NEC Neax 2400 Imx Fusion Network System Manual

CHAPTER 5 ND-70185 (E)
Page 76
Revision 3.0
DATA PROGRAMMING
Assignment of Telephone Numbers
STEP 2: ACTK
Assign the connection trunk data of both B-channel and D-channel using the ACTK command. As-
sign the Connection Equipment Number (C_LENS) referring to Figure 5-22 through Figure 5-25.
The ACTK command display should look similar to the following.
Figure 5-22   ACTK Command Display (example)
The mounting location of the FCH, DTI cards can be classified into the following two types.
Regular Density...

ND-70185 (E) CHAPTER 5
Page 77
Revision 3.0
DATA PROGRAMMING
Assignment of Telephone Numbers
Table 5-2 Data Programming Sheet for Regular Density Slot
C_RT
(1-1023)C_TK(1-4095)C_LENS
Time Slot Allocation
MG U G LV
10 (B-ch)1
000010
2000011
3000012
4000013
5000014
6000015
7000016
8000017
9000020
10000021
11000022
12000023
13000024
14000025
15000026
16000027
17000030
18000031
19000032
20000033
21000034
22000035
23000036
11 (D-ch)1000037
2000270
0405
01
2703
00
02Dch (TK1)
Bch (TK23)
Bch (TK1)
Dch (TK2) Bch...

CHAPTER 5 ND-70185 (E)
Page 78
Revision 3.0
DATA PROGRAMMING
Assignment of Telephone Numbers
6.1.2 When FCH is Mounted in a High Density Slot
If the FCH is to be mounted in the High Density Slot, the connection trunk data should be assigned as
shown in the figures below. Figure 5-24 shows an example where these cards are mounted in Slots 11
and 12.
Figure 5-24   Mounting FCH and DTI Cards in High-Density Slots
00 02 04 05 06 07 08 09 10 13 14 15 16 17 18 19 20 21 22 23
12 13 1415
0001
02 0001
02 0404...

ND-70185 (E) CHAPTER 5
Page 79
Revision 3.0
DATA PROGRAMMING
Assignment of Telephone Numbers
When the DTI cards is mounted in a double density slot, the C_LEN data for the FCH and DTI cards
are as follows.
Figure 5-25   How to Assign C_LEN Data (Type 2)
0002 04 05 06
0708 09
1011 12
1314 1516
1718
1920
2122
23
04 02  00 06 1005 07 11
12 131415
161718
0001
02 04 06 08 10 03 05 07 09 11
1213 14 15
1617 18 19
20 21 22 23
08 09
PIM
Universal SlotsUniversal Slots
PWR DPWR TSW/MUX TSW/MUX03 01
FCH
DTI 
DTI...

CHAPTER 5 ND-70185 (E)
Page 80
Revision 3.0
DATA PROGRAMMING
Assignment of Telephone Numbers
Table 5-3 Data Programming Sheet for High Density Slot
C_RT
(1-1023)C_TK
(1-4095)C_LENS
Time Slot Allocation
MG U G LV
10 (B-ch)1 000210
2 000211
3 000212
4 000213
5 000214
6 000215
7 000216
8 000217
9 000220
10 000221
11 000222
12 000223
13 000224
14 000225
15 000226
16 000227
17 000230
18 000231
19 000232
20 000233
21 000234
22 000235
23 000236
11 (D-ch)1 000237
2 000190
1112
19 23
22
21Dch (TK1)
Bch (TK23)
Bch...

ND-70185 (E) CHAPTER 5
Page 81
Revision 3.0
DATA PROGRAMMING
Assignment of FCH Related Data
STEP 4: MBCT
Unbusy the connection trunk data assigned in the previous step using MBCT (Make Busy of Connec-
tion Trunk) command. This step is required for both B-channel and D-channel trunk. The MBCT
command should look similar to the following.
Figure 5-26   MBCT Command Display
7. Assignment of FCH Related Data
STEP 1: For Fusion with FCH only:
 Assign FCH Number on an FCH (PA-FCHA) circuit card basis. 
 The...

CHAPTER 5 ND-70185 (E)
Page 82
Revision 3.0
DATA PROGRAMMING
Assignment of FCH Related Data
Figure 5-29 shows a sample data assignment when FCH cards are located in the PIM 0 slot 4 and PIM 2 slot 11.
Figure 5-27   Assignment of FCH Number
The AFCH command display should look similar to the following:
Figure 5-28   AFCH Command Display (example)
NECNEAX 2400 IMS
FCHN=2
LENS: 000270FCHN=1
As an example, data assignment when FCH cards are accommodated in the following slots is shown here.
PIM 0, slot 4 and...

ND-70185 (E) CHAPTER 5
Page 83
Revision 3.0
DATA PROGRAMMING
Assignment of FCH Related Data
STEP 2: AFRT (Fusion with FCH only)
Assign connection route numbers as shown below using the AFRT command.
Figure 5-29   AFRT Sample Data Sheet
The AFRT command display should look similar to Figure 5-30.
Figure 5-30   AFRT Command Display
FCHN = 1

CNT = 1     C_RT : 10


LN
LN
LN LN
LN LN
NCN1
2
C_RT=10
Node A
Node BFCIC=1
FCHN=1
FCIC=1FCIC=2
FCIC=n
FCIC=2
FCIC=n
TRK 1
TRK 10TRK 3TRK 31
TRK 32
TRK 40 :
::...

CHAPTER 5 ND-70185 (E) 
Page 84
Revision 3.0
DATA PROGRAMMING 
Assignment of FCH Related Data
STEP 3: AFPCAssign FCH routing data using the AFPC command. A maximum of 8 connection routes and FCHN/ 
FPCN can be assigned on a node basis. FCHN is used for Fusion System with FCH. FPCN is used
for Fusion System without FCH. The list box labeled FCH on the AFPC command determines the 
system type. Assign “0” for Fusion System without FCH and “1” for Fusion System with FCH. In 
this step, the explanation is...

ND-70185 (E) CHAPTER 5
Page 85
Revision 3.0
DATA PROGRAMMING
Assignment of FCH Related Data
The table in Figure 5-33 shows a sample data sheet for Node A on a Fusion network with FCH. Assign the data
for all nodes including the nodes which are not directly connected on the network. For example, in this figure
Node C and Node D are not directly connected to the network.
Figure 5-33   AFPC Sample Data Sheet
FPC 2(to Node B) FCCH 1(with FCH)

CNT    C_RT    FCHN
1         10          1

FPC 21(to Node...