NEC Neax 2400 Ipx Isdn Feature Programming Manual

							NDA-24305 CHAPTER 6
Page 293
Revision 1.0
Q-SIG (CIRCUIT SWITCHED BASIC CALL - ETSI VERSION)
Note 3:
Assign “1” when the number display on LCD of terminal is required.
Note 4:Assign “1” when the User-to-User Signaling notification is required.
Note 5:Assign “1” when the multi-rate bearer service is used.
STEP 4: ARTI - Assign the trunk application data for Bch and Dch as follows. 
INTD=0 (Q-SIG)
Note:This data is effective since release 4.
STEP 5: ATRK - Assign Bch trunk data. Note that Dch trunk data should be assigned after STEP 9: ACIC 2
command assignment.
STEP 6: ADPC - Assign PC (Point Code) for both Bch and Dch at each physical interface.
Note:Same PC (not existing PC for CCIS) must be assigned for both Bch and Dch. The Point Code does not
have any relationship to the other PBX’s like in CCIS
STEP 7: ACSC - Assign the location of DCH (Dch Handler).
(Refer to the following example)
STEP 8: ACIC 1 - Assign CSCG
PC=xxx CSCG=Even No. (130-254)
STEP 9: ACIC 2 - Assign CIC No.
PC=xxx CIC (1~999) LENS (for speech channel)
STEP 10: ATRK - Assign the LEN of Dch trunk.
Note:The following data is available if necessary.
ASFC - SFI 139 : SID to Network - Privacy [COLR] for Q-SIG.
0 = 
−
1 = SID to Network - Privacy
PIM0
Group 
No.05 07
04 06
CSCG=130 (Even No.) CICG No. = 0 CCH= 0004
1 0004
2 0004
3 0004
4 0004
5 0004
6 0004
7 0004PRT
Note:Bch location is not necessary. (DCH location only)
Attention: The circuit card must be initialized after changing data. 
						

							CHAPTER 6 NDA-24305
Pag e 2 94
Revision 1.0
ADVICE OF CHARGE (AOC) - RECEIPT AND DISPLAY OF AOC FROM A FOREIGN Q-SIG NETWORK
A-136 ADVICE OF CHARGE (AOC) - RECEIPT AND DISPLAY OF AOC FROM A FOREIGN Q-SIG 
NETWORK
1. General Description
This feature provides the calling station originated a call to ISDN network using Q-SIG/IS-11572 line with the
charge information display sent from the ISDN network. Whether the charge information is displayed or not can
be specified on a station basis.
2. Operating Procedure
No manual operation is required.
3. Service Conditions
1. This feature is available since Series 7400 (Release 8) software.
2. This service is available for the D
term and ISDN terminal. Attendant Console is not available for this service.
3. This feature is effective on condition that the call is originated to the ISDN network through ETS 300 172/
IS-11572 line.
4. This feature supports AOC-E only (not applied to AOC-D nor AOC-S).
AOC-S: Charging information at call set-up time
The billing rate is sent to the caller when originating a call.
Also, when the billing rate is changed during the communication, the new information is sent to
the caller.
AOC-E: Charging information at the end of the call
When the call is completed, the charge information is sent to the caller.
AOC-D: Charging information during the call
While the call is in progress, the charge information and the billing rate information are sent to
the caller.
5. This feature supports the total billing information only when the call is completed.
6. Maximum number of digits for the charge display is six digits. When the charge exceeds the maximum
digits, the LCD displays “*999,999”.
7. Charge information of more than ten digits can be displayed on the LCD (number of unit digit is not
displayed). The charge of unit digit is raised to ten digit and charge of decimal places is omitted.
8. This feature is activated only when the charge information is sent from the ISDN network. Therefore, the
call charge is not displayed when dialing the number free of charge. 
						

							NDA-24305 CHAPTER 6
Page 295
Revision 1.0
ADVICE OF CHARGE (AOC) - RECEIPT AND DISPLAY OF AOC FROM A FOREIGN Q-SIG NETWORK
4. Interactions
1. When Call Transfer - All Calls service/Blind Transfer Service is activated with this feature, the call charge
is not sent to the calling station. However, when Call Transfer - All Calls  is activated with this feature, the
call charge is sent to the forwarding station.
2. When Call Forwarding - Busy Line [C-2], Call Forwarding - All Calls [C-5] is activated with this feature,
the call charge is sent to the calling  station.
3. When Call Forwarding - Don’t Answer [C-5] is activated with this feature, the call charge is not sent.
4. When C.F. - PS Incoming Incomplete is activated with this feature, the call charge is not sent.
5. When Calling Name Identification Presentation (CNIP)/Connected Name Identification Presentation
(CONP) [C-153] is provided with this feature, the call charge is not sent. 
						

							CHAPTER 6 NDA-24305
Pag e 2 96
Revision 1.0
ADVICE OF CHARGE (AOC) - RECEIPT AND DISPLAY OF AOC FROM A FOREIGN Q-SIG NETWORK
5. Example of Message Sequence
Some examples of message sequence for this service are shown below.
Station A calls to Station B and the two stations are connected.
ETSI/ 
IS-11572ISDN 
network
Station B Station A
(1)
Message Sequence of charge information sent when the call is disconnected from a called user 
(2) Message Sequence of charge information sent when the call is disconnected from a calling user
Originating PINX
SETUP 
chargeRequest. invSETUP 
chargeRequest. inv
CALLPROC
ALERT 
chargeRequest. res
CONN
DISC 
aocFinal. invSETUP
CALLPROC
ALERT
CONN
DISC 
(charge information) CALLPROC
ALERT 
chargeRequest. res
CONN
DISC 
aocFinal. invMediate PINXOutput Gateway 
PINXISDN public 
Network
ISDN public 
Network
Originating PINX
SETUP 
chargeRequest. invSETUP 
chargeRequest. inv
CALLPROC
ALERT 
chargeRequest. res
CONN
DISC 
aocFinal. invSETUP
FA C  
getFinalcharge. invFA C  
getFinalcharge. invDISC CALLPROC
ALERT
CONN
REL 
(charge information) CALLPROC
ALERT 
chargeRequest. res
CONN
DISC 
aocFinal. invMediate PINXOutput Gateway 
PINX 
						

							NDA-24305 CHAPTER 6
Page 297
Revision 1.0
ADVICE OF CHARGE (AOC) - RECEIPT AND DISPLAY OF AOC FROM A FOREIGN Q-SIG NETWORK
6. Programming
STEP 1: Assign the data for establishing Q-SIG/IS-11572 line followed by “Q-SIG (CIRCUIT SWITCHED
BASIC CALL - ETSI VERSION)” or “IS-11572 (LAYER 3 SPECIFICATIONS FOR INTER-PBX
SIGNALING PROTOCOL)” in this chapter. Also, assign the data for “STATION MESSAGE
DETAIL RECORDING SYSTEM-RS232C-PRI” [S-83] in Chapter 5.
STEP 2: ASFC – Assign the service feature class to be allowed this service to each station.
SFI109 (Call charge notification to ISDN terminal), RES=1 (In service)
SFI175 (AOC), RES=1 (In service) 
						

							CHAPTER 6 NDA-24305
Pag e 2 98
Revision 1.0
This page is for your notes.