NEC Neax 2400 Ipx Isdn Feature Programming Manual
Have a look at the manual NEC Neax 2400 Ipx Isdn Feature Programming Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1168 NEC manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
NDA-24305 CHAPTER 6 Page 213 Revision 1.0 NATIONAL - ISDN2 - PRI N-42 NATIONAL - ISDN2 - PRI 1. General Description This feature allows the system to connect with N-ISDN2 network. NON-FACILITY ASSOCIATED SIGNALING and D-CHANNEL BACKUP are also available. Note 1:Network-side services, VIRTUAL TIE LINE, and B-ISDN services are not available. Note 2:The following issues of firmwares are required. 2. Operating Procedure No manual operation is required. 3. Programming STEP 1: ARTD - Assign the following CDN data for the N-ISDN2 route. CDN65 (INT): 1( N-ISDN2) STEP 2: ACBC - Assign Call by Call data for each OPR. NET: 2(N-ISDN2) SERV: 1 (SERVICE) CODE: Facility Coding Value 1: INWATS 2: OUTWATS 3: FX 4: Tie Trunk CIRCUIT CARD FIRMWARE ISSUE PA-24PRTB-A SP-3029 24PRT PROG-B 9 or later PA-24DTR SP-3010 24DTI PROG-A 6 or later PRT National ISDN2
CHAPTER 6 NDA-24305 Pag e 2 14 Revision 1.0 VIRTUAL TIE LINE V-18 VIRTUAL TIE LINE 1. General Description This service feature provides the virtual tie line service by setting up a connection between a PBX and another via ISDN network during the designated period of time. While the virtual tie line is set, one of the B-channels on the setup connection is used as a CCIS No. 7 signal channel and other B-channels as CCIS No. 7 voice channels. PBX PRTISDN B-ch B-ch B-ch D-ch CCH PBX PRT CCH Vir tual Tie Line (6B x n) D-ch
NDA-24305 CHAPTER 6 Page 215 Revision 1.0 VIRTUAL TIE LINE Service Status Note:When a call is connected to the Virtual Tie Line at the time designated to cancel the connection, the connection is extended by 10 minutes (maximum 30 minutes) to wait for the call to be released. After 30 minutes, the calls connected to the line will be released forcefully. PBXPBX PRT PRT ISDN Vir tual Tie Line is set at 8:30AM (for example) PBXPBX PRT Bxn Bxn PRT PBXPBX PRT PRT Virtual Tie Line is cancelled at 5:20PM (for example)Note ISDN ISDN
CHAPTER 6 NDA-24305 Pag e 2 16 Revision 1.0 VIRTUAL TIE LINE Setup/Cancel Protocol for Virtual Tie Line 2. Operating Procedure No manual operation is required. PBX Setup SE T UP ( B ) C ALL P RO C PBX ISDN C ON N AC K I A I CL F CO NN AC M D ISC R EL C OMP RE LDI S C R E L C OMP RE L S E TU P ( B) C ON N AC K CO NN A ND RL G Talk/Communicate Cancel Virtual Tie Line (CCIS No.7)
NDA-24305 CHAPTER 6 Page 217 Revision 1.0 VIRTUAL TIE LINE 3. Programming STEP 1: Assign the Basic Data for ISDN. (Refer to Chapter 3.) Note 1:If in Virtual Tie Line network, an alternative route cannot be assigned. Note 2:Example for ports allocation of the command ATRK. STEP 2: Assign the data for CCIS No. 7. STEP 3: Assign the Virtual Tie Line data. For the originating office: AVTL- Assign a schedule for Virtual Tie Line implementation period. TL/SPC (T/S): Time Link/Semi Permanent Connection DATE: Start day-End day Note 1 PTN: Pattern number (0-15) IC/OG: OG RT: Route No. used for Virtual Tie Line TK: First trunk No. of Virtual Tie Line route. D-LENS: LENS of DCH used for setting Virtual Tie Line CH: Number of Bch used for Virtual Tie Lin e Note 1 CALLING: The number of ISDN line of the self office KEY PAD: CALLED: The Virtual Tie Line number of ISDN line of the facing (terminating) office SUB: 0 WEEK: Week range Note 1 TIME: Start Time and End TimeNote 1 LV 7 B c h - 8 D c h LV 6 B c h - 7 SIG-ch LV 5 B c h - 6Speech LV 4 B c h - 5Speech LV 3 B c h - 4Speech LV 2 B c h - 3Speech LV 1 B c h - 2Speech LV0 Bch-1 Bch-17 LV 7 B c h - 1 6 LV 6 B c h - 1 5 LV 5 B c h - 1 4 LV 4 B c h - 1 3 LV 3 B c h - 1 2 LV 2 B c h - 1 1 LV 1 B c h - 1 0 LV0 DCH Bch-9 CCISOdd Even24PRT
CHAPTER 6 NDA-24305 Pag e 2 18 Revision 1.0 VIRTUAL TIE LINE For the terminating office:AVTL - Assign a schedule for Virtual Tie Line implementation period. TL/SPC (T/S): Time Link/Semi Permanent Connection DATE: Start day-End da y Note 1 PTN: Pattern number IC/OG: IC RT: Route No. used for Virtual Tie Line TK: First trunk No. of Virtual Tie Line route. D-LENS: LENS of DCH CH: Number of Bch used for Virtual Tie Lin e Note 1 CALLING: The number of ISDN line of the facing (originating) office SUB: 0 WEEK: Week range Note 1 TIME: Start Time and End TimeNote 1 AVTC - Assign a Virtual Tie Line Call data TN: STN: Note 2 Note 1: Data of DATE, WEEK, TIME and CH must match between the originating office and the terminating office. Note 2:In addition, “DID-Addressing” data is necessary for both Bch of ISDN and Speech CH of CCIS No. 7. ARTD-CDN66 (DC) ACDD-Assign a data for digits conversion to Virtual Tie Line number as follows; Virtual Tie Line No. 2255Bch RT=10 Speech RT=20 ISDN DID No. 234-1111 D/N=D RT=10 DC=1111, CDC=2255 A/D=0, XFR=0 D/N=D RT=20 DC=1111, CDC=2255 A/D=0, XFR=0
NDA-24305 CHAPTER 6 Page 219 Revision 1.0 EVENT BASED CCIS - ISDN TRANSPORT E-23 EVENT BASED CCIS - ISDN TRANSPORT 1. General Description This feature provides VIRTUAL TIE LINE for each event such as call origination and MCI message transmission. Inter-PBX link for this feature is established on B-channels of the public ISDN line using CCIS No. 7 signaling protocol. For addressing a specific terminal, Called Sub Address or Called DID Number is used depending on the network configuration. 2. Operating Procedure None. 3. Service Conditions 1. The ISDN Primary Rate Interface (PRI) trunk is used for this feature. 2. The following ISDN interfaces are available: 4 ESS DMS 100 N-ISDN2 3. When using Called Sub Address as addressing information: (a) channel negotiation and Sub Address-Addressing must be available in the public ISDN network. (b) different DID Numbers must be assigned to the ISDN line, the E-CCIS line and its alternate route. For the E-CCIS line, DID Number is required for each D-channel. (c) Sub Address assigned to the E-CCIS trunk must be common to both offices. 4. When using Called DID Number as addressing information: (a) a different DID Number is required for each channel of the E-CCIS line. (b) when channel negotiation is not available, call termination to an E-CCIS trunk must not be allowed except when DID Number assigned to the trunk is dialed. (c) different DID Numbers must be assigned to the ISDN line and the E-CCIS line. For the E-CCIS line, DID Number is required for each D-channel. (d) alternate route for the E-CCIS line cannot be assigned. 5. Each trunk for the E-CCIS line cannot be used for the public ISDN line. 6. Each channel used for a E-CCIS line must be controlled by a single D-channel (i.e. Each channel must be assigned to a single ISDN line). 7. Billing information on the E-CCIS line does not include Access Code or Converted Number.
CHAPTER 6 NDA-24305 Pag e 2 20 Revision 1.0 EVENT BASED CCIS - ISDN TRANSPORT 8. The following features are available for the E-CCIS line: Asynchronous Data Switching [A-44] Note Attendant Camp-On with Tone Indication – CCIS [A-45] Attendant-Controlled Conference – CCIS [A-46] Automatic Recall – CCIS [A-71] Automatic Number Identification (ANI) – CCIS [A-87] Busy Verification – CCIS [B-9] Brokerage Hotline – CCIS [B-10] Call Back – CCIS [C-44] Call Forwarding – All Calls – CCIS [C-45] Call Forwarding – Busy Line – CCIS [C-46] Call Forwarding – Don’t Answer – CCIS [C-47] Call Forwarding – Intercept – CCIS [C-48] Call Forwarding – Override – CCIS [C-49] Call Transfer – All Calls – CCIS [C-50] Called Station Status Display – CCIS [C-51] Calling/Called Number Display – CCIS [C-52] Call Processing Indication – CCIS [C-53] Call Transfer – Attendant – CCIS [C-54] Consultation Hold – All Calls – CCIS [C-58] Call Forwarding Assignment – Attendant – CCIS [C-94] Data Communication – CCIS [D-41] Note Data Interface – Automatic Answer – CCIS [D-65] Note Data Line Security – CCIS [D-66] Note Data Line Privacy – CCIS [D-67] Note Data Privacy on Demand – CCIS [D-68] Note Data Transparency – CCIS [D-69] Note Deluxe Traveling Class Mark – CCIS [D-70] Dial Access to Attendant – CCIS [D-71] Digital Display – Station – CCIS [D-72] Digital Display – Trunk – CCIS [D-73] Direct-In Termination – CCIS [D-74] Distinctive Ringing – CCIS [D-75] Do Not Disturb – D term – CCIS [D-76D] Data Hotline – CCIS [D-86] Note Dialed Number Display – Recall – CCIS [D-91] Dual Hold D term – CCIS [D-93D] Executive Right-of-Way – CCIS [E-8] Elapsed Time Display – CCIS [E-9] E-911 ANI Unified Number of Digits – CCIS [E-20] Flexible Numbering of Stations – CCIS [F-12] Hands-Free Answerback – D term – CCIS [H-10D] House Phone – CCIS [H-11]
NDA-24305 CHAPTER 6 Page 221 Revision 1.0 EVENT BASED CCIS - ISDN TRANSPORT Hotline – CCIS [H-12] Incoming Call Identification – CCIS [I-16] Individual Attendant Access – CCIS [I-17] Inter-Position Transfer – CCIS [I-18] Individual Trunk Access – CCIS [I-19] Look Ahead Routing – CCIS [L-25] LDN Night Connection – CCIS [L-29] Message Reminder – CCIS [M-34] Message Reminder – D term – CCIS [M-34D] Message Waiting Lamp Setting – Attendant – CCIS [M-35] Message Waiting Lamp Setting – Station – CCIS [M-36] Miscellaneous Trunk Access – CCIS [M-37] Miscellaneous Trunk Restriction – CCIS [M-38] Modem Pooling – CCIS [M-39] Note Multiple Call Forwarding – All Calls – CCIS [M-40] Multiple Call Forwarding – Busy Line – CCIS [M-41] Multiple Call Forwarding – Don’t Answer – CCIS [M-42] Multiple Console Operation – CCIS [M-43] Message Center Interface – CCIS [M-67] Night Connection – Fixed – CCIS [N-15] Night Connection – Flexible – CCIS [N-16] Name Display – System – CCIS [N-37] Off-Hook Queuing – CCIS [O-11] Outgoing Trunk Queuing – CCIS [O-12] Paging Access – CCIS [P-28] Restriction from Outgoing Calls – CCIS [R-22] Serial Call – CCIS [S-52] Service Display – D term – CCIS [S-53D] Simultaneous Voice and Data Transmission – CCIS [S-54] Single-Digit Station Calling – CCIS [S-55] Station Controlled Conference – CCIS [S-56] Station-to-Station Calling – CCIS [S-57] Station-to-Station Calling – Operator Assistance – CCIS [S-58] Step Call – CCIS [S-59] Synchronous Data Switching – CCIS [S-60] Supervisory Call – CCIS [S-73] Toll Restriction – 3/6-Digit – CCIS [T-26] Trunk Answer from Any Station – CCIS [T-27] Uniform Numbering Plan – CCIS [U-5] Voice Call – CCIS [V-7] Note:When A/D=1(Digital) is assigned by CDN45. ARTD, this feature is available.
CHAPTER 6 NDA-24305 Pag e 2 22 Revision 1.0 EVENT BASED CCIS - ISDN TRANSPORT 9. The following features are available only when the signal-channel link of the E-CCIS line is established: Centralized Billing-CCIS [C-55] Centralized System Management Report – CCIS [C-57] 10. When a RELEASE COMPLETE message (Cause number 34 [No circuit/channel available] /44 [Requested circuit/channel not available]) or DISCONNECT message is received from an ISDN network, route advance is executed according to the parameter RA (Order of Route Advancing) of AOPR command. Route advance is available when a calling party is under the following status. Station without a held station/trunk Station with a held station Station with a held trunk Tandem Connection Attendant Console without a held station/trunk Attendant Console with a held station Attendant Console with a held trunk However, route advance is not available in the following cases: Call origination from an ISDN terminal Tandem connection from an MFC trunk Data communication When route advance is executed, the following services are not available: OFF-HOOK QUEUING [O-7] OUTGOING TRUNK QUEUING [O-2] INTER-OFFICE OFF – HOOK QUEUING [I-11] OUTGOING TRUNK BUSY ANNOUNCEMENT [O-21] ROUTE RESTRICTION – ANNOUNCEMENT [R-27] Dialing AUTHORIZATION CODE [A-21] from an ISDN trunk 4. Programming STEP 1: Assign the Basic Data for ISDN. (Refer to Chapter 3.)