NEC Neax 2400 Imx Wireless System Manual

CHAPTER 4 ND-70290 (E)
Pag e 1 54
Revision 3.0
TTC Q.931A PROTOCOL TIE LINE WITH PCS ROAMING
4) ADPC (Destination Point Code Data)
- Assign Point Code for both Bch route and Dch route.
- The values for a Point Code is 1 through 16383. You can assign any number as the Point Code  
for them, however, do not duplicate the Point Code which is used for No. 7 CCIS.
5) ACSC (CSC Data)
- Assign Dch and Bch location for CSCG.
- The values for CSCG is 130 through 255.
- Even number CSCGs are used for Dch location...

ND-70290 (E) CHAPTER 4
Page 155
Revision 3.0
TTC Q.931A PROTOCOL TIE LINE WITH PCS ROAMING
2) Condition: 24DTI/30DTI is mounted in Slot 07 of PIM0 and 2DCH is mounted in Slot 05 of 
PIM0. ACSC data is as follows.
Note 1:The location of DCH (Dch Handler) must be assigned in parameter “CCH” of this
command.
Note 2:Above is an example when #0 DCH of PA-2DCH circuit card is used.
6) ACIC1 (CIC Code Data1)
- With respect to PC assigned in the ADPC command, assign CSCG of the Dch assigned in the 
ACSC...

CHAPTER 4 ND-70290 (E)
Pag e 1 56
Revision 3.0
TWO-LINE OPERATION
TWO-LINE OPERATION
1. GENERAL DESCRIPTION
This feature allows for the appearance of two lines on the line (L1 and L2) keys of the PS.
2. OPERATING PROCEDURE
No manual operation is required.
3. SERVICE CONDITIONS
1. This feature is available for Series 7300 or later software.
2. Two kinds of lines can appear on the PS: My Line and  Sub Line.  These lines are associated with the station
numbers assigned to the port on the interface circuit....

ND-70290 (E) CHAPTER 4
Page 157
Revision 3.0
TWO-LINE OPERATION
5. PROGRAMMING
1) APSD (Assignment of the PS Operation Data for DM)
This command assigns the PS operation data including its tenant No., station No., Service Feature 
Restriction Class (SFC) and the Route Restriction Class (RSC) in consideration of the numbering 
plan/restriction data. Assign My Line and Sub Line data of the PS.
 TN : Tenant
 PSTN : PS STN
 KIND : PS KIND : Assign 6 (D
term-PSII) for My Line.
Assign 7 (Dterm-PSII Sub...

CHAPTER 4 ND-70290 (E)
Pag e 1 58
Revision 3.0
VOICE MAIL INDICATION (VMI)
VOICE MAIL INDICATION (VMI)
1. GENERAL DESCRIPTION
This feature provides ON/OFF control of the Voice Mail Message (VMM) indication of the PS (including the
PS in a visitor node) via Message Center Interface (MCI). This feature is also available in the CCIS and
Netfusing networks.
There are two types of notification methods: active notification and passive notification.
Active notification:The notification is given when a voice...

ND-70290 (E) CHAPTER 4
Page 159
Revision 3.0
ZT PROGRAM DOWNLOAD
ZT PROGRAM DOWNLOAD
1. GENERAL DESCRIPTION
This feature allows maintenance personnel to update the ZT program by command operation. Accordingly, only
one ZT needs to be updated by the dedicated tool.
2. OPERATING PROCEDURE
1. Using the dedicated tool, write new program into a ZT. This ZT is called “Program Master ZT”.
2. Connect “Program Master ZT” to the system.
3. Download new program from “Program Master ZT” to the other ZTs, called...

CHAPTER 4 ND-70290 (E)
Pag e 1 60
Revision 3.0
ZT PROGRAM DOWNLOAD
4. PROGRAMMING
1) ACSDL (Assignment for CS/ZT Data for LDM)/ACSDN (Assignment for CS/ZT Data for NDM)
This command is used to assign the ZT related data including the PHS Community Number,
Calling Area No., Group No., ZT NO., ZT LENS, and ZT KIND.
When this data assignment is finished, 3B+D channels of the CSINT circuit card start up.
 PHS Community Number: 1-1024
 Calling Area Number: 1-32
 Group Number: 1-8
 ZT Number: 1-32
 TN:...

ND-70290 (E) CHAPTER 4
Page 161
Revision 3.0
CALL FORWARDING - DROPPED CALLS
CALL FORWARDING - DROPPED CALLS
1. GENERAL
This feature provides a call forwarding function when a PS encounters a Squelch Disconnection (such as PS
moving out of zone, failing to hand over a call, or a sudden power down of the PS) during a two-way connection
with a station/trunk. If this feature is set, the PS can forward the unexpectedly disconnected call to a pre-assigned
forwarding destination, such as a PS, a user of voice...

CHAPTER 4 ND-70290 (E)
Pag e 1 62
Revision 3.0
CALL FORWARDING - DROPPED CALLS
3. SERVICE CONDITIONS
1. This feature can be set at each PS, that is already provided with the C.F.-PS INCOMING INCOMPLETE
feature.
2. The forwarding destination of C.F.-PS INCOMING INCOMPLETE is also designated as the destination of
this feature.
3. This feature can be cancelled also by cancelling C.F.-PS INCOMING INCOMPLETE. However, if the
following is set, C.F.-PS INCOMING INCOMPLETE is cancelled, while this feature is...

ND-70290 (E) CHAPTER 4
Page 163
Revision 3.0
CALL FORWARDING - DROPPED CALLS
- After a certain period of no answer, the call is shifted to the destination of CALL FORWARDING - DON’T
ANSWER.
[When CALL FORWARDING - DON’T ANSWER is not assigned at the forwarded party]
- Recall to the Squelch PS is not made, and the forwarded party continues to ring. 
15. When a call is forwarded by this feature and also is shifted to another destination, the forwarding kind to be
notified to the destination is “C.F.-PS...