NEC Neax 2400 Imx Fusion Network System Manual

CHAPTER 5 ND-70185 (E)
Page 66
Revision 3.0
DATA PROGRAMMING
Assignment of Logical RT in Network DM (NDM)
4. Assignment of Logical RT in Network DM (NDM)
4.1 ALRTN/ARTKN
This command is used to assign Logical Route Numbers to all external trunks used on a Fusion network.
Assign unique Telephone Numbers to the whole route for external trunks on the network  (including COT,
DAT, Dummy Route, etc.) using this command. The data can be set at the NCN only and should be set for
every external route in every...

ND-70185 (E) CHAPTER 5
Page 67
Revision 3.0
DATA PROGRAMMING
Assignment of Numbering Data for Telephone Numbers
The ALRTN command display should look similar to the following:
Figure 5-12   ALRTN Command Display
5. Assignment of Numbering Data for Telephone Numbers
STEP 1: ANPDN
Make a Telephone Numbering plan on the network. The explanation is given here on the assumption
that the network adopts the numbering plan shown below. Therefore, make modifications to the data
assignment explained here when you...

CHAPTER 5 ND-70185 (E)
Page 68
Revision 3.0
DATA PROGRAMMING
Assignment of Numbering Data for Telephone Numbers
STEP 2: ANPDN
Assign Pre-translation Data for the Telephone Numbers planned in Step 1 using the ANPDN com-
mand at NCN. In Figure 5-14, the data setting should be as follows:
Figure 5-14   ANPDN Sample Data Sheet
The ANPDN command display should look similar to the following:
Figure 5-15   ANPDN Command Display
Note:
Perform the Numbering Plan data setting by using ANPD command in the same way...

ND-70185 (E) CHAPTER 5
Page 69
Revision 3.0
DATA PROGRAMMING
Assignment of Numbering Data for Telephone Numbers
STEP 3: ASPAN
Assign special access code data for the Telephone Numbers using the ASPAN command.
SRV=TELN is the data for Telephone Numbers.
Figure 5-16   ASPAN Sample Data Sheet
Figure 5-17   ASPAN Command Display
Note:
The Numbering Plan data for the LDM and/or NDM cannot use separate Tenant Numbers (TN). Therefore,
be sure to assign the following data on the ASYDL command.
 ASYDL command,...

CHAPTER 5 ND-70185 (E)
Page 70
Revision 3.0
DATA PROGRAMMING
Assignment of Telephone Numbers
6. Assignment of Telephone Numbers
This section explains how to program Telephone Numbers. To program Telephone Numbers, use ALGSN com-
mand. Telephone Number can be assigned to a station  using the LENs or the Physical Station Number depend-
ing on programming.
Note:The Fusion Link must be operational before programming telephone numbers in the Fusion Network.
COMMAND: ALGSN/ATSTN
Assign Telephone Numbers to...

ND-70185 (E) CHAPTER 5
Page 71
Revision 3.0
DATA PROGRAMMING
Assignment of Telephone Numbers
Figure 5-19   ALGSN Command Display (example)
UGN
TELN
WRT?
ALGSN (Assignment of Telephone Station Data In Network)
11
Y
FPC
141000 TYPE
LENS
000100
Physical LENS Telephone Number

For Help, press F1

NUM
UGN
TELN
WRT?
ALGSN (Assignment of Telephone Station Data In Network)
21
Y
FPC
1TN
1 41000 TYPE
STN
2000
Physical Station Number Telephone Number

For Help, press F1

NUM 

CHAPTER 5 ND-70185 (E)
Page 72
Revision 3.0
DATA PROGRAMMING
Assignment of Telephone Numbers
6.1 Assignment of Connection Route/Trunk Data
STEP 1: ACRD
Using the ACRD command, assign the connection route data of Fusion link. The data must be assigned for both
B-channel and D-channel. Assign appropriate data referring to the Table 5-1.
Figure 5-20   B-ch and D-ch
The ACRD command should look similar to the following.
Figure 5-21   ACRD Command Display (example)
NECNEAX 2400 IMS
Fusion Network
D ch
D ch B...

ND-70185 (E) CHAPTER 5
Page 73
Revision 3.0
DATA PROGRAMMING
Assignment of Telephone Numbers
Table 5-1 Route Class Data Assignment
CDN Node A Node B
Description type B-channel D-channel B-channel D-channel
RT C_RT: 10 C_RT: 11 C_RT: 12 C_RT: 13
1TF3333Trunk Kind 3: Bothway (fixed)
2TCL4444Trunk Class: 4 (fixed)
3RLP2222Release Method : Assign 2-First Party 
Release.
4SMDR0000Assign 0.
5 LSG 12 13 12 13 B-ch: 12, D-ch: 13
6PAD
7 TRKS 0 (1) 0 0 (1) 0 0: FIFO (1: LIFO)
8TC/EC
9FINT0000Fusion Interface Kind:...

CHAPTER 5 ND-70185 (E)
Page 74
Revision 3.0
DATA PROGRAMMING
Assignment of Telephone Numbers
CDN 1: Trunk Kind
0-2: -
3: Bothway Trunk
CDN 2: TCL (Trunk Class)
0-3: -
4: Fusion Trunk
5-31: -
CDN 3: RLP (Release Pattern)
0: Calling Party Release
1: -
2: First Party Release
3: -
CDN 4: SMDR (SMDR for station-to-station call)
Assign 0.
CDN 5: LSG (Line Signal)
12: B channel for No.7 CCIS/ISDN
13: D channel for No.7 CCIS/ISDN
CDN 6: PAD   
Note
0: Depending Key Setting of Circuit Card
1: Send 8 dB, Receive 0...

ND-70185 (E) CHAPTER 5
Page 75
Revision 3.0
DATA PROGRAMMING
Assignment of Telephone Numbers
CDN 10: FPEG (Fusion Trunk Peg Count)
Assign 0.
CDN 11: TC (Timer Class)
0: -
1: 1 sec
2: 2 sec
3: 8 sec
4: 20 sec
5-7: -
CDN 12: MTC (Miscellaneous Timer Counter)
CDN 13: STSEQ (Status Enquiry)
0: -
1: cancel
CDN 14: FGH (Fusion Gateway Handler)
Assign 0.
CDN 15: MMN (Kind of Multiple Equipment)
0: TDM
1: MM-Node
2-3: -
CDN 16: Fusion Link
0: via DTI
1: via  ISW
2: Fusion over IP (Router)
3-15: Not used
CDN 17:...