NEC Neax 2400 Ipx Isdn Feature Programming Manual

							NDA-24305 CHAPTER 6
Page 223
Revision 1.0
EVENT BASED CCIS - ISDN TRANSPORT
Note:
Example of ports allocation by ATRK command is shown below.
STEP 2: Assign CCIS No. 7 related data.
STEP 3: ARTD - Assign Bearer Capability for the speech channels of the E-CCIS line.
CDN:45 A/D: 0/1 =  Analog (Bearer Capability: Speech)/
Digital (Bearer Capability: Unrestricted Digital)
Note that Bearer Capability for the signal channel is Unrestricted Digital only.
Assign Trunk Selection Sequence.
CDN:49 TRKS: 0/1= Select the trunk (CIC No.) in ascending order/descending order,
which assigned by the ACSC command.
Note that each office must be assigned a different value to avoid collision at the time of
call origination.
LV 7
LV 6
LV 5
LV 4
LV 3
LV 2
LV 1
LV 0
LV 7
LV 6
LV 5
LV 4
LV 3
LV 2
LV 1
LV 0 Odd
EvenBch-8
Bch-7
Bch-6
Bch-5
Bch-4
Bch-3
Bch-2
Bch-1
DCHDch
Signal
Speech
Speech
Speech
Speech
Speech
Bch-17
Bch-16
Bch-15
Bch-14
Bch-13
Bch-12
Bch-11
Bch-10
Bch-9CCIS
24PRT 
						

							CHAPTER 6 NDA-24305
Pag e 2 24
Revision 1.0
EVENT BASED CCIS -  ISDN TRANSPORT
Assign Dialed Number confirmation for the E-CCIS (speech channel) RT and the E-CCIS (signal channel) RT.
CDN : 66 DC: Assign the same value as the ARTD command of CDN 66 (DC) which assigned for common
ISDN (speech channel RT)
STEP 4: ARTI - Assign the following CDN data for the E-CCIS route.
ECCIS (Event Based CCIS): 1
ECCISTM: Release Timer for the E-CCIS line
0: 3 minutes (Default)
1: 15 seconds
2: 30 seconds
3: 1 minute
4: 2 minutes
5: 5 minutes
6: 10 minutes
7: 15 minutes
8: 30 minutes
9: 1 hour
10-13: Not used
14:  Immediately after call completion (for Speech Channel)/
1 minute (for Signal Channel)
15: Not released
ECCISOB: OG Billing for E-CCIS Line
0: Not required
1: Required
ECCISIB: IC Billing for E-CCIS Line
0: Not required
1: Required
ECCISTD: Addressing information used in E-CCIS
0: Called DID Number
1: Called Sub Address 
						

							NDA-24305 CHAPTER 6
Page 225
Revision 1.0
EVENT BASED CCIS - ISDN TRANSPORT
STEP 5: AEVT -  Assign virtual tie line data for E-CCIS.
RT: Route Number
TK: Trunk Number
TYPE: System type (Dch is used commonly or separately with ISDN trunk)
DESTINATION: Destination Number (Maximum 6 digits)
CALLING: Calling Number (Maximum 24 digits)
CALLED: Called Number (Maximum 24 digit s)
Note
C_RT: CCIS Signal Route Number
C_TK: CCIS Signal Trunk Number
VRY: Verification of Connection 
Note
0: Not required
1: Required
OPR: Outgoing Route Selection Pattern Number of CBC Service
RA: Order of Route Advance of CBC Service
Note:When Verification of Connection is in service, if the last four digits of  the received number is not equal to
those of Called Number, the connection is not established.
STEP 6: AVTC -  Assign Virtual Tie Line Number for the E-CCIS route.
STEP 7: ACBC - If required, assign Call by Call data for the E-CCIS route. 
						

							CHAPTER 6 NDA-24305
Pag e 2 26
Revision 1.0
EVENT BASED CCIS -  ISDN TRANSPORT
Examples of Data Assignment for the E-CCIS line
 Example of port allocation when using Called Sub Address as addressing information Note
Data assignment procedure related to the E-CCIS line is shown below.
STEP 1: ARTD -  RT20 CDN 45 A/D: 0 (Voice information is transmitted)
CDN 49 TRKS: 0 (Select the trunk (CIC No.) in ascending order)
CDN 66 DC: 4
Note
RT120 CDN 66 DC: 4Note
Note:
The same value in “DC” assigned for ISDN B channel must be programmed to both E-CCIS Signal and
Speech route (RT10-CDN66 DC: 4).
STEP 2: ARTI -  RT20 ECCIS: 1 (E-CCIS Route)
ECCISTM: 5 (Release timer: 5 minutes)
ECCISOB:  1 (OG billing for the E-CCIS line is required)
ECCISIB: 1 (IC billing for the E-CCIS line is required)
ECCISTD: 1 (Addressing information: Sub Address)
RT120 ECCIS: 1 (E-CCIS Route)
ECCISTM : 3 (Release timer: 1 minute)
ECCISOB:  1 (OG billing for the E-CCIS line is required)
ECCISIB:  1 (IC billing for the E-CCIS line is required)
ECCISTD: 1 (Addressing information: Sub Address)
DID Number for incoming calls from an E-CCIS line: 0471-81-3500
DID Number for incoming calls from an alternate route: 0471-81-360024PRT
RT110 TK1 ISDN D-channel
RT120 TK1 E-CCIS Signal Channel Sub Address: 9803
RT20 TK3 E-CCIS Speech Channel Sub Address: 9802
RT20 TK2 E-CCIS Speech Channel Sub Address: 9801
RT20 TK1 E-CCIS Speech Channel Sub Address: 9800
RT10 TK19 ISDN B-channel
RT10 TK18 ISDN B-channel
RT10 TK17 ISDN B-channel
RT10 TK16 ISDN B-channel
RT10 TK2 ISDN B-channel
RT10 TK1 ISDN B-channel
......
......
......
...... 
						

							NDA-24305 CHAPTER 6
Page 227
Revision 1.0
EVENT BASED CCIS - ISDN TRANSPORT
STEP 3: AEVT - RT20 TK1 DESTINATION: 9800 (E-CCIS trunk identification number)
CALLING: 0471813500 (DID number for incoming call)
CALLED: 0891245600 (DID number for outgoing call)
C_RT: 120 (CCIS Signal Route Number)
C_TK: 1 (CCIS Signal Trunk Number)
VRY: 1 (Verification of Connection: Required)
TK2 DESTINATION: 9801 (E-CCIS trunk identification number)
CALLING: 0471813500 (DID number for incoming call)
CALLED: 0891245600 (DID number for outgoing call)
C_RT: 120 (CCIS Signal Route Number)
C_TK: 1 (CCIS Signal Trunk Number)
VRY: 1 (Verification of Connection: Required)
TK3 DESTINATION: 9802 (E-CCIS trunk identification number)
CALLING: 0471813500 (DID number for incoming call)
CALLED: 0891245600 (DID number for outgoing call)
C_RT: 120 (CCIS Signal Route Number)
C_TK: 1 (CCIS Signal Trunk Number)
VRY: 1 (Verification of Connection: Required)
RT120 TK1 DESTINATION: 9803 (E-CCIS trunk identification number)
CALLING: 0471813500 (DID number for incoming call)
CALLED: 0891245600 (DID number for outgoing call)
C_RT: 120 (CCIS Signal Route Number)
C_TK: 1 (CCIS Signal Trunk Number)
VRY: 1 (Verification of Connection: Required)
OPR: 20 (OPR number for RT20 specified in the ACBC command)
RA: 0 (RA number for RT20 specified in the ACBC command)
STEP 4: AVTC -  TN:1
STN: 3500 (DID Number or Converted Number generated by ACDD command) 
						

							CHAPTER 6 NDA-24305
Pag e 2 28
Revision 1.0
EVENT BASED CCIS -  ISDN TRANSPORT
The following data is assigned for route advance using Remote Access to System.
STEP 5: AOPR - TDPTN: 0
OPR: 15
RA: 1
E: 0
RT:  1 0
SKIP: 0
PNL: 30
OV F T:  1
PRSC: 0
STEP 6: AADC - PNL:30
DC: 0891246000*(Calling number for Remote Access to System plus*)
STEP 7: ASYD - System Data 1, Index 43, Bit 0:1 (Forced Account Code Dialing is not required for Remote
Access to System)
STEP 8: ARTD - For the alternate incoming route, assign CDN 38 (FA) as 1.
STEP 9: ARAC -  ICTN: 1
ACC: 3600 (DID Number or Converted Number generated by ACDD command)
TN: 1 
						

							NDA-24305 CHAPTER 6
Page 229
Revision 1.0
EVENT BASED CCIS - ISDN TRANSPORT
 Example of port allocation when using DID Number as addressing information
Data assignment procedure related to the E-CCIS line is shown below.
STEP 10: ARTD - RT20 CDN 45 (A/D):  0
CDN 66 (DC):  4
RT120 CDN 66 (DC):  4
STEP 11: ARTI -  RT20 CDN 31 (ECCIS): 1 (E-CCIS Route)
CDN 32 (ECCISTM) : 5 (Release timer: 5 minutes)
CDN 33 (ECCISOB) : 1 (OG billing for the E-CCIS line is required)
CDN 34 (ECCISIB) : 1 (IC billing for the E-CCIS line is required)
CDN 36 (ECCISTD) : 0 (Addressing information: Called DID Number)
RT120 CDN 31 (ECCIS): 1 (E-CCIS Route)
CDN 32 (ECCISTM) : 3 (Release timer: 1 minute)
CDN 33 (ECCISOB) : 1 (OG billing for the E-CCIS line is required)
CDN 34 (ECCISIB) :  1 (IC billing for the E-CCIS line is required)
CDN 36 (ECCISTD) : 0 (Addressing information: Called DID Number)
24PRT
RT110 TK1 ISDN D-channel
RT120 TK1 E-CCIS Signal Channel DID Numb e r:0471-81-3503
RT20 TK3 E-CCIS Speech Channel DID Numb e r:0471-81-3502
RT20 TK2 E-CCIS Speech Channel DID Numb e r:0471-81-3501
RT20 TK1 E-CCIS Speech Channel DID Numb e r:0471-81-3500
RT10 TK19 ISDN B-channel
RT10 TK18 ISDN B-channel
RT10 TK17 ISDN B-channel
RT10 TK16 ISDN B-channel
RT10 TK2 ISDN B-channel
RT10 TK1 ISDN B-channel
......
......
......
...... 
						

							CHAPTER 6 NDA-24305
Pag e 2 30
Revision 1.0
EVENT BASED CCIS -  ISDN TRANSPORT
STEP 12: AEVT  - RT20 TK1 DESTINATION: 3500 (E-CCIS trunk identification number)
CALLING: 0471813500 (DID number for incoming call)
CALLED: 0891245600 (DID number for outgoing call)
C_RT: 120 (CCIS Signal Route Number)
C_TK: 1 (CCIS Signal Trunk Number)
VRY: 1 (Verification of Connection: Required)
TK2 DESTINATION: 3501 (E-CCIS trunk identification number)
CALLING: 0471813501 (DID number for incoming call)
CALLED: 0891245601 (DID number for outgoing call)
C_RT: 120 (CCIS Signal Route Number)
C_TK: 1 (CCIS Signal Trunk Number)
VRY: 1 (Verification of Connection: Required)
TK3 DESTINATION: 3502 (E-CCIS trunk identification number)
CALLING: 0471813502 (DID number for incoming call)
CALLED: 0891245602 (DID number for outgoing call)
C_RT: 120 (CCIS Signal Route Number)
C_TK: 1 (CCIS Signal Trunk Number)
VRY: 1 (Verification of Connection: Required)
RT120 TK1 DESTINATION: 3503 (E-CCIS trunk identification number)
CALLING: 0471813503 (DID number for incoming call)
CALLED: 0891245603 (DID number for outgoing call)
C_RT: 120 (CCIS Signal Route Number)
C_TK: 1 (CCIS Signal Trunk Number)
VRY: 1 (Verification of Connection: Required)
OPR: 20 (OPR number for RT20 specified in the ACBC command)
RA: 0 (RA number for RT20 specified in the ACBC command)
STEP 13: AVTC - TN: 1
STN: 3500
STN: 3501 DID Number or Converted Number generated by ACDD command
STN: 3502
STN: 3503 
						

							NDA-24305 CHAPTER 6
Page 231
Revision 1.0
EVENT BASED CCIS - Q-SIG TRANSPORT
E-24 EVENT BASED CCIS - Q-SIG TRANSPORT
1. General Description
This feature provides VIRTUAL TIE LINE for each event such as call origination and MCI message
transmission. Inter-PBX link for this feature is established on B-channels of the private ISDN line using CCIS
No. 7 signaling protocol. For addressing a specific terminal, Called Sub Address or Called DID Number is used
depending on the network configuration.
2. Operating Procedure
None.
3. Service Conditions
1. The ISDN Primary Rate Interface (PRI) trunk is used for this feature.
2. ETS 300 172 or ISO/IEC 11572 is available as  ISDN interface for this service.
3. E-CCIS signal channel assignment is not necessary when activating via the private ISDN line because
E-CCIS line is controlled by D-channel of ISDN.
4. This feature is activated between two PBXs directly connected to each other. Therefore, this feature is not
available for the using tandem office.
5. Since this feature uses the B-channel for ISDN as the speech line, the speech line is not established when
all B-channels are busy.
6. When using Called Sub Address as addressing information:
(a) Sub Address-Addressing must be available in the ISDN network.
(b) different DID Numbers must be assigned to the ISDN line, the E-CCIS line.
For the E-CCIS line, DID Number is required for each D-channel.
(c) Sub Address assigned to the E-CCIS trunk must be common to both offices.
7. When using Called DID Number as addressing information:
(a) a different DID Number is required for each channel of the E-CCIS line. 
(b) when multiple routes are assigned for the terminating office, call termination to an E-CCIS trunk must
not be allowed except when DID Number assigned to the trunk is dialed.
(c) different DID Numbers must be assigned to the ISDN line and the E-CCIS line. For the E-CCIS line,
DID Number is required by for each D-channel.
8. Each channel used for a E-CCIS line must be controlled by a single D-channel (i.e. Each channel must be
assigned to a single ISDN line). 
						

							CHAPTER 6 NDA-24305
Pag e 2 32
Revision 1.0
EVENT BASED CCIS - Q-SIG TRANSPORT
9. Billing information 
(a) OG billing and IC billing data should be set for each route via the ARTI command.
(b) Trunk identification number assigned at DESTINATION of the AEVT command is output to the
SDMR text in place of a station number.
(c) Billing information on E-CCIS line does not include Access Code or Converted Number (ASYD-
SYS1 Index 32, bit 5/Index 34, bit 5/Index 62, bit 2=0).
10. Peg Count service for E-CCIS line (ETS 300 172 or ISO/IEC 11572) is activated for ISDN route setting
Virtual Tie Line data.
(Peg Count for ISDN line includes the route for E-CCIS line)
11. This service is established when no E-CCIS line is established or the call is originated even if the all
channels are busy.
12. The release timer is activated when the CCIS call is disconnected.
13. The following features are available for the E-CCIS line:
 Asynchronous Data Switching [A-44] 
Note 
 Attendant Camp-On with Tone Indication – CCIS [A-45]
 Attendant-Controlled Conference – CCIS [A-46]
 Automatic Recall – CCIS [A-71]
 Automatic Number Identification (ANI) – CCIS [A-87]
 Busy Verification – CCIS [B-9]
 Brokerage Hotline – CCIS [B-10]
 Call Back – CCIS [C-44]
 Call Forwarding – All Calls – CCIS [C-45]
 Call Forwarding – Busy Line – CCIS [C-46]
 Call Forwarding – Don’t Answer – CCIS [C-47]
 Call Forwarding – Intercept – CCIS [C-48]
 Call Forwarding – Override – CCIS [C-49]
 Call Transfer – All Calls – CCIS [C-50]
 Called Station Status Display – CCIS [C-51]
 Calling/Called Number Display – CCIS [C-52]
 Call Processing Indication – CCIS [C-53]
 Call Transfer – Attendant – CCIS [C-54]
 Consultation Hold – All Calls – CCIS [C-58]
 Call Forwarding Assignment – Attendant – CCIS [C-94]
 Deluxe Traveling Class Mark – CCIS [D-70]
 Data Communication – CCIS [D-41] 
Note 
 Data Interface – Automatic Answer – CCIS [D-65] Note 
 Data Line Security – CCIS [D-66] Note 
 Data Line Privacy – CCIS [D-67] Note 
 Data Privacy on Demand – CCIS [D-68] Note 
 Data Transparency – CCIS [D-69] Note 
 Dial Access to Attendant – CCIS [D-71]
 Digital Display – Station – CCIS [D-72]