NEC Neax 2400 Ipx System Operations And Maintenance Manual

NDA-24307 CHAPTER 8
Page 623
Issue 1
DCBD: Display of Call Block Entry Data
DCBD:Display of Call Block Entry Data
1. Functional Outline
This command is used to display the following Call Block data, assigned to a station:
Number of station/trunk whose call is to be blocked (in the remainder of this page, denoted as “Restriction
Number”)
Registered “Restriction Numbers” in total
These data can be obtained by entering any of the station’s Telephone Number (TYPE 1), Physical Station
Number (TYPE 2) or...

CHAPTER 8 NDA-24307
Page 624
Issue 1
DCBD: Display of Call Block Entry Data
Display Data
CNT: Registered “Restriction Numbers” in total (1-5)
DC: Each “Restriction Number”
When Physical Station Number is registered – Max.6 digits
When Telephone Number is registered – Max.16 digits
When Trunk Call Number is registered – Max.32 digits 

NDA-24307 CHAPTER 8
Page 625
Issue 1
DCEN: Display of Connection Trunk LENS Data for LDM
DCEN:Display of Connection Trunk LENS Data for LDM
1. Functional Outline
This command is used to display the registered connection trunk/route data by designating LENS.
2. Parameters
Input data
C_LENS: Line Equipment Number [6 digits]
Display data
C_RT: Connection Route Number [1-1023]
C_TK: Connection Trunk Number [1-4095]
RT: External Route Number
TK: Trunk Number [1-255]
TN: Tenant Number 

CHAPTER 8 NDA-24307
Page 626
Issue 1
DCON: Display of Connection Status
DCON:Display of Connection Status
1. Functional Outline
This command displays the connection status of the station and trunks. If the specified station or trunk is busy,
the connected party is displayed.
2. Parameters
Input data
TYPE: Kind of Connection Status (1-4)
1=Station of Connection Status
2=Trunk of Connection Status
3=LENS of Connection Status
4=Connection Trunk of Connection Status (Fusion Network)
TN:
Note 1
STN: Maximum...

NDA-24307 CHAPTER 8
Page 627
Issue 1
DFTD: Display of System Message Details
DFTD:Display of System Message Details
1. Functional Outline
This command is necessary to print the system messages detected by the Fault Diagnostic programs.
When the fault scanning (Scanning PBX) is effective, the MAT can scan the PBX status by polling every 20
sec, (default setting is Effective.)
If the PBX has faults, this command executes automatically.
2. Parameters
Input data
New/Old
Show Details: YES/NO 

CHAPTER 8 NDA-24307
Page 628
Issue 1
DISS: Display of Program Issue
DISS:Display of Program Issue
1. Functional Outline
This command outputs to the printer and displays at the MAT, the program information (version, issue No. and
date) in the main memory, and the program information (SP No.and issue No.) in the port microprocessor
memory mounted in each circuit card in the PBX.
2. Parameters
Input data
Type of Issue: Main Memory/Port Microprocessor
Module Group:
Note 1
Unit:Note 1
Display data
Type: Main...

NDA-24307 CHAPTER 8
Page 629
Issue 1
DLEN: Display of LENS Data
DLEN:Display of LENS Data
1. Functional Outline
This command displays the data (station data or trunk data) assigned for a designated LEN. For Hotel system,
Room Class and Floor Service Data [Annex (ANX), Ground/Underground (G), Floor (FLR)] displays also.
2. Parameters
Input data
LENS
Display data
TN
STN: Maximum 6 digits
TEC: Telephone Equipment Number (1-31)
RSC: Route Restriction Class (0-15)
SFC: Service Feature Class (0-15)
ROOM CLASS:...

CHAPTER 8 NDA-24307
Page 630
Issue 1
DLEN: Display of LENS Data
TK
C_RT: Connection Route Number (1-1023)
C_TK: Connection Trunk Number (1-4095)
DATA MEANING DATA MEANING
901 Attendant Console 902 Originating Register Trunk
903 Incoming Register Trunk 904 MF Receiver
905 Sender Trunk DP/PB 906 PB Receiver for Automated Attendant Service
907AMP 908Not used
909 Three-Way Conference Trunk 910-912 Not used
913 Three-Way Conference Trunk for ATTCON 914 Not Used
915 Night Attendant Console 916 MFC Register
917...

NDA-24307 CHAPTER 8
Page 631
Issue 1
DLSL: Display of Lock Out Station - LENS
DLSL:Display of Lock Out Station - LENS
1. Functional Outline
This command prints the LENS of stations in lockout state.
2. Parameters
Input data
TYPE: Type of Printout (1-3)
1=Printout of all LEN in lockout
2=Printout of locked out LEN in the designated Module Group
3=Printout of locked out LEN in the designated Unit
MG:
Note 1, Note 2
UNIT:Note 2
Note 1:
The parameter is valid only when Type= 2.
Note 2:The parameter is valid...

CHAPTER 8 NDA-24307
Page 632
Issue 1
DLSS: Display of Lockout Station - Number
DLSS:Display of Lockout Station - Number
1. Functional Outline
This command prints the stations in lockout state by station number.
2. Parameters
Input data
TYPE: Type of Printout (1-3)
1=Printout of all lockout stations
2=Printout of lockout stations by tenant
3=Printout of lockout stations within a specified range of station number.
TN:
Note 1, Note 2
START STN: Maximum 6 digitsNote 2
END STN: Maximum 6 digitsNote 2
Note 1:...