NEC Neax 2400 Ipx Wireless System Manual

CHAPTER 1 NDA-24301
Page 4
Revision 1.0
GENERAL DESCRIPTION
3. MOVEMENT OF PS IN NEAX2400 IPX
PCS COMMUNITY
The SYS-ID is a unique ID which was given to manage the PCS system. The area where the SYS-ID is effective
is called PCS Community. Every PCS Community in a Fusion network is given a unique PHS Community
Number (PCN). Each PCN has its own SYS-ID. The PCN is used in stead of the SYS-ID for MAT command,
and this can reduce the effect upon changing the SYS-ID to some measure. The habitual operation of...

NDA-24301 CHAPTER 1
Page 5
Revision 1.0
GENERAL DESCRIPTION
Fusion-I
A
B
C
D
Home PCN-a
Home
 PCN-b
Fusion-II
EF Visit PCN-c
        Visit
 PCN-d
G
 Node-WNode-XNode-YNode-Z
FCCS
Q. 931a or IS-11572 Note 
FCCS
Note:Node-W and Node-Y are connected with Q. 931a or IS-11572.
A, B
Home Node
Home PCNC, D
Visit Node
Home PCNE
Visit Fusion
Visit Node
Visit PCNF
Visit Fusion
Other Node
Visit PCNG
Ye t  O th e r
Fusion
A, B
Home Node
Home PCNStand-by condition 
Movement
H-OStand-by condition 
Movement
H-ORoaming...

CHAPTER 1 NDA-24301
Page 6
Revision 1.0
GENERAL DESCRIPTION
4. SYSTEM CAPACITY
The following explains the capacity of the System.
Note 1:Depending on capacity of NDM/LDM.
When upgrading from ICS and re-using Data Memory, Maximum 2000 terminals/Node.
Note 2:A maximum of 12 circuit cards can be mounted in a PIM.

A maximum of 9,000 PS terminals can be accommodated in a system.
5. MOUNTING LOCATION OF CSINT CIRCUIT CARD
CSINT circuit card can be mounted in any universal slot in the PIM.
Table 1-1  System...

NDA-24301 CHAPTER 1
Page 7
Revision 1.0
GENERAL DESCRIPTION
6. FUNCTIONS/MOUNTING CONDITIONS OF CIRCUIT CARDS
The following circuit cards are necessary when using the system.
1. Universal LC/TRK circuit cards
ABBREVIATIONCIRCUIT 
CARD NAMEFUNCTIONS AND MOUNTING CONDITIONS
RST PA-8RSTJ/
PA-8RSTMRegister-Sender 
As is the case with the RST functions in the normal stations, the RST is used 
virtually, and estimating how many lines are needed is as important as 
considering the number of terminals. 
Refer to...

CHAPTER 1 NDA-24301
Page 8
Revision 1.0
GENERAL DESCRIPTION
CLK PH-CK18
(IPX-U
System)This card is used for the Local Node of the IPX-U system. This card receives 
clock signals from the Phase Lock Oscillator (PLO) accommodated in 
TSWM0 of IMG1, distributing the following signals to Time Division Switch 
(TSW) accommodated in TSWM1 of IMG2.
32.768 MHz CLK
8 KHz FH
5 msec × “n” FH
SYNC PA-CK16 This circuit card is used for 5 ms synchronization between CSINTs (Clock 
Source Office and Subordinate...

NDA-24301 CHAPTER 1
Page 9
Revision 1.0
GENERAL DESCRIPTION
CFT PA-CFTB 8-Party Conference Trunk
Used SP388 (firmware) for GROUP CALL-AUTOMATIC CONFERENCE 
Used SP1141 (firmware) for GROUP CALL-AUTOMATIC 
CONFERENCE  (20-party). Refer to the “Circuit Card Manual” for SW 
setting.
ABBREVIATIONCIRCUIT 
CARD NAMEFUNCTIONS AND MOUNTING CONDITIONS 

CHAPTER 1 NDA-24301
Page 10
Revision 1.0
GENERAL DESCRIPTION
7. SERVICE CONDITIONS
Below are some of the conditions for using the System.
1. The system is available in the Business/Hotel System.
2. ACD/OAI services are incompatible with the system.
3. The following software is necessary for system operation.
Basic software: Series 7300 or later
Optional software: Service (Application) software including PCS service.  
Note 
Note:
When using PCS in Fusion Network, this software must be installed in all...

NDA-24301 CHAPTER 1
Page 11
Revision 1.0
GENERAL DESCRIPTION
8. LIST OF SERVICE FEATURES
1. PCS Feature
Table 1-2  List of Wireless Features
SERVICE FUNCTIONS REMARKS
UNUSED NUMBER
PS LOCATION 
REGISTRATION
OG CALL TO OUTSIDE Least Cost Routing (LCR) is the only dialing method valid in OG call to 
outside.
Note 1:For Fusion Network, this feature is available for Series 7300
Release 3 or later software.
INDIVIDUAL PS CALLING Incoming calls can be terminated to a PS only in the area where the...

CHAPTER 1 NDA-24301
Page 12
Revision 1.0
GENERAL DESCRIPTION
Note 3:
Handover
1) If a PS user moves to another zone that has all speech channels busy, the PS remains connected to the
original ZT.
2) Speech is temporarily interrupted during handover.
3) PS is unable to hand over in the following cases:
• When digits are being sent (BT is heard.)
 When a PS user attempts to hand over while connected to an operator (Attendant Console). BT is
heard.
 When user C sets Call Waiting to Terminal A while users...

NDA-24301 CHAPTER 1
Page 13
Revision 1.0
GENERAL DESCRIPTION
2. PBX functions are available in the Built-in PCS System.
Ta b l e s  1-3 through 1-11 show functions available in the Built-in PCS System. Some of the functions not
available in this system are:
D
term function
OAI-ACD functions
Data functions