NEC Neax 2400 Ipx System Operations And Maintenance Manual

NDA-24307 CHAPTER 8
Page 663
Issue 1
DTF601N: Display of Connection Route Peg Count Data for Fusion Network
DTF601N:Display of Connection Route Peg Count Data for Fusion Network
1. Functional Outline
This command displays the result of traffic measurement data for Type=18 (Connection Route Peg Count)
assigned by the ATRFN command.
2. Parameters
Traffic Data 1: Terminal Traffic-DTF101N
Route Traffic-DTF102N
Station Peg Count-DTF103N
Attendant Peg Count-DTF104N
Route Peg Count-DTF105N
Traffic Data 2:...

CHAPTER 8 NDA-24307
Page 664
Issue 1
DTF602N: Display of Connection Route Traffic Data for Fusion Network
DTF602N:Display of Connection Route Traffic Data for Fusion Network
1. Functional Outline
This command displays the result of traffic measurement data for Type=19 (Connection Route Traffic)
assigned by the ATRFN command.
2. Parameters
Traffic Data 1: Terminal Traffic-DTF101N
Route Traffic-DTF102N
Station Peg Count-DTF103N
Attendant Peg Count-DTF104N
Route Peg Count-DTF105N
Traffic Data 2: Service Peg...

NDA-24307 CHAPTER 8
Page 665
Issue 1
FLINST: File Install
FLINST:File Install
1. Functional Outline
This command is used to install the DPSW-dedicated database files to your MAT. This command is necessary
to provide each circuit card’s various information (such as circuit card name, equipped switch names, etc.)
when your system uses the DPSW/DPKG command.
2. Parameters
Input data
None
Buttons
Copy: Click to start the data file install.
Exit: Click to exit this command.

(1) Start up the FLINST command...

CHAPTER 8 NDA-24307
Page 666
Issue 1
HDD_FDD: Data Control Between HDD and FDD
HDD_FDD:Data Control Between HDD and FDD
1. Functional Outline
This command is used to install the program data from FDD of PBX to HDD of PBX, and to verify the program
data between FDD of PBX and HDD of PBX.
2. Parameters
Input data
System Select:  HFD 0/HFD 1
Direction Select:  Floppy Disk to Hard Disk/Verify HDD against FDD/Hard Disk to Floppy Disk
Data Type Selection: Data Memory
Note 1
Name Display
Wireless Call...

NDA-24307 CHAPTER 8
Page 667
Issue 1
HDD_MAT: Data Control Between HDD and MAT
HDD_MAT:Data Control Between HDD and MAT
1. Functional Outline
This command is used to save the following data from HDD of PBX to MAT.
2. Parameters
Input data
Direction Select: PBX Hard Disk to MAT/MAT to PBX Hard Disk/Verify HDD against MAT
Data Type Selection: Data Memory
Note 1
Name display
Wireless Call Forwarding
Program data
Note 2
Call Forwarding
Speed Calling
User Assign Soft Key
Number Sharing
Note 3
Call Block 
ACD...

CHAPTER 8 NDA-24307
Page 668
Issue 1
HDD_MAT_N: Data Control Between HDD and MAT for NDM
HDD_MAT_N:Data Control Between HDD and MAT for NDM
1. Functional Outline
This command, available at the NCN only, installs (overwrites) the updated Program data from the centralized
MAT onto the HDD of all local nodes. To use this command, first install the updated program data on the HDD
of the MAT and then execute the program installing onto the HDD of each LN.
2. Parameters
Input data
Data Type Selection:  Select...

NDA-24307 CHAPTER 8
Page 669
Issue 1
HDFP: HDD Format of PBX
HDFP:HDD Format of PBX
1. Functional Outline
This command is used to execute the formatting of the HDD of PBX.
2. Parameters
Input data (Selection by check)
0 System: HDD of No.0 System
1 System: HDD of No.1 System
Buttons
Execute: Click to execute the formatting.
Close: Click to exit this command. 

CHAPTER 8 NDA-24307
Page 670
Issue 1
MBCT: Make Busy of Connection Trunk for LDM
MBCT:Make Busy of Connection Trunk for LDM
1. Functional Outline
This command is used to set/reset the make busy state of the connection trunk.
2. Parameters
Input data
C_RT: Connection Route Number [1-1023]
C_TK: Trunk Number [1-4095]
MB: Make Busy Information [0/1]
0=Make Idle
1=Make Busy (Outgoing) 

NDA-24307 CHAPTER 8
Page 671
Issue 1
MBLE: Make Busy of LENS
MBLE:Make Busy of LENS
1. Functional Outline
This command assigns the Idle/Busy status of Line Equipment Numbers (LENS).
2. Parameters
Input data
LENS
MB: 0/1=Make Idle/Make Busy 

CHAPTER 8 NDA-24307
Page 672
Issue 1
MBPM: Make Busy of Port Microprocessor
MBPM:Make Busy of Port Microprocessor
1. Functional Outline
This command sets or resets the make-busy state of the circuit card that contains the port microprocessor. This
setting and resetting is performed individually for each circuit card. If the location of the circuit card containing
the port microprocessor is specified in this command, the operating state of all circuit cards mounted in the
associated unit is displayed.
2....