Connector Accommodation...

CHAPTER 3 NDA-24301
Pag e 5 6
Revision 1.0
CIRCUIT CARDS
Figure 3-4  Connecting Route Diagram
PBX
CSINT
TA
TB
RA
RBRA
RB
TA
TB
ZT IN
OUT MDF 

NDA-24301 CHAPTER 3
Page 57
Revision 1.0
PA-4CSID (CSINT)  : ZT (Zone Transceiver) Interface
1. General Functions
This card is a line circuit card which accommodates Zone Transceivers (ZTs) via the ISDN U interface. ZTs
are to be connected using NT1.
The main specifications and functions of this circuit card are shown below.
 A maximum number of four ZTs can be accommodated in one circuit card.
 Interface with the NT1 is based on the standard ISDN interface. (U reference-point Echo Canceller
method....

CHAPTER 3 NDA-24301
Pag e 5 8
Revision 1.0
3. Lamps, Switches, Connectors and Their Location
The following diagram shows the location of Lamp, Key and Connectors.
Figure 3-6  Lamp, Key and Connectors : PA-4CSID
OPE
MB
MODE
SW21NOPE
MBRL3
L2
L1
L0 SW12
SW11
SW20
SW10LPB
L3
L2
L1
L0
MONITOR (Not used)
BL34
BER3 BL33
LYR3 BL32
BL31
BL24
BER2 BL23
LYR2 BL21
BL22
BL14
BER1 BL13
BL12
LYR1 BL11
BL04
BER0 BL03
BL02
LYR0 BL01 

NDA-24301 CHAPTER 3
Page 59
Revision 1.0
4. Lamp Indication
Shown below are the contents of lamp indication on this circuit card.
n=0~3
Note 1:B1 through B4 channels represent channel names of 32K ADPCM.
Note 2:Establishment of synchronization on U Reference Point may take 30 seconds or more.
LAMP NAME COLOR MEANING
OPE Green Remains lit when the card is operating normally.
NOPE Red Remains lit when the card is in make-busy state.
BLn4Green  Remains lit when B4 channel of the line #n is communicating  (...

CHAPTER 3 NDA-24301
Pag e 6 0
Revision 1.0
5. Switch Settings
Switches on this card have the following meanings.
SWITCH NAMESWITCH 
NUMBERSWITCH 
SETTINGSTANDARD 
SETTINGMEANING
MB
 (Toggle Switch)
UPCircuit card make-busy
DOWN×Circuit card make-busy cancel
MBR
 (Piano Switch)
0ON Line 0 make-busy request
OFF×Line 0 make-busy request cancel
1ON Line 1 make-busy request
OFF×Line 1 make-busy request cancel
2ON Line 2 make-busy request
OFF×Line 2 make-busy request cancel
3ON Line 3 make-busy request...

NDA-24301 CHAPTER 3
Page 61
Revision 1.0
SWITCH NAMESWITCH 
NUMBERSWITCH
SETTINGSTANDARD 
SETTINGMEANING
SW11 
1PAD on TSW side
2
3ON×Fixed
4ON×Fixed
5ON×PB Sender Mode (Law/Level)
Note:µ/A-law can be selected on the TSW side
PA D .
µ-law standard = High: –7.0 dBm
Low: –9.0 dBm
A-law standard = High: –8.0 dBm
Low: –10.0 dBm OFF
6ON×
OFF
7ON×
Not used
8ON Sealing Current is not supplied.
OFF×
Sealing Current is supplied.
(DIP Switch)
ON
12
3456
78SW1 SW2 PAD
OFF OFF Not used
ON OFF Not used
OFF ON A-law...

CHAPTER 3 NDA-24301
Pag e 6 2
Revision 1.0
Note 1:PAD control is shown below. Note that Echo Canceller, PAD 3 and PAD 4 are bypassed when the MODE
switch is set to “0”.
Note 2:Regarding speech communication, PAD values set on SW12-1 through SW12-6 are applied. In the other
cases (ex. data communication), PAD values are set according to the order of CPU.
[Firmware: SW-330]
SWITCH NAMESWITCH 
NUMBERSWITCH 
SETTINGSTANDARD 
SETTINGMEANING
SW12
(DIP Switch)1~3PAD control (TSW Side PAD Value)  
Note 1
4~6PAD...

NDA-24301 CHAPTER 3
Page 63
Revision 1.0
[Firmware: SW-360]
Note 1:PAD control is shown below. Note that Echo Canceller, PAD 3 and PAD 4 are bypassed when the MODE
switch is set to “0”.
Note 2:Pad value of both PAD 1 and PAD 2 is 0 dB.
SWITCH NAMESWITCH 
NUMBERSWITCH 
SETTINGSTANDARD 
SETTINGMEANING
SW12
(DIP Switch)
1~8
Connection with C.O. if Echo Canceller is not effective. Note 1  Connection with C.O. if Echo Canceller is  effective. Note 2
ON
12
3456 78
Connection with station if Echo Canceller is...