NEC Neax 2400 Ipx System Operations And Maintenance Manual

NDA-24307 CHAPTER 8
Page 593
Issue 1
CHAPTER 8 MAINTENANCE COMMANDS
This chapter explains various commands used in the system administrative management procedure. Table 8-1
shows a list of maintenance commands.
Table 8-1  Command Lis t  
COMMAND COMMAND FULL NAME
ALLC Assignment of Line Load Control
ALMG Assignment of Alarm Grade Data
ATRF Assignment of Traffic Measurement Order
ATRFN Assignment of Traffic Measurement Order for Fusion Network
BOSD Back Up One-Touch Speed Call Memory Data
CADSD Continuous...

CHAPTER 8 NDA-24307
Page 594
Issue 1
MAINTENANCE COMMANDS
DLTEL Display of Telephone Number from LENS for LDM
DNTEL Display of Telephone Number from LENS for NDM
DPKG Display of Setting Port Package
DPSW Display Package Switch Status
DSTN Display of Station Data
DTELN Display of Telephone Number Data for NDM
DTF101 Display of Terminal Traffic Data
DTF102 Display of Route Traffic Data
DTF103 Display of Station Peg Count Data
DTF104 Display of Attendant Peg Count Data
DTF105 Display of Route Peg Count...

NDA-24307 CHAPTER 8
Page 595
Issue 1
MAINTENANCE COMMANDS
FLINST File Install
HDD_FDD Data Control Between HDD and FDD
HDD_MAT Data Control Between HDD and MAT
HDD_MAT_N Data Control Between HDD and MAT for NDM
HDFP HDD Format of PBX
MBCT Make Busy of Connection Trunk for LDM
MBLE Make Busy of LENS
MBPM Make Busy of Port Microprocessor
MBRT Make Busy of Route
MBSM Make Busy of System Message Printout
MBST Make Busy of Station
MBST_T Make Busy of Station - Telephone Number
MBTC Make Busy of...

CHAPTER 8 NDA-24307
Page 596
Issue 1
ALLC: Assignment of Line Load Control
ALLC:Assignment of Line Load Control
1. Functional Outline
This command designates the start and stop of line load control.
2. Parameters
Input Data
ALL/ONE: Operation Mode Selection (1,2)
O/A=Only One LP/All LPs
LP: Local Partition (LP) Number 
Note
STATUS: Line Load Control Status (0-3)
0=Stop Line Load Control
1=Start Line Load Control
2=Automatic Line Load Control is in effect (display only)
3=Status of all LPs do not match...

NDA-24307 CHAPTER 8
Page 597
Issue 1
ALMG: Assignment of Alarm Grade Data
ALMG:Assignment of Alarm Grade Data
1. Functional Outline
This command makes a flexible change of system message output grades. Thus, the PBX user can give a proper
alarm grade to each system message according to their requirements. When no data is assigned, the default
alarm grades are automatically adopted.
Note:This command cannot change the alarm grade for [6-A] system message.
2. Parameters
Input data
FK: Fault Message Kind...

CHAPTER 8 NDA-24307
Page 598
Issue 1
ATRF: Assignment of Traffic Measurement Order
AT R F :Assignment of Traffic Measurement Order
1. Functional Outline
This command is used to assign and delete node-level traffic measurement programs. A request for traffic
measurement is performed on each node basis when a traffic measurement instruction has been assigned by
this command. The collected traffic measurement data can be stored on the HD of the MAT, which can be
designated on the basis of traffic...

NDA-24307 CHAPTER 8
Page 599
Issue 1
ATRF: Assignment of Traffic Measurement Order
START C_RT: Start Connection Route Number (available when TYPE 18/19 is selected)
END C_RT: End Connection Route Number (available when TYPE 18/19 is selected)
Note:Assign the traffic measurement time period between START HOUR/MINUTE and END HOUR/
MINUTE longer than an hour. Also, if the measurement should be executed throughout a day, assign
the same data in both START HOUR/MINUTE and END HOUR/MINUTE parameter 

CHAPTER 8 NDA-24307
Page 600
Issue 1
ATRFN: Assignment of Traffic Measurement Order for Fusion Network
ATRFN:Assignment of Traffic Measurement Order for Fusion Network
1. Functional Outline
This command is used to assign and delete traffic measurement programs available on the Ethernet. A request
for traffic measurement is performed on a network basis when a traffic measurement instruction has been
assigned by this command. The collected traffic measurement data can be stored on the HD of the MAT...

NDA-24307 CHAPTER 8
Page 601
Issue 1
ATRFN: Assignment of Traffic Measurement Order for Fusion Network
END LGRT: End Logical Route Number (available when TYPE 2/5/8 is selected)
START C_RT: Start Connection Route Number (available when TYPE 18/19 is selected)
END C_RT: End Connection Route Number (available when TYPE 18/19 is selected)
Note 1:The selected traffic measurement data, except for TYPE 1 (Terminal Traffic), is collected with the
whole network systems as a single unit.
Note 2:When time...

CHAPTER 8 NDA-24307
Page 602
Issue 1
BOSD: Back Up One-Touch Speed Call Memory Data
BOSD:Back Up One-Touch Speed Call Memory Data
1. Functional Outline
Save Function
Saves the data residing in the One-Touch Speed Call Memory of ELC card onto a floppy disk.
Verify Function
Verifies the One-Touch Speed Call Memory data saved on the floppy disk with the data residing in the
One-Touch Speed Call Memory of ELC card.
Load Function
Loads the One-Touch Speed Call Memory data saved in the floppy disk into the...