NEC Neax 2400 Ipx System Operations And Maintenance Manual

NDA-24307 CHAPTER 8
Page 683
Issue 1
RALM: Release Alarm
RALM:Release Alarm
1. Functional Outline
This command clears the fault indications.
2. Parameters
Input data
WRT: Y/N=Alarm is released/Not released
RETURN TO MENU?: Y/N=Return to MENU/Start operation again
Display data
Alarms Released 

CHAPTER 8 NDA-24307
Page 684
Issue 1
RALMN: Release Alarm for NDM
RALMN:Release Alarm for NDM
1. Functional Outline
This command, available at the NCN only, clears the fault indications of all the nodes by clicking the release
button on the display. 
2. Parameters
Display data
FPC: FPC of alarm released nodes
Status: Result of releasing the alarm
OK/NG 

NDA-24307 CHAPTER 8
Page 685
Issue 1
RLST: Release Station/Trunk
RLST:Release Station/Trunk
1. Functional Outline
This command releases a station or trunk.
2. Parameters
Input data
TYPE: Type of Select (1-4)
1=Stations
2=Trunk
3=LENS
4=Connection Trunk
TN:
Note 1
STN: Maximum 6 digits Note 1
RT:Note 2
TK:Note 2
LENS:Note 3
Connection RT: (1-1023) Note 4
Connection TK: (1-4095) Note 4
Note 1:
This parameter is valid only when TYPE= 1.
Note 2:This parameter is valid only when TYPE= 2.
Note 3:This parameter...

CHAPTER 8 NDA-24307
Page 686
Issue 1
RLST_T: Release Station/Trunk - Telephone Number
RLST_T:Release Station/Trunk - Telephone Number
1. Functional Outline
This command is used to release a station/trunk, by using Telephone Numbers. This command is available at
NCN (for Fusion network) only. 
Note
Note:
This command is available for PBX program software.
2. Parameters
Input Data
TYPE: Telephone Number
Trunk
LENS
Connection Trunk
UGN: User Group Number 
Note 1
TELN: Telephone Number (max. 16 digits) Note...

NDA-24307 CHAPTER 8
Page 687
Issue 1
RLST_T: Release Station/Trunk - Telephone Number
Buttons
Get: Click to get information on the station/trunk
Release: Click to execute the station/trunk release.
Exit: Click to exit this command 

CHAPTER 8 NDA-24307
Page 688
Issue 1
SINZ: System Initialization
SINZ:System Initialization
1. Functional Outline
This command initializes the PBX from the MAT. At the time of system initialization, this command allows
the programs and the office data to be loaded from a Hard Disk of PBX into the RAM of PBX.
2. Parameters
Input data
TYPE: Kind of Initialization (1-4)
1=System Initialize
2=System Initialize Office Data Load & System Initialize
3=System Initialize Program Load & System Initialize
4=System...

NDA-24307 CHAPTER 8
Page 689
Issue 1
SINZI: System Initialization for ISW
SINZI:System Initialization for ISW
1. Functional Outline
This command is used to initialize ISW and all the LNs in IPX-U system from the MAT. Also, at the time of
system initialization, this command allows the programs and the office data to be loaded from a Hard Disk of
PBX into the RAM of PBX. To use this command, the MAT must be connected to ISW.
2. Parameters
Input data
TYPE SELECT: Kind of Initialization(1-4)
1=Non Load...

CHAPTER 8 NDA-24307
Page 690
Issue 1
SPTS: Scanning of Port Status
SPTS:Scanning of Port Status
1. Functional Outline
This command displays momentarily the working status of Port Microprocessor (PM) on Module Group (MG),
Unit and Group basis.
2. Parameters
Input data
MG
Unit
Group
Interval:  The unit for this parameter is second
Display data
PKG TYPE: (0-255)
PKG Status: 1/2=On Line/Make Busy
SP No.: Program information (1-3999)
ISSUE: Firmware Issue (0-4)
LEVEL STATUS
DATA MEANING DATA MEANING DATA...

NDA-24307 CHAPTER 8
Page 691
Issue 1
SPTS: Scanning of Port Status
PORT STATUS: when TYPE= “1”
0=circuit card is not mounted or Make Busy
1=More than one port in a group is Idle
2=All port in a group is busy
3=All port in a group is Hard Make Busy or Soft Make Busy
4=
when TYPE= “2”/“3”
0=Not assigned
1=Line Idle
2=Line Busy
3=Make Busy
4=Lockout
PORT DATA
KIND: Type of Port (1,2)
1/2=Station/Trunk
TN:
Note 1
STN: Maximum 6 digits Note 1
TEC: Telephone Equipment Number (1-31) Note 1 

CHAPTER 8 NDA-24307
Page 692
Issue 1
SPTS: Scanning of Port Status
RT:Note 2
TK:Note 2
TCL: Trunk Class (1-31) Note 2
RT: R o u t e  N u m b e r
DATA MEANING DATA MEANING
1 DP (10pps) 2 PB
3 DP/PB 4 DP (20pps)
5-11 Not used 12 D
term
13 Data Terminal via Dterm14 Hot Line
15 CAS Line 16 Data Terminal via Data Module
17 Not used 18 Virtual Line Appearance (for D
term 
Multi-Line)
19-20 Not used 21 ACD (MIS)
22 Not used 23 ISDN Terminal
24-26 Not used 27 Eight Conference Equipment
28-31 Not used
DATA...