NEC Neax 2400 Ipx Isdn Feature Programming Manual

							NDA-24305 CHAPTER 4
Page 23
Revision 1.0
COMMANDS CONCERNING ISDN DATA ASSIGNMENT
IRL (CDN15)  Clear call when DTI alarm is detected.
0 = –
1  = Clear call when DTI alarm is detectedNote 2
Note 2:This data should be set when there is no Dch in the physical DTI.
MTC (CDN16)  Assignment of Timer T309 Value. Restoration timer (TC×MTC) sec.
0-15 = TC (CDN18) × MTC (Restart timer value)
TC (CDN17) Timer T309 Counter Value
0 =  – 4 = 30sec.
1 = 64 msec.5 =  5 min.
2= –6 =  1 sec.
3= 2 sec.7 =  –
DVRST (CDN20)  Call restriction while Tie Line is backed up on ISDN.
0 = No Restriction
1 = Speech call restriction (Speech. 3.1 kHz audio, 7 kHz audio calls are restricted.)
2 = Data call restriction (Unrestricted digital, restricted digital and Video data are
restricted.)
3 = Both Speech and Data calls are restricted.
RSCT  (CDN21)  Call restriction by Temporary Route InformationNote 3
0 = No Restriction
1 = Restriction
Note 3:This data is effective when TMPRT = 1.
ROCG (CDN22)  Outgoing Call Account by Temporary Route Information Note 4
0 = –
1 = Effective
Note 4:This data is effective when TMPRT = 1.
RICG (CDN23)  Incoming Call Account by Temporary Route InformationNote 5
0/1 = Out of Service/In Service
Note 5:This data is effective when TMPRT = 1.
STSENQ (CDN24) Status Inquiry Message Send Note 6
0/1 = Out of Service/In Service
Note 6:This data is not effective in Australia.
RETMSG (CDN30) Return Message for Connect ISDN LINE with Analog Trunk
0 = CALL PROC. + ALERT
1  = CALL PROC. + ALERT or CALL PROC. + PROGRESS 
						

							CHAPTER 4 NDA-24305
Pag e 2 4
Revision 1.0
COMMANDS CONCERNING ISDN DATA ASSIGNMENT
ANI (CDN31)  Timing to demand ANI Information
0  = There is no ANI demand at Incoming call
1 = After receiving 1st digit
2 = After receiving 2nd digit
3 = After receiving 3rd digit
4 = After receiving 4th digit
5 = After receiving 5th digit
6 = After receiving 6th digit
7 = After receiving 7th digit
SRV (CDN32) Additional Service SelectionNote 7
Bit0: Advice of Charge (AOC)
0 = Valid
1 = Invalid
Bit1: Malicious Call Trace (MCT)/Malicious Call Identification (MCID)
0 = Valid
1 = Invalid
Bit2-Bit6:  –
Bit7: For TON (CDN28) and/or NPI (CDN29)
0 = Invalid
1 = Valid
Note 7:Input this data by a decimal.
TON (CDN33) Type of Number  Note 8
0 = Unknown
1 = International Number
2 = National Number
3 = Network Special Number
4 = Subscriber Number
5=–
6 = Abbreviated Number
7 = Reserved for Extension
Note 8:This data is effective when ARTD CDN65 (INT) = 4 and SRV (CDN27) bit7 = 1.
NPI (CDN34) Numbering Plan Identification  Note 9
0 = Unknown
1 = ISDN/Telephony Numbering Plan
2=–
3 = Data Numbering Plan
4 = Telex Numbering Plan
5-7 = –
8 = National Standard Numbering Plan
9 = Private Numbering Plan
10-14  =–
15 = Reserved for Extension
Others =–
Note 9:This data is effective when ARTD CDN65 (INT) = 4 and ARTI SRV (CDN27) bit7 = 1. 
						

							NDA-24305 CHAPTER 4
Page 25
Revision 1.0
COMMANDS CONCERNING ISDN DATA ASSIGNMENT
L/T (CDN35) Local/Toll  Note 10 
0 = Local
1=Toll
Note 10:Only for Russia
ECCIS (CDN36) Event Based CCIS (E-CCIS) for the public ISDN Line
0/1 = Out of Service/In Service
ECCISTM (CDN37)  Release timer for E-CCIS Line
0 = 3 minutes (Default setting)
1 = 15 seconds
2 = 30 seconds
3 = 1 minute
4 = 2 minutes
5 = 5 minutes
6 = 10 minutes
7 = 15 minutes
8 = 30 minutes
9 = 1 hour
10-13 = Not used
14 = Immediately after call completion
15 = Not released
ECCISOB (CDN38) OG Billing for E-CCIS Line
0/1 = Out of Service/In Service
ECCISIB (CDN39) IC Billing for E-CCIS Line
0/1 = Out of Service/In Service
SPMET  (CDN40) Meter Pulse Observation Control
0=–
1 = Low to High Transition
2 = High to Low Transition
3 = Low to High & High to Low Transition
ECCISTD (CDN42)  Addressing Information used in E-CCIS
0 = Called DID Number
1 = Called Sub Address
MFCG2 (CDN43)  Calling Party Category
0 = Subscriber with Priority
1 = Subscriber without Priority
OPCC (CDN44) Optimal Call Control
0/1 = In Service/Out of Service
INTD (CDN47)  Interface Detail  Note 11
0=Q-SIG
1 = IS-11572 
						

							CHAPTER 4 NDA-24305
Pag e 2 6
Revision 1.0
COMMANDS CONCERNING ISDN DATA ASSIGNMENT
JECCIS (CDN48) Common Use with E-CCIS RT  Note 11
0/1 = Out of Service/In Service
ECCIS2 (CDN49) E-CCIS System  Note 11
0 = Fixed Channel System
1 = Common Channel System
2=Not used
3=Not used
Note 11:Valid since Series 7300 Release 4.
CTCF (CDN52) SS-CT/SS-CF Service  Note 12
0/1 = Out of Service/In Service
Note 12:Valid since Series 7400 Release 8.
RERT (CDN53) Rerouting function (used in conjunction with SS-CT/SS-CF service)  Note 13
Note 13:Valid since Series 7400 Release 8.
For the other CDNs in trunk application data, zero (0) should always be entered. 
						

							NDA-24305 CHAPTER 5
Page 27
Revision 1.0
CHAPTER 5 GATEWAY SERVICE
This chapter explains data assignment for ISDN gateway service. Refer to ISDN Features and Specifications for
availability of each Gateway Service on the Fusion Network.
Table 5-1  Gateway Service List (1/4)
SERVICE
FEATURE
CODESERVICE FEATURE NAME REMARKS
A-76Alternate Routing-PRI
A-88Automatic Call Distribution-PRI
A-92Announcement Service-PRI
A-94Automatic Circuit Assurance-PRI
A-96Automatic Trunk Test-PRI
B-19Boss-Secretary Transfer-PRI
B-22Boss-Secretary Override-PRI
C-95Call Forwarding-All Calls-PRI
C-95DCall Forwarding-All Calls-D
term-PRI
C-96Call Forwarding-Busy Line-PRI
C-97Call Pickup-Group-PRI
C-97DCall Pickup-Group-D
term-PRI
C-98Call Transfer-Attendant-PRI
C-99Call Transfer-All Calls-PRI
C-99DCall Transfer-All Calls-D
term-PRI
C-100Consultation Hold-All Calls-PRI
C-100DConsultation Hold-All Calls-D
term-PRI
C-101Call Forwarding-Intercept/Announcement-PRI
C-102Call Pickup-Direct-PRI
C-114Call Waiting-Terminating-PRI
C-119Call Park-PRI
C-123Call Forwarding-All Calls-Announcement-PRI
C-125Call Forwarding-Intercept-PRI
C-129Call Forwarding-Don’t Answer-PRI
D-115Distinctive Ringing-PRI 
						

							CHAPTER 5 NDA-24305
Pag e 2 8
Revision 1.0
GATEWAY SERVICE
D-116DDo Not Disturb-Dterm-PRI
D-117Data Line Security-PRI
D-118Data Privacy on Demand-PRI
D-119Data Interface-Automatic Answer-PRI
D-120Data Transparency-PRI
D-121Data Communications-PRI
D-122Data Uniform Numbering Plan-PRI
D-137Direct-In Termination (DIT)-PRI
E-14DElapsed Time Display-D
term-PRI
F-21Flexible Numbering of Stations-PRI
F-26Faulty Trunk Report-PRI
H-14DHands-Free Answer Back-D
term-PRI
H-15Hot Line-Outside-PRI
I-24Incoming Call Identification-PRI
I-25Incoming ISDN Call to Tie Line Connection-PRI
I-26Indialing Through Main-PRI
I-27Inter-PBX Coordinated Station Numbering Plan-PRI
I-28ISDN Individual Calling Line Identification (ICLID)
I-36Inter-Office Off-Hook Queuing-PRI
L-31Least Cost Routing-3/6-Digit-PRI
L-32LCR-Time of Day Routing-PRI
L-33LCR-Attendant Manual Override-PRI
L-34LCR-Automatic Overflow to DDD-PRI
L-35LCR-Clocked Manual Override-PRI
L-42Last Number Call-PRI
L-42DLast Number Called-D
term-PRI
L-44LDN Night Connection-PRI
Table 5-1  Gateway Service List (2/4)
SERVICE
FEATURE
CODESERVICE FEATURE NAME REMARKS 
						

							NDA-24305 CHAPTER 5
Page 29
Revision 1.0
GATEWAY SERVICE
L-46LDN Night Connection-Outside-PRI
L-49LCR-Special Line Warning Tone-PRI
M-71Miscellaneous Trunk Access-PRI
M-72Miscellaneous Trunk Restriction-PRI
M-73Music On Hold-PRI
M-74Modem Pooling-PRI
M-75Multiple Call Forwarding-All Calls-PRI
N-20Night Connection-Fixed-PRI
N-21Night Connection-Flexible-PRI
N-22Non-Delay Operation-PRI
N-29Night Connection Outside-System-PRI
N-31Nailed Down Connection-PRI
O-24Outgoing Trunk Queuing-PRI
O-26Outgoing Trunk Queuing-Deluxe-PRI
O-28Off-Hook Queuing-PRI
O-30Outgoing Trunk Queuing-Attendant-PRI
O-32Overflow-UCD-PRI
P-37Peg Count-PRI
P-38Primary Call Restriction-PRI
P-39PRI Trunk to Tie Line Connection with Pad Control
P-47Paging Transfer-PRI
P-49PRI Failsafe Routing
R-35Restriction from Outgoing Calls-PRI
S-82Speed Calling-System-PRI
S-82DSpeed Calling-System-D
term-PRI
S-83Station Message Detail Recording System-RS232C-PRI
Table 5-1  Gateway Service List (3/4)
SERVICE
FEATURE
CODESERVICE FEATURE NAME REMARKS 
						

							CHAPTER 5 NDA-24305
Pag e 3 0
Revision 1.0
GATEWAY SERVICE
S-84Speed Calling-Station-PRI
S-85Speed Calling-Group-PRI
S-86Simultaneous Voice and Data Transmission-PRI
S-87Synchronous Data Switching-PRI
S-88SMDR for Data Call-RS232C-PRI
S-89Speed Calling Override-System-PRI
S-107Station Individual Trunk Access-PRI
T- 3 7Tandem Switching of Tie Trunk-2/4-Wire-PRI
T- 3 8Three-Way Calling-PRI
T-38DThree-Way Calling-D
term-PRI
T- 4 0Toll Denial/Toll Diversion-PRI
T- 4 1Toll Restriction-3/6-Digit-PRI
U-6Uniform Call Distribution (UCD) -PRI
Table 5-1  Gateway Service List (4/4)
SERVICE
FEATURE
CODESERVICE FEATURE NAME REMARKS 
						

							NDA-24305 CHAPTER 5
Page 31
Revision 1.0
ALTERNATE ROUTING-PRI
A-76 ALTERNATE ROUTING-PRI
1. General Description
This feature is provided with LCR which automatically routes ISDN outgoing on-net calls over alternate
facilities when the first-choice trunk group is busy. The user selects the first-choice route by dialing the
corresponding access code, and the equipment then routes the call through alternate trunk groups only if the first
is busy. The PBX will also add or delete digits, when necessary, to complete the call to the desired station.
2. Operating Procedure
No manual operation is required.
3. Programming
STEP 1: Assign “ISDN Line Access Code” data referring to Chapter 3, “Basic Data Assignment for ISDN”
and the data for the alternate trunk access.
Note:STEP 7: AOPR - Assign ISDN Bch route number and the alternate route number to 
the OPR
STEP 8: ARSC - Assign RSC that allows Route Restriction Indexes (RRIs) for ISDN Bch
trunk route, the dummy route and the alternate trunk route.
STEP 2: Assign “ISDN Trunk” data referring to Chapter 3, Section 2, “ISDN Trunk Data Assignment” and
the data for the alternate trunk. 
						

							CHAPTER 5 NDA-24305
Pag e 3 2
Revision 1.0
AUTOMATIC CALL DISTRIBUTION-PRI
A-88 AUTOMATIC CALL DISTRIBUTION-PRI
1. General Description
This feature allows Automatic Call Distribution (ACD) features to be activated for incoming calls from ISDN
trunks.
Table 5-1  ACD Features
CODE NO. FEATURE NAME AVAILABILITY
A-31 Abandoned Call Search ×
A-34 Assistance-ACD Agent×
A-35 Automatic Answer×
A-37 Availability-ACD Position×
A-80 Announcements×
B-21 Break Mode Not Applicable
C-35 Call Distribution to Agents×
C-67 Call Transfer to Split Queue×
C-68 Call Waiting Indication-LCD Display/CW Lamp×
C-70 Calling Party Identification ×
C-108 Call Control Vector Not Applicable
C-127 Call Forwarding-Split×
E-6 Emergency/Recorder×
F-10 Function Groups (Splits) Not Applicable
F-25 Flexible ID Codes Not Applicable
H-20 Holidays Scheduling Not Applicable
L-19 Logon/Logoff Not Applicable
M-28 Monitoring-ACD Supervisor×
M-29 Multiple Customer Groups (ACD Groups) Not Applicable
M-79 Multiple Supervisor Groups (Splits) Not Applicable
N-12 Night Service-ACD×
N-14 Non-ACD Call Not Applicable