Home > NEC > Communications System > NEC Neax 2400 Imx Fusion Network System Manual

NEC Neax 2400 Imx Fusion Network System Manual

    Download as PDF Print this page Share this page

    Have a look at the manual NEC Neax 2400 Imx Fusion Network System Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1168 NEC manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							CHAPTER 7 ND-70185 (E)
    Page 166
    Revision 3.0
    TROUBLESHOOTING
    23-U FCH Status Information
    9.5 FLTINF = 1FH Spanning Tree Generation Start
    This message is displayed when Spanning Tree Generation starts.
    Figure 7-22   23-U FCCH Status Notification - Spanning Tree Generation
    9.6 FLTINF = 85H Checksum Verification Failure
    This message is displayed when Checksum verification has resulted in failure between the PBX and the firm-
    ware.
    Figure 7-23   23-U FCCH Status Notification - Checksum Verification Failure
    1. xx 0x  1F xx  00 00   00 00          2.  00 00   00 00   00 00   00 00.........
    MG
    UG
    FCH Mounting Location
    FCH CKT No.TRC
    RS
    00
    MG: Module Group 
    U: Unit (0-3)
    G: Group (0-23)TRC: Trace Confirmation Bit
    (0/1 = Status Notification / Primitive Trace)
    RS: Receive / Send Primitive Trace (not effective)
    FCH CKT No. = Circuit No. of FCH
    
     1FFLTINF: 1FH = Spanning Tree Generation Start
    Spanning Tree Generation Start:  00H = Normal
    b7 b0b7 b0b7 b0b7 b0
    Spanning Tree Generation  Start
    1. xx 0x  85 xx  xx 00   00 00          2.  00 00   00 00   00 00   00 00.........
    MG
    UG
    FCH CKT No.TRC
    RS
    FCH Mounting Location
    00
    MG: Module Group 
    U: Unit (0-3)
    G: Group (0-23)TRC: Trace Confirmation Bit
    (0/1 = Status Notification / Primitive Trace)
    RS: Receive / Send Primitive Trace (not effective)
    FCH CKT No. = Circuit No. of FCH
    
     85FLTINF: 85 H =  Checksum Verification Failure 
    Checksum of PBX 
    b7 b0b7 b0b7 b0b7 b0b7 b0
    Checksum Verification Failure
    Checksum of Firmware 
    						
    							ND-70185 (E) CHAPTER 7
    Page 167
    Revision 3.0
    TROUBLESHOOTING
    23-W FCH Alternate Routing Start Notification
    10. 23-W FCH Alternate Routing Start Notification
    This message is displayed when the indicated FCH card of self-Node becomes inoperative. This message is also
    displayed when the card is placed in make busy status by MNT 3 switch operation. In addition, when the FCH
    of the adjacent node becomes inoperative, this message is displayed.
    Figure 7-24   23-W FCCH Alternate Routing Start Notification
    11. 23-X FCH Alternate Routing End Notification
    This message is displayed when an inoperative FCH card of self-Node resumes its operation. Therefore, when
    the card is placed in make idle status by MNT 3 switch operation, this message is also displayed.
    Figure 7-25   23-X FCCH Alternate Routing End Notification
    1. xx0x  0000 0000 0000    2. 0000 0000 0000 0000      3. 0000 .........
    MG
    U
    G
    FCH Mounting Location
    FCH Mounting Location
    MG: Module Group 
    U: Unit (0-3)
    G: Group (00-23)
    FCH CKT No.
    Circuit Number of FCH (0 - 7)
    b0 b7b0 b7
    1. xx0x  0000 0000 0000    2. 0000 0000 0000 0000      3. 0000 .........
    MG
    U
    G
    FCH Mounting Location
    FCH Mounting Location
    MG: Module Group 
    U: Unit (0-3)
    G: Group (00-23)
    FCH CKT No.
    Circuit Number of FCH (0 - 7)
    b0 b7b0 b7 
    						
    							CHAPTER 7 ND-70185 (E)
    Page 168
    Revision 3.0
    This page is for your notes. 
    						
    							ND-70185 (E) CHAPTER 8
    Page 169
    Revision 3.0
    CHAPTER 8 EX- FCCS
    1. General
    This feature provides the following functions (they are activated when connecting multiple Fusion networks) or
    a NEAX2000 IVS
    2 system to a Fusion Network using the Enhanced CCIS feature. The network connected by
    EX-FCCS function is referred as EX-FCCS Network in this manual. The network connected via Enhanced CCIS
    function is referred to as Enhanced CCIS network in the manual.
    1. Number PortabilitySee Section 3.1 “Number Portability”.
    The Telephone Number data in a Fusion Network can be moved to another different Fusion Network by a
    simple command operation from the sole Centralized-MAT in multiple Fusion Networks connected
    through EX-FCCS link or Enhanced CCIS link. See “Centralized Maintenance (Centralized-MAT for EX-
    FCCS)” for explanation of the Centralized-MAT. 
    2. Centralized Maintenance (Centralized-MAT for EX-FCCS) 
    See Section 3.2 “Centralized-MAT for EX-FCCS”
    All nodes (NEAX2400 IMX system) in the multiple Fusion Networks and NEAX2000 IVS
    2 systems con-
    nected through Enhanced CCIS link can be maintained from one MAT. The MAT used for Centralized
    Maintenance is called as “Centralized-MAT for EX-FCCS”.
    3. Inter-network service equivalent to CCIS features
    For details of CCIS features activated through EX-FCCS networks and Enhanced CCIS networks, see 3.3
    “CCIS Features Activated with EX-FCCS”.
    For the basic operation or the data programming for NEAX2000 IVS
    2, see other manuals specified the
    NEAX2000 IVS2 system. 
    						
    							CHAPTER 8 ND-70185 (E)
    Page 170
    Revision 3.0
    EX- FCCS
    EX-FCCS Network Configuration
    2. EX-FCCS Network Configuration
    2.1 Network Configuration
    The summary of network configuration classified into two types are shown in Ta b l e  8 - 1. See Table 8-1 in
    conjunction with Figure 8-1 for easy understanding of network configuration. The following items and sec-
    tions explain more details.
    Note:[Hardware Configuration] 
    For IMX to IMX connection type, both FCH and CCH cards are available.
    Fo r  I V S
    2 to IMX connection type, FCH card is not available. Use CCH card.
    *PA-SC18 (CCH) card is not available for the EX-FCCS network establishment.
    There are two connection types. 
    (1) NEAX2000 IVS
    2 to NEAX2400 IMX connection (Enhanced CCIS) 
    (2) NEAX2400 IMX to NEAX2400 IMX connection (EX-FCCS)
    Figure 8-1   Network Connection Type Table 8-1 EX-FCCS Network Type Classification
    × : Available
    TYPECONNECTION 
    TYPEA MAXIMUM 
    NUMBER OF 
    TELEPHONE NUM-
    BERSERVICE CENTRALIZED FUNCTION
    IMX to 
    IMXIVS2 to 
    IMXIMX to 
    IMXIVS2 to 
    IMXMAINTE-
    NANCEBILLING MCI
    1FCCSEnhanced
    CCIS120,000FCCS 
    serviceCCIS 
    service
    ×××
    2EX-
    FCCSEnhanced
    CCIS120,000CCIS 
    serviceCCIS 
    service×××
    (1) NEAX2000 IVS2 to 
    NEAX2400 IMX
    Legend
    : EX-FCCS : FCCS
    FCCS NETWORK 1
    IVS2
    (2) NEAX2400 IMX to 
    NEAX2400 IMX
    FCCS NETWORK 2
     IMX
    IMXIMX
    : Enhanced CCIS
    IVS2
    IMX
    IMXIMX 
    						
    							ND-70185 (E) CHAPTER 8
    Page 171
    Revision 3.0
    EX- FCCS
    EX-FCCS Network Configuration
    2.2 Conditions for Network Establishment (NEAX2000 IVS
    2 to NEAX2400 IMX Connection) 
    Conditions for connecting the NEAX2000 IVS2 to NEAX2400 IMX are described below.
    1. All IVS
    2 systems must be directly connected to an IMX. See Figure 8-2.
    Figure 8-2   NEAX2000 IVS2 to NEAX2400 IMX Connection
    2. The number of logical routes available (899) in the FCCS network is reduced by one for every route
    provide in the NEAX2000 IVS2 when connected via Enhanced CCIS. 
    Note:The above is a condition of data assignment in the NEAX2400 IMX system. The NEAX2000 IVS2 system
    accommodates up to 255 nodes (including NEAX2400 IMX and NEAX2000 IVS2 systems). The number of
    point codes assignable in the NEAX2000 IVS2 system is a maximum of 255, including Enhanced CCIS net-
    works.
    3. When directly connecting a NEAX2000 IVS
    2 to a NEAX2400 IMX, one signal channel may support
    multiple voice routes. However, when the Enhanced CCIS function is provided with EVENT BASED-
    CCIS, a signal route must be provided per voice route.
     
    NEAX2000 IVS2 (B) cannot be added to NEAX2000 IVS2
    NEAX2400 IMX.
    Enhanced CCIS
    IMXIVS
    2 (A)
    IVS2 (B)
      (A) which is already connected with 
    UNAVAILABLE   
    						
    							CHAPTER 8 ND-70185 (E)
    Page 172
    Revision 3.0
    EX- FCCS
    EX-FCCS Network Configuration
    2.3 Conditions for Network Establishment (NEAX2400 IMX to NEAX2400 IMX Connection) 
    Conditions for establishing a FCCS network (NEAX2400 IMX to NEAX2400 IMX) are shown below. 
    1. Each Fusion Network can accommodate a maximum of 253 network IDs.
    2. Each Fusion Network can accommodate a maximum of 899 logical routes.
    3. The NCN and NDM exist individually in each Fusion Network.
    Figure 8-3   NEAX2400 IMX to NEAX2400 IMX Connection
    Network configuration of the NEAX2400IMX to NEAX2400IMX connection is as follows.
    FPC1
    (NCN)FPC2
    FPC4 FPC3FPC1
    (NCN)FPC2
    FPC3 FPC4
    Fusion Network (B)
    In this Fusion Network,
    NDM (a) is used.
    In this Fusion Network,
    NDM (b) is used.
    FPC1
    (NCN)FPC2
    FPC4 FPC3
    LGRT3
    LGRT3 LGRT4
    In this Fusion Network,
    NDM (c) is used.
    : EX-FCCS
    : Fusion Group (FUG) : FCCS
    Fusion Network (A)
    Fusion Network (C)
    LGRT1, 2
    LGRT899
    LGRT1, 2
    LGRT200
    LGRT100
    LGRT899
    Network configuration of the NEAX2400 IMX to NEAX2400 IMX connection is as follows. 
    						
    							ND-70185 (E) CHAPTER 8
    Page 173
    Revision 3.0
    EX- FCCS
    EX-FCCS Network Configuration
    2.4 Fusion Network Group (FUG)
    [Fusion Network Group (FUG)]
    When connecting multiple Fusion networks using EX-FCCS, a Fusion Network group number is required
    to distinguish different Fusion Network groups. A Fusion Network Group is called as “Fusion Group
    (FUG)”. A maximum of 4 FUGs can be connected via EX-FCCS.
    [Center Fusion Group (Center FUG)]
    Identify the Center Fusion Group (Center FUG) from the FUGs in the EX-FCCS network. This is the sole
    node allowed  to assign or delete Telephone Numbers within the self FUG and the other FUG. 
    1. An EX-FCCS network may consist of FUGs (connected via EX-FCCS) and NEAX2000 IVS
    2 sys-
    tems (connected via Enhanced CCIS). All FUGs must be connected to the Center FUG within a range
    of 1 or 2 EX-FCCs links or 1 or 2 Enhanced CCIS links from the Center FUG. In order for an end-to-
    end connection to be established, no more than 4 EX-FCCS or Enhanced CCIS links may be used. See
    Figure 8-4. 
    Figure 8-4   Allowable SPAN from the Center FUG
    An exam ple of EX-FCCS Network configuration is shown in this figure. In this exam ple, FUG2 is the 
    Center FUG .
    LEGEND
    : EX-FCCS : Fusion G roup (FUG) : F C C S
    FUG2
    IV S2
    FUG3
    FUG1
    FUG4
    Center FUG
    IV S2
    IV S2
    IV S2IV S2
    IV S2
    : Enhanced CCIS 
    						
    							CHAPTER 8 ND-70185 (E)
    Page 174
    Revision 3.0
    EX- FCCS
    EX-FCCS Network Configuration
    2.5 Interactions
    1. Conditions for PS Service
    Roaming and Hand-over feature cannot be activated between FUG-FUG in an EX-FCCS network and
    FUG-IVS
    2 in an Enhanced CCIS network. To execute roaming service, connect other Q.931a/IS-
    11572 lines.
    2. Conditions for OAI/ACD Service
    The OAI/ACD service in EX-FCCS Network is executed on the same condition in CCIS Network. 
    						
    							ND-70185 (E) CHAPTER 8
    Page 175
    Revision 3.0
    EX- FCCS
    EX-FCCS Features
    3. EX-FCCS Features
    3.1 Number Portability
    [Operating Procedure] 
    1. Log in to the NCN of the Center FUG from the Centralized-MAT for EX-FCCS.
    2. Assign the Telephone Number data using AELGN command. The new data is automatically copied to
    the NDM in the self-FUG and the other FUG in an EX-FCCS network. AELGN command is also
    used to delete or change Telephone Number data in addition to assignment.
    Note 1:AELGN command is used to operate Number Portability for Telephone Numbers used in NEAX2400 IMX
    systems. For the NEAX2000 IVS2 system, several commands are required for assignment. For details, see
    related NEAX2000 IVS2 manuals.
    Note 2:When logging in to the node other than the NCN of the Center FUG (LN in Center FUG or LN/NCN in
    other FUGs), only reading out the AELGN command data is available. 
    Note 3:If the center FUG group is not “0” and FUG no.“0” is assigned to another group, AELGN command data
    assignment is available for the node to be logged in only.
    [Service Conditions]
    1. A closed numbering network is recommended for numbering plan of the EX-FCCS network.
    2. Only Telephone Number (max. 8 digits) is allowed for the extension number used in an EX-FCCS
    network. 
    						
    All NEC manuals Comments (0)

    Related Manuals for NEC Neax 2400 Imx Fusion Network System Manual