NEC Neax 2400 Ipx Isdn Feature Programming Manual

							NDA-24305 CHAPTER 5
Page 43
Revision 1.0
CALL FORWARDING-ALL CALLS-Dterm-PRI
To cancel CALL FORWARDING-ALL CALLS-Dterm-PRI from My-line:
1. Lift the handset or press the “SPEAKER” key; receive Dial Tone.
2. Press the CALL FORWARDING-ALL CALLS-D
term-PRI feature key; receive Service Set Tone.
The LED of the associated feature key will go out. The LCD displays:
3. Replace the handset or press the “SPEAKER” key.
To set CALL FORWARDING-ALL CALLS-D
term-PRI for multi-line appearance other than the My-line:
1. Lift the handset or press the “SPEAKER” key.
2. Press the multi-line appearance; receive Dial Tone. Then press CALL FORWARDING-ALL CALLS-D
term-
PRI feature key; receive Special Dial Tone.
3. Dial the desired target station number; receive Service Set Tone. The LED of the associated feature key does
not light at the station setting the service. If the multi-line appearance is another D
term’s My-line, that
station’s feature key LED will light. The setting station’s LCD displays:
4. Replace the handset or press the “SPEAKER” key.
5. If the target station is the Attendant, the LCD displays:
To monitor CALL FORWARDING-ALL CALLS-D
term-PRI for a multi-line appearance other than the My-
line:
1. Press the multi-line appearance. Then press the CALL FORWARDING-ALL CALLS-D
term-PRI feature
key. The LCD displays:
FWD CNCL
(Time Display)FORWARD CANCEL
(Time Display)
[Dterm Series III] [Dterm Series E]
FWD SET XXXX
(Time Display)
TA R G E T
STATION
FORWARD SET XXXX
(Time Display)
TA R G E T
STATION
[Dterm Series III] [Dterm Series E]
FWD SET OPR
(Time Display)FORWARD SET OPR
(Time Display)
[Dterm Series III] [Dterm Series E]
FWD SET XXXX
(Time Display)
TA R G E T
STATION
FORWARD SET XXXX
(Time Display)
TA R G E T
STATION
[Dterm Series III] [Dterm Series E] 
						

							CHAPTER 5 NDA-24305
Pag e 4 4
Revision 1.0
CALL FORWARDING-ALL CALLS-Dterm-PRI
To cancel CALL FORWARDING-ALL CALLS-Dterm-PRI for a multi-line appearance other than the My-line:
1. Lift the handset or press the “SPEAKER” key; receive Dial Tone.
2. Press the multi-line appearance; receive Dial Tone. Then press the CALL FORWARDING-ALL CALLS-
D
term-PRI feature key; receive Service Set Tone. The LCD displays:
The associated LED that is lit at another station goes out.
3. Replace the handset or press the “SPEAKER” key.
3. Programming
Refer to [C-5] CALL FORWARDING-ALL CALLS”.
FWD CNCL
(Time Display)
[Dterm Series III] [Dterm Series E]
FORWARD CANCEL
(Time Display) 
						

							NDA-24305 CHAPTER 5
Page 45
Revision 1.0
CALL FORWARDING-BUSY LINE-PRI
C-96 CALL FORWARDING-BUSY LINE-PRI
1. General Description
This feature permits a call to a busy station to be immediately forwarded to a predesignated station or to the
ATTENDANT CONSOLE [A-3].
If a called station is in a hunt  group and forwards calls to another hunt group,  it  can be determined by system
data, whether the calling party is directed to the called parties hunt group or the terminating parties hunt group
when all of the forwarded stations are busy.
2. Operating Procedure
To set CALL FORWARDING-BUSY LINE-PRI from an Individual Station:
1. Lift the handset; receive Dial Tone.
2. Dial the specific CALL FORWARDING-BUSY LINE-PRI access code; receive Special Dial Tone.
3. Dial the desired target station number; receive Service Set Tone.
To cancel CALL FORWARDING-BUSY LINE-PRI from an Individual Station:
1. Lift the handset, receive Dial Tone.
2. Dial the specific CALL FORWARDING-BUSY LINE-PRI cancel code; receive Service Set Tone.
To set CALL FORWARDING-BUSY LINE-PRI from the ATTENDANT CONSOLE [A-3]:
1. Press an idle “LOOP” key.
2. Dial the specific CALL FORWARDING-BUSY LINE-PRI access code; receive Special Dial Tone.
3. Dial the TENANT SERVICE [T-12] number (2 digits).
4. Dial the originating station number.
5. Dial the desired target station number; receive Service Set Tone.
To cancel CALL FORWARDING-BUSY LINE-PRI from the ATTENDANT CONSOLE [A-3]:
1. Press an idle “LOOP” key.
2. Dial the specific CALL FORWARDING-BUSY LINE-PRI cancel code.
3. Dial the TENANT SERVICE [T-12] number (2 digits).
4. Dial the originating station number; receive Service Set Tone.
3. Programming
STEP 1: ASYD - System Data 1, Index 5, bit 0: Access codes for CALL FORWARDING-BUSY LINE
and CALL FORWARDING-DON’T ANSWER are same 
or separate? 0/1: Same/Separate.
bit 5: Hunting Group when transferred party is busy (Station 
Hunting after C.F.-Busy Line) 0/1: Hunt in Transferring 
Party’s Group/Hunt in Transferred Party’s Group
bit 7: Multiple Call Forwarding Service 0/1: Out/In Service
STEP 2: ANPD - Reserve a number level for feature access and cancel. Assign Connection Index, CI=N;
Normal. Assign NND in accordance with a predetermined numbering plan. 
						

							CHAPTER 5 NDA-24305
Pag e 4 6
Revision 1.0
CALL FORWARDING-BUSY LINE-PRI
STEP 3: ASPA - Assign an access code to CALL FORWARDING-BUSY LINE Entry, SID=10 and to
CALL FORWARDING-BUSY LINE Cancel, SID=11. Assign Connection Status Index
(CI) for Normal service.
STEP 4: ASFC - Assign the stations to receive CALL FORWARDING-BUSY LINE a Service Feature
Class that allows SFI=9.
STEP 5: AKYD - For D
term sets, CALL FORWARDING-BUSY LINE may be assigned to a programmable
line/feature key. Assign KYI=1 and FKY=1.
STEP 6: ATNR - Allow tenant-to-tenant connection for Inter- and Intra-tenant connections. Assign Tenant
Restriction Index (TRI)=1. For this feature to be set by the Attendant Console assignment,
assign TRI=3 for Inter- and Intra-tenant connection via the Attendant Console. This allows
a station in one tenant to be Call Forwarded to a station in the same or different tenant. Also
assign TRI=0, station-to-station calling.
STEP 7: ACFO - For tenant-wide CALL FORWARDING-BUSY LINE of an incoming DID and DIT calls,
Assign CF=1 for a destination (CFI) of either the Attendant Console or a station. 
Note:Step 7 is necessary for CALL FORWARDING on a system basis only.
Note 
						

							NDA-24305 CHAPTER 5
Page 47
Revision 1.0
CALL PICKUP-GROUP-PRI
C-97 CALL PICKUP-GROUP-PRI
1. General Description
This feature permits a station user to answer ISDN Network calls directed to other lines in a preset CALL
PICKUP-GROUP simply by dialing a pickup code.
2. Operating Procedure
Picking up an incoming ISDN call:
1. A call from the ISDN network terminates to a trunk.
2. Stations within the same CALL PICKUP-GROUP-PRI ring.
3. Lifts the handset; receives Dial Tone.
4. Dials the call pickup code; the call is connected to the station.
Picking up an incoming call (Consultation Hold):
1. A call from the ISDN network terminates to a trunk.
2. The station within the same CALL PICKUP-GROUP-PRI ring.
3. The station flashes the switchhook; receives special Dial Tone.
4. Dials the call pickup code; the call is connected to the station.
5. The first party is put on CALL HOLD [C-6] status.
3. Programming
STEP 1: ANPD - Reserve a number level for feature access and cancel. Assign Connection Index, CI=N, H;
Normal, Hooking. Assign NND in accordance with a predetermined numbering plan. 
STEP 2: ASPA - Assign an access code for the CALL PICKUP GROUP, SID = 7 for Connection Status
Index (CI) of Normal and Hooking.
STEP 3: ACPG - Assign members of CALL PICKUP GROUP. If two stations are ringing simultaneously,
the station that was programmed first will be picked up first.
Note:Maximum 100 stations per group.
 No limit to the number of Groups per system.
 Stations must belong to the same tenant. 
						

							CHAPTER 5 NDA-24305
Pag e 4 8
Revision 1.0
CALL PICKUP-GROUP-Dterm-PRI
C-9 7D   CALL  PIC KU P-G RO UP-Dte rm-P RI
1. General Description  This feature permits a station user to answer an ISDN network call directed to another line in a preset CALL
PICKUP-GROUP by using a programmable line/feature key.
CALL PICKUP-GROUP-D
term-PRI may be used by seizing Dial Tone from any multi-line appearance on the
Dterm.
2. Operating Procedure Picking up an incoming call:
1. An incoming call from the ISDN network terminates to a trunk.
2. The stations within the same call pickup group ring.
3. Lifts the handset; receives Dial Tone.
4. Press the call pickup group feature key; the call is connected to the station. The LCD displays:
Picking up an incoming call (consultation Hold):
1. An incoming call from the ISDN network terminates to a trunk.
2. The stations within the same call pickup group ring.
3. Press the “TRANSFER”/“CALL HOLD” feature key; receives Special Dial Tone.
4. Press the call pickup group feature key; the call is connected to the station.
5. The first party is put on CALL HOLD [C-6] status.
3. Programming STEP 1 ~ STEP 3: Refer to  [C-97] “CALL PICKUP-GROUP-PRI”  in this manual.
STEP 4: AKYD - Optional. Assign a programmable Line/Feature key as a CALL PICKUP key. Assign KYI = 1 and FKY = 12.
PCK XXXX
(Time Display)
CALLING
STATION/TRUNK
XXXX
CALLED STATION[Dterm Series III]
PICK UP XXXX
(Time Display)
CALLING
STATION/TRUNK
XXXX
CALLED STATION[Dterm Series E] 
						

							NDA-24305 CHAPTER 5
Page 49
Revision 1.0
CALL TRANSFER-ATTENDANT-PRI
C-98 CALL TRANSFER-ATTENDANT-PRI
1. General Description 
This feature permits a station user, while connected to an ISDN network call, to signal the Attendant and have
the Attendant transfer the call to another station within the system.
2. Operating Procedure
Calling the Attendant:
1. While engaged in a PRI trunk call, press the switchhook; receive Special Dial Tone.
2. Dial the operator/access code.
3. a. ATTENDANT CONSOLE [A-3] “RCL” lamp flashes and buzzer sounds.
b. The station receives Ringback Tone.
Answering by the Attendant:
1. Refer to “ATTENDANT CONSOLE USER’S GUIDE”.
If the station wishes to return to the Central Office trunk call while the Attendant is being called:
1. Press the switchhook; the “RCL” lamp goes out; the buzzer stops.
2. Ringback Tone stops; the station returns to PRI trunk call.
3. Programming
STEP  1: ASYD - System  Data  2,  Index  1,  bit  0  and  1: Assign a data to allow CONSULTATION HOLD. All 
types of connections.
STEP 2: ATNR - Allow tenant restriction. Assign Tenant Restriction Index (TRI) 0, and 4 on an intra-and
Inter-tenant basis. 
						

							CHAPTER 5 NDA-24305
Pag e 5 0
Revision 1.0
CALL TRANSFER-ALL CALLS-PRI
C-99 CALL TRANSFER-ALL CALLS-PRI
1. General Description 
This feature permits a station user to transfer incoming or outgoing ISDN calls to another station within the
system without Attendant assistance.
2. Operating Procedure
To transfer a call in progress:
1. While connected with the first party; press the switchhook; receive Special Dial Tone.
2. Dial the third party; receive Ringback Tone.
3. At this point, the station user can either:
(a) Hang up before the third party answers. The first and third parties will be connected when third party
answers.
(a) Wait for third party answer and announce the transfer while keeping the first party in a CONSULTA-
TION HOLD-ALL CALLS-PRI [C-100] condition. When the station user hangs up, the first and third
parties will be automatically connected.
3. Programming
STEP 1: ASYD - System Data 1, Index 69, bit 0: Return transferred call to transferring party after the
elapse of the Recall Timer. Only applicable to blind 
transfers. 
bit  2: Short tone on recall of CALL TRANSFER-ALL CALLS. 
Ringback Tone is briefly heard by the person answering
the recall. 
 Index 140: (if ASFC SFI 103 = 0)/Index 247 (if ASFC SFI 103 = 1). 
Assign the Recall Timer for a station-to-station CALL 
TRANSFER-ALL CALLS. For 30 seconds, assign data 
00H. (TC3 = 2 sec, TC7 = 8 sec.) RAM data 3FH for 30 
seconds. 
System Data 2, Index 1, bits 0 & 1:Assign a data to allow CONSULTATION HOLD [C-17, 
C-17D]. 
STEP 2: ATNR - Allow tenant-to-tenant connection for Intra- and Inter-tenant connections. Assign Tenant
Restriction Index (TRI) 0 and 4 on an Intra- and Inter-tenant basis.
STEP 3: ARSC - The station receiving the call must be assigned a Route Restriction Class (RSC) that will
allow the station to be connected to the trunk if a trunk is involved. 
						

							NDA-24305 CHAPTER 5
Page 51
Revision 1.0
CALL TRANSFER-ALL CALLS-Dterm-PRI
C-99D CALL TRANSFER-ALL CALLS-Dterm-PRI
1. General Description 
This feature permits a station user to transfer incoming or outgoing ISDN calls without Attendant assistance.
2. Operating Procedure
To transfer a call in progress:
1. While connected with the first party, press the “TRANSFER” key; receive Special Dial Tone.
2. Dial the third party; receive Ringback Tone.
3. At this point, the station user can either wait and announce the call or hang up before the transfer is
completed. The LCD display for an announced transfer will be:
The LCD display for an unannounced transfer will be:
3. Programming
Refer to [C-99] “CALL TRANSFER-ALL CALLS-PRI” in this manual.
XFR XXXX
(Time Display)
TRANSFERRED
PA R T Y
TRANSFER XXXX
(Time Display)
TRANSFERRED
PA R T Y[Dterm Series III] [Dterm Series E]
XFR XXXX
(Time Display)
TRANSFERRED
PA R T Y
XXXX
TRANSFERRING
PA R T Y
TRANSFER XXXX
(Time Display)
TRANSFERRED
PA R T Y
XXXX
TRANSFERRING
PA R T Y
[Dterm Series III] [Dterm Series E] 
						

							CHAPTER 5 NDA-24305
Pag e 5 2
Revision 1.0
CONSULTATION HOLD-ALL CALLS-PRI
C-100 CONSULTATION HOLD-ALL CALLS-PRI
1. General Description 
This feature permits a station user to hold any incoming or outgoing  ISDN network call or any intraoffice call
while originating a call to another station within the system.
2. Operating Procedure
To hold the original call and place the second call:
1. Press the switchhook; receive Special Dial Tone.
2. The original call is held.
3. Dial the second station number; receive Ringback Tone.
4. The second station answers; the consultation hold state has been entered.
To return to the original call:
1. In any of the following cases, the calling station can return to the original call by pressing the switchhook:
(a) The Second station called for consultation is busy.
(b) The Calling station cannot access to second station due to restriction or any other reason.
(c) Second station does not answer.
2. If the second party hangs up, the calling station will automatically be returned to the original call.
If the originating station flashes the switchhook, THREE-WAY CALLING [T-2] will be initiated.
3. Programming
STEP 1: ASYD - System Data 2, Index 1,bits 0 & 1: CONSULTATION  HOLD  allowed  or  denied?  00:
Denied; 01: Originating and Terminating Calls allowed,
Tandem Call Denied; 11: All calls allowed. Normally
assign data “11”. 
System Data 3, Index 2, bits 0-3: Switchhook flash starts timer. To calculate this value: 
(1-FH) × 120 msec = Timer. 
bits  4-7: Switchhook flash ends timer. To calculate this value: (1-
FH) × 120 msec = Timer. For both beginning and
ending timers, assign 91H for 120-1080 msec.
f (t) bit 0-3 bit 4-7
0ms
120ms
No detectionSHF detect
1080ms Disconnection