NEC Neax 2400 Ipx System Operations And Maintenance Manual

NDA-24307 CHAPTER 8
Page 673
Issue 1
MBRT: Make Busy of Route
MBRT:Make Busy of Route
1. Functional Outline
This command assigns Idle/Busy status for all the trunks in the route designated.
2. Parameters
Input data
RT: Route Number of the external route/internal route. The Internal Route Number and its
meaning is shown in the table below.
MB: 0/1=Make Idle/Make Busy
DATA MEANING DATA MEANING
901 Attendant/Desk Console 902 Originating Register Trunk
903 Incoming Register Trunk 904 MF Receiver
905 Sender...

CHAPTER 8 NDA-24307
Page 674
Issue 1
MBSM: Make Busy of System Message Printout
MBSM:Make Busy of System Message Printout
1. Functional Outline
This command allows or inhibits the system message printer to output system messages.
2. Parameters
Input data
PORT NO.: Port Number of the printer
MB: 0/1=Make Idle/Busy 

NDA-24307 CHAPTER 8
Page 675
Issue 1
MBST: Make Busy of Station
MBST:Make Busy of Station
1. Functional Outline
This command assigns the Idle/Busy status of stations.
2. Parameters
Input data
TN
STN: Maximum 5 digits for Business system/maximum 6 digits for Hotel system.
MB: 0/1=Make Idle/Make Busy 

CHAPTER 8 NDA-24307
Page 676
Issue 1
MBST_T: Make Busy of Station - Telephone Number
MBST_T:Make Busy of Station - Telephone Number
1. Functional Outline
This command is used to assign the IDLE/BUSY status of stations, by using Telephone Numbers. This com-
mand is available at NCN (for Fusion network) only. 
Note 1
Note 1:
This command is available for PBX program software.
2. Parameters
Input Data
UGN: User Group Number
TELN: Telephone Number (max. 16 digits)
MB: Make Busy/Make Idle
Display Data
FPC:...

NDA-24307 CHAPTER 8
Page 677
Issue 1
MBTC: Make Busy of Trunk-Continuous
MBTC:Make Busy of Trunk-Continuous
1. Functional Description
This command is used to assign the IDLE/BUSY status of trunks. By using this command, plural trunks can
be placed into IDLE/BUSY state simultaneously per a route designated in “RT” parameter.
2. Parameters
RT: R o u t e  N u m b e r
TK: Trunk Number 
Note 1
MB: 0=Make Idle
1=Make Busy(Outgoing)
2=Make Busy (Bothway) 
Note 2
Note 1:
Plural trunks can be assigned...

CHAPTER 8 NDA-24307
Page 678
Issue 1
MBTK: Make Busy of Trunk
MBTK:Make Busy of Trunk
1. Functional Outline
This command assigns the Idle/Busy status of trunks.
2. Parameters
RT: R o u t e  N u m b e r
TK: Trunk Number
MB: 0=Make Idle
1=Make Busy (Outgoing) 

NDA-24307 CHAPTER 8
Page 679
Issue 1
MEM_HDD: Data Control Between Memory and HDD
MEM_HDD:Data Control Between Memory and HDD
1. Functional Outline
This command is used to save the following data from MEM of PBX to HDD of PBX, and vice versa.
2. Parameters
Input data
Direction Select: Memory to Hard Disk/Hard Disk to Memory/Verify HDD against MEM
Data Type Selection: Data Memory 
Note 1
Name Display
Wireless Call Forwarding
Call Forwarding
Speed Calling
User Assign Soft Key
Number Sharing 
Note 2
Call...

CHAPTER 8 NDA-24307
Page 680
Issue 1
MEM_HDD_N: Data Control Between Memory and HDD for NDM
MEM_HDD_N:Data Control Between Memory and HDD for NDM
1. Functional Outline
This command, available at the NCN only, is used to save/verify a series of Office Data from the Memory of
all Local Nodes to the HDD of the same node. 
2. Parameters
Input data
Direction Select: MEM to HDD/Verify HDD against MEM
Data Type Selection: Data Memory 
Note 1
Name Display
Wireless Call Forwarding
Call Forwarding
Speed Calling...

NDA-24307 CHAPTER 8
Page 681
Issue 1
MFCH: Make Busy of FCCH
MFCH:Make Busy of FCCH
1. Functional Outline
This command is used to set or reset the make busy state of the FCH card.
2. Parameters
Input data
FCHN: FCH Number [1-255]
MB: Make Busy Information [0/1]
0=Make Idle
1=Make Busy 

CHAPTER 8 NDA-24307
Page 682
Issue 1
PMBU: Port Microprocessor Back Up
PMBU:Port Microprocessor Back Up
1. Functional Outline
This command saves the contents of Port Microprocessor (PM) onto Floppy Disk (FD) or verifies them.
Information of firmware (Program Code) also appears on the screen.
2. Parameters
Input data
Direction Select: Port Microprocessor to MAT/Verify Port Microprocessor/Verify PM with Error
List Auto Verify Afterward can be performed when designating Port
Microprocessor to MAT.
PM...