NEC Neax 2400 Imx Fusion Network System Manual

CHAPTER 5 ND-70185 (E)
Page 86
Revision 3.0
DATA PROGRAMMING
Assignment of FCH Related Data
STEP 4: ACAN
Assign the Fusion Connection Index Code (FCIC) and the LENs on an adjacent FPC basis. Figure 5-
34 shows a sample data sheet for Node A.
Note:It is not necessary to assign the same number as trunk and FCIC. However, FCIC numbers between adja-
cent nodes must be identical.
Figure 5-34   ACAN Sample Data Sheet
The ACAN command display should look similar to the following:
Figure 5-35   ACAN Command...

ND-70185 (E) CHAPTER 5
Page 87
Revision 3.0
DATA PROGRAMMING
Assignment of FCH Related Data
7.1 Assignment of Access Code for Tandem Connection via FCCS - ACIS
For Release 3 or later software, tandem connection via FCCS - ACIS link can be established. Using LDM,
appropriate routing data for each node can be assigned as shown in the following example.
Note:When the related data is assigned to DM, outgoing connection is available only for external routes in self
node (i.e. FCCS - ACIS link cannot be...

CHAPTER 5 ND-70185 (E)
Page 88
Revision 3.0
DATA PROGRAMMING
Assignment of FCH Related Data
STEP 1: ANPDN/ANPDL  Note
Assign the first digit of the OGC access code. When the access code is common to all nodes, use the
ANPDN command. When the access code is assigned for each node, use the ANPDL command.
1st DC=9 CI=N (Normal) NND=1
1st DC=9 CI=H (Hooking) NND=1
STEP 2: ASPAN/ASPAL  
Note
Assign the OGC access code. When the access code is common to all nodes, use the ASPAN com-
mand. When the access code...

ND-70185 (E) CHAPTER 5
Page 89
Revision 3.0
DATA PROGRAMMING
Assignment of FCH Related Data
7.1.2 OGCA
A procedure for assigning OGCA access code is explained using the following example.
Figure 5-37   Example of OGCA
STEP 1: ANPDN/ANPDL  Note
Assign the first digit of the OGCA access code. When the access code is common to all nodes, use
the ANPDN command. When the access code is assigned for each node, use the ANPDL command.
1st DC=9 CI=N (Normal) NND=1
1st DC=9 CI=H (Hooking) NND=1
STEP 2: ASPAN/ASPAL...

CHAPTER 5 ND-70185 (E)
Page 90
Revision 3.0
DATA PROGRAMMING
Assignment of FCH Related Data
STEP 3: ANNDL/AMND
Assign the necessary number of digits using the ANNDL or the AMND command depending on the
route data.
 When the ARTD command OSGS is 2 (Second Dial Tone), use the ANNDL (Necessary Digits
Data) command.
RT=100 OG NND=12
RT=200 OG NND=12
 When the ARTD command OSGS is 4/6/7 (Sender Immediate Start/Sender Delay Dial Start/
Sender Wink Start), use the AMND command.
DC=9 MND=12
STEP 4: ARSCN...

ND-70185 (E) CHAPTER 5
Page 91
Revision 3.0
DATA PROGRAMMING
Assignment of FCH Related Data
STEP 1: ANPDN/ANPDL  Note
Assign the first digit of the LCR/LCRS access code. When the access code is common to all nodes,
use the ANPDN command. When the access code is assigned for each node, use the ANPDL com-
mand.
TN=1 1st DC=8 CI=N (Normal) NND=1
TN=1 1st DC=8 CI=H (Hooking) NND=1
STEP 2: ASPAN/ASPAL   
Note
Assign the LCR/LCRS access code for a dummy route number. When the access code is common to
all...

CHAPTER 5 ND-70185 (E)
Page 92
Revision 3.0
DATA PROGRAMMING
Assignment of FCH Related Data
STEP 5: ARTD/ARTDN
Using ARTD, assign the following CDN data for the dummy route number.  Note 1
CDN 6 (TCL)=1 or 4 (depending on requirement) 
CDN 7 (L/T)=1
CDN 13 (AC)=1
The other CDNs may be left default (data 0) for the dummy route.
STEP 6: AFRSL/AFRSN  Note 2
Using AFRSL, assign the Number Pattern Code (NPC) and the Outgoing Route Selection Pattern
Number (OPR) for the dummy route number.
LGRT=Dummy route...

ND-70185 (E) CHAPTER 5
Page 93
Revision 3.0
DATA PROGRAMMING
Assignment of FCH Related Data
7.2 Data Assignment for 52M-SDH Interface
This section explains the Fusion Connection with 52M-SDH interface, which is available for Release 4 or
later software.
The figures below explain the connection pattern.
F u s i o n
Node-A
Optical Fiber Cable
Optical Fiber Cable
For Dual Configuration Connection Link (Data Link)
Connection Trunk (Speech Path)
Internal LAN
FCH
S
D
T
B
Node-B
Internal LAN
S
D
T
BFCH+...

CHAPTER 5 ND-70185 (E)
Page 94
Revision 3.0
DATA PROGRAMMING
Assignment of FCH Related Data
Specifications for the SDH data setting are described below.
1. When FCCS and CCIS links are used together in the network, the different route number must be assigned
to each Connection Trunk (B-ch), Connection Link (D-ch), Speech Line for CCIS and Signal Line for
CCIS.
2. System data (SYS1, INDEX 531) must be assigned prior to the trunk data assignment for the SDT.
3. When the SDT card is used to replace with the...

ND-70185 (E) CHAPTER 5
Page 95
Revision 3.0
DATA PROGRAMMING
Assignment of FCH Related Data
 Connection Link (for Data)
C_RT: 11
TCL=4 LSG=13
STEP 3: ACTK
Assign the Connection Trunk data for B-ch and D-ch.
Example:(When using 512kbps (8ch) TS as Connection link)
 Connection trunk (B-ch)
C_RT: 10 TK: 1-664 CLENS: LEN for the SDT
 Connection Link (D-ch)
C_RT: 11 TK: 1-8 CLENS: LEN for the FCH
C_RT: 11 TK: 9-16 CLENS: LEN for the SDT
Note:Set the switch on the FCH card depending on the transmission...