NEC Neax 2400 Imx Installation Manual

NDA-24234 CHAPTER 5
Page 331
Revision 3.0
INSTALLATION TEST PROCEDURE
If the TLT is a 4W E&M System, connect the related leads as shown below.
Set up a loop-back connection between the DTI Trunk to be tested and another DTI Trunk as shown below:
Figure 032-3  DTI Test Configuration
If the office is the primary office (Clock-Source-Office), perform the tests by disconnecting the PLO and the
M-OSC.  (The mode of the PLO becomes “Self Operation Mode.”)
NAP-200-032
Sheet 3/3
Outgoing Trunk (COT, TLT, DTI...

CHAPTER 5 NDA-24234
Pag e 33 2
Revision 3.0
INSTALLATION TEST PROCEDURE
Test Outline:
The purpose of this test is to confirm, by setting up an incoming trunk connection test for each incoming trunk, that
speech can be made with the ATTCON when a Ringdown Signal Interface is used, or with a station when a Dial-In
Signal Interface is used. This test also confirms that the call can be released. Incoming trunks must be tested one at
a time using the sequence of Route and Trunk Numbers assigned at each...

NDA-24234 CHAPTER 5
Page 333
Revision 3.0
INSTALLATION TEST PROCEDURE
NAP-200-033
Sheet 2/2
Incoming Trunk (COT, TLT, DTI Card)
Connection Test
For a Dial-In Signal 
Interface.Station “A” dials the access code for the outgoing trunk and 
the number of Station “B”.
Station “B” answers the call and confirms speech.
The call is released.
Make temporary cross connections for the next trunk to be 
tested.
Restore the temporary cross connections, temporary Office Data, etc. to the original.
A
ENDB 

CHAPTER 5 NDA-24234
Pag e 33 4
Revision 3.0
INSTALLATION TEST PROCEDURE
NAP-200-034
Sheet 1/1
Direct-In Termination Trunk (COT Card)
Connection Test
START
On the MDF, make temporary cross connections between the Trunk for Direct-In Termination (DIT) and 
an LC.
C.O.Line Incoming Call Station “B” dials the number of LC “C” (Station “C”).
Incoming Call to Station via 
DIT Trunk.The call terminates to Station “A”; Station “A” rings.
Confirm that the ringing is distinct from that of an intra-
office call or...

NDA-24234 CHAPTER 5
Page 335
Revision 3.0
INSTALLATION TEST PROCEDURE
NAP-200-035
Sheet 1/1
SND (RST Card) Connection Test
START
When a C.O. Line or Tie Line is 
not connected with the trunk, 
make an arrangement for trunk 
loop-back as illustrated above.On the MDF, make temporary cross connections for a 
loop back circuit.
Temporarily assign Office Data from the MAT so that a 
connection can be set up with Station “B” via a SND.
Make  busy  all  SNDs On the front of the RST circuit card, set all MBS...

CHAPTER 5 NDA-24234
Pag e 33 6
Revision 3.0
INSTALLATION TEST PROCEDURE
NAP-200-036
Sheet 1/1
3-party Conference Trunk Function Test
START
Made busy all CFTs Made busy all CFTs using MAT command “MBTK”.
Test CFTs one at a time Un-busy (make idle) only the CFT to be tested.
Stations “A” and “B” are engaged in a station to station 
connection.
Station “A” makes a Switch Hook Flash (SHF) and after hearing 
DT, dials the station number of Station “C”.
Station “C” answers the call.
Station “A”, after having...

NDA-24234 CHAPTER 5
Page 337
Revision 3.0
INSTALLATION TEST PROCEDURE
NAP-200-037
Sheet 1/1
Connection Test-Announcement Trunk for 
Announcement Service
START
Dial the announcement service 
codeStation “A” dials the announcement service code.
Check the contents of the 
announcementStation “A” is connected to the announcement machine 
and hears the announcement.
Dial the announcement service 
codeStation “B” dials the announcement service code.
Check the contents of the 
announcementStation “B” is...

CHAPTER 5 NDA-24234
Pag e 33 8
Revision 3.0
INSTALLATION TEST PROCEDURE
NAP-200-038
Sheet 1/1
Connection Test-Digital Announcement 
Trunk for Announcement Service
START
Dial the announcement service code Station “A” dials the announcement service code.
Check the contents of the 
announcementStation “A” is connected to the announcement trunk and 
hears the announcement.
Dial the announcement service code Station “B” dials the announcement service code.
Check the contents of the 
announcementStation “B” is...

NDA-24234 CHAPTER 5
Page 339
Revision 3.0
INSTALLATION TEST PROCEDURE
NAP-200-039
Sheet 1/1
Connection Test-Paging Trunk for Paging 
Access Service
START
Dial the paging access code Station “A”/ATTCON dials the paging access code and hears
CRBT (Continuous Ringback Tone).
In about 1 second, CRBT stops.
Speaker Paging Check whether speaker paging is possible after CRBT has 
stopped.
Release Station “A” goes on-hook or the ATTCON depresses the 
CANCEL key.
END
LCA
ATTCON
PGT
AMP SP 

CHAPTER 5 NDA-24234
Pag e 34 0
Revision 3.0
INSTALLATION TEST PROCEDURE
Paging Transfer Service can be selected according to System Data (SYS1, INDEX 73).
1. Non-Delay System
2. Delay and Non-Delay System
3. Paging Transfer Supervision
NAP-200-040
Sheet 1/2
Connection Test-Paging Trunk for Paging 
Transfer Service
START
Call the Paging Trunk Stations “A” and “B” are engaged in a station to station 
connection.
Station “A” makes a Switch Hook Flash (SHF) and hears 
SPDT. Station “B” is held on the line....